similar to: htb.init question

What is the maximum value for "prio"? It seems that for htb its maximum is 7. Is that right? R. -- ___________________________________________________________________ It''s so simple to be wise. Just think of something stupid to say and say the opposite. +------------------------------------------------------------------+ | Richard Lucassen, Utrecht

Hello list, I have these sorts of filters, putting traffic into the appropiate classid (1:15 is the default class): ${TC} filter add dev ${DEV_IFB} parent 1:0 prio 1 protocol ip u32 \ match ip protocol 0x6 0xff \ match ip sport 22 0xffff \ classid 1:11 # ssh ${TC} filter add dev ${DEV_IFB} parent 1:0 prio 1 protocol ip u32 \ match ip protocol 0x6 0xff \ match ip dport 22

Is it possible to create 1 filter rule using fw selectors AND u32 selectors? Richard. -- ___________________________________________________________________ Recursion: see recursion +------------------------------------------------------------------+ | Richard Lucassen, Utrecht | | Public key and email address: | |

Is it possible to negate the "match" to the ip? I want to match all traffic to dport 80 NOT going to dst 1.2.3.4: $TC filter add dev ${DEV_IFB} parent 1:0 prio 2 protocol ip u32 \ match ip protocol 0x6 0xff \ match ip dport 80 0xffff \ match ip dst 1.2.3.4/32 \ classid 1:14 I can''t find it in the docs. I tried "!" "\!" and "not" in several

Packets going to a 2.6 kernel IPSEC tunnel do not seem to pass the POSTROUTING chain. Is that correct? R. -- ___________________________________________________________________ It''s so simple to be wise. Just think of something stupid to say and say the opposite. +------------------------------------------------------------------+ | Richard Lucassen, Utrecht

I have 1 100MB NIC with two 2MB-subnets trough a router behind it. I''d like to create multiple default classes: 1: + |\_ 1:10 default, ceiling 100000kbit, rate 96000kbit | |\_ 1:11 ceiling 2048kbit, rate 2048kbit | | | |\_1:110 ceiling 2048kbit, rate 1536kbit | \_1:111 ceiling 2048kbit, rate 512kbit (default subnet1) | \_ 1:12 ceiling 2048kbit, rate

Hello list, Please don''t shoot me. I know I''m doing something with bonding that bonding wasn''t made for. I just want to give it a try. I want a simple mechanism to have a failover on a 24Mbit line to a 2Mbit line in case the 24Mbit line goes down. Between A and B there are two lines: a 24Mbit and a 2Mbit. I use two OpenVPN tunnels with tap devices: +-- tap0 (A)---

I''m a newbie to tc and after some experimenting I have the following problem: # tc qdisc show qdisc sfq 8006: dev ipsec0 quantum 1514b perturb 15sec I can''t get rid of this entry. Is there a way to clear all entries? I tried all sorts of "tc qdisc del xxx" but nothing seems to work. It says: RTNETLINK answers: No such file or directory What syntax do I need to

Is it possible (one way or another) to guarantee or to limit bandwidth of 1 session? E.g.: RDP: 750kbit rate, 1Mbit ceil default: 250kbit rate, 1Mbit ceil max bw per RDP connection: 100kbit guaranteed bw per RDP session: 20kbit R. -- ___________________________________________________________________ It''s so simple to be wise. Just think of something stupid to say and say the

Is there a qdisc that allows a per connection maximization? E.g.: bandwidth 1Mb, four sessions RDP and a per session limit of 250kb R. -- ___________________________________________________________________ It is better to remain silent and be thought a fool, than to speak aloud and remove all doubt. +------------------------------------------------------------------+ | Richard Lucassen,

Hello list, I''d like to use teql with tap devices (two OpenVPN tunnels). This works, but the doc /usr/src/linux-<version>/net/sched/sch_teql.c says: "1. Slave devices MUST be active devices, i.e., they must raise the tbusy signal and generate EOI events. If you want to equalize virtual devices like tunnels, use a normal eql device." I can''t find if tap devices

I set up this config: +------+ -+ ISP1 +--+ +------+ | +-------+ +--+ linux | +------+ | +-------+ -+ ISP2 +--+ +------+ No problem. Standard setup with two ISP''s. Both routed subnets. Default gateway is ISP1. No magic here. Now I put a server behind the Linux box. I want the server to be reachable on an /extra/ IP in the routed subnet of ISP2. +------+ -+ ISP1

Hi, I am trying to setup a shaper for my linux box and I am experiencing some problems. What I am trying to do is priorizing packets on the egress link, therefore I have setup some prio classes etc. The priorizing seem to work but the problem is that the ceil parameter doesnt seem to work on non leafs. This is what stats show: > class htb 1:1 root rate 3000bit ceil 3000bit burst 1602b/8 mpu

Hi, I am trying to do some simple ingress limiting based on fwmark. I know the ability and sense to do INGRESS limiting is ehm... limited ;-) but still I want to try it. I tried several things. === 1 === tcq ingress handle ffff: tcf parent ffff: protocol ip prio 1 handle 1 fw police rate 12mbit burst 10k drop tcf parent ffff: protocol ip prio 1 handle 2 fw police rate 10mbit burst 10k drop

This is one of my test classes: class htb 1:10 parent 1:1 prio 0 quantum 2048 rate 160Kbit ceil 400Kbit burst 1803b/8 mpu 0b cburst 2111b/8 mpu 0b level 0 Q1: where does "level 0" stand for? Q2: where does this b/8 stand for? Q3: this is on a i386 platform, so timer resolution should be 10mS. According to the doc the minimal burst should be 10mS*160Kbit=1600. Why is it 1803? Q4: I

Second test after big upgrade.. -- http://www.PowerDNS.com Open source, database driven DNS Software http://netherlabs.nl Open and Closed source services

Hello, I''am successful using a linux (2.4.20) bridge and the cbq.init_v0.7 script for traffic shaping. But I can only use the queuing discipline tbf (LEAF=tbf). If I try use queuing discipline sfq or none then tc applies the rules but no shaping occurs. Is this problem a normal behavior when using bridging ? I tried to use htb.init (using patched tc binary). It accepts the rules but

Hi to all, i''m using htb.init for configuring my shaper. Now i want to know if it possible to show how htb.init make and use TC, anyone has tried it? Many thanks. -- Stefano Mainardi Presidente Associazione ILDN - Italian Linux Distro Network Mobile: 349/3917212 Skype: mainardistefano IM (ICQ): 250-292-408 Blog: http://www.mainardistefano.org

why the exemple in the htb.init of the BURST e CBURST comes with values if the dafault is computed? Is it better to put these values manualy? How can I calculate the values?

Hi to all, i''m using htb.init for configuring my shaper. Now i want to know if it possible to show how htb.init make and use TC, anyone has tried it? Many thanks. -- Stefano Mainardi Presidente Associazione ILDN - Italian Linux Distro Network Mobile: 349/3917212 Skype: mainardistefano IM (ICQ): 250-292-408 Blog: http://www.mainardistefano.org