similar to: Routing by interface as opposed to ip address?

Hi Couple months ago I started to have a strange problem with HTB. My setup is Fedora Core 2 + Pentium 2 233 + 128 MB of ram and its serving as a router. For some time since going to kernel 2.6 my HTB QoS Stalls for couple seconds, every couple minutes. If the connection load is bigger the stalling is more frequent and takes longer. I isolated the problem to be with HTB (CBQ works fine). The

Hi, How can I set equal bandwidth of 512kbit downlink and 256kbit uplink for every single IP address of 254 IP addresses I have in my LAN? Regards, ro0ot

Is any way to detect changed MAC adresses? Someone taught change MACs peoples in my network and I have problems. E.g. Two computers working on one MAC, and one IP (static ARP and DHCP). WinXP is screaming some message... that two computers or more have the same IP. How can I find out who''s changed MAC?

Hi, I am trying to control bandwidths of the connections by using TC with HTB. But I want to implement Leaky Bucket on this structure so as to have a straight flow. Due to being new in this area, could anyone help me how I could do this? Does TC support leaky bucket? Best regards, Fatih Duzova

Hi all, i need advice how can i limit ip_conntrack per IP. clients of network that i support often uses torrent , DC++ , eMule clients and i have lost packages because they open too many ports. i have traffic control limits but this obviously isn''t enough Any advance how to prevent server from this kind problems will be welcome. Best regards Emil

I am looking for a simple way to guarantee to each flow going through my traffic control point 1/numflows of bandwidth. I thought using SFQ would do this effectively but it appears to be quite unfair: a very high speed download that fills the pipe easily starves smaller flows to the point where it becomes unusable (especially if they are at all interactive) Because numflows is dynamic,

Folks, I''m so surprised what happened to my box just in the few weeks lately. Here is my setup: INTERNET <----------> [eth0] SHAPER-BOX [eth1] <----------> USER-FARM both eth0 & eth1 got public ips (202.x.x.x) Why traffic monitored at eth0 is bigger than eth1 ? eth1 shaped just exactly the same as rate i defined in HTB. I just have 1024Kbps from my ISP and i defined the

Hi Is there a program which allow me to see how "my" traffic goes through my iptables rules? Which accept it, which deny? Right now my router has a little bit of traffic and its hard to see only mine traffic. -- Miłego Dnia Krystian Antoni _______________________________________________ LARTC mailing list LARTC@mailman.ds9a.nl http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc

Hi, I am writing this email in sincere hope that somebody experienced similar/same problem and found solution to it. The classical bridge setup could be achieved using brctl tool, which could be found at: http://home.regit.org/br2684.html I have an ADSL CO line card Linux based [2.4.24 kernel] with 8 nas interfaces and eth0. Rather than having bridge, the decision was to have a router, which

Hello Everybody, I have configured a Linux box that does traffic shaping. Its working wonderfully fine, just as expected...Now i want to measure the bandwidth consumed by each of my hosts....But I dont want SNMP to run on all the hosts[as required by MRTG] I used iptraf on my linux box, but it only measures the bandwidth on interface basis only.... I tried installing traffic-vis, its not working

I have compiled chan_oh323 and when starting * I get the following. [chan_oh323.so]Aug 15 12:40:00 WARNING[1076245120]: loader.c:242 ast_load_resource: /usr/lib/asterisk/modules/chan_oh323.so: undefined symbol: __use_ast_pthread_create_instead__ Aug 15 12:40:00 WARNING[1076245120]: loader.c:423 load_modules: Loading module chan_oh323.so failed! Can anyone tell me how to fix this, or what

Hi All. I'm using RedHat 9 I configured the chan_h323 and asterisk from CVS. This is the scenario SJ_lab_phone(sip) ---------------> Asterisk -------------> H323 GK --------------> PSTN I have tried all codec's and always the same result, the called phone will ring without dropping for how ever I allow it to but as soon as it is answered it immediately gets disconnected.

Hi All I'm trying with no luck to connected the Quintum D series Gateway with the new SIP release to asterisk. Have anyone done this? If yes then how should I configure the sip.conf to accept the registration? maybe a sample config? Thanks /Krystian

Colleagues- I am working on the design of a fairly large samba deployment, and I am looking for feedback on some of my design ideas. I have 10 buildings spread out in and around a city, all interconnected via 1.5Mb leased lines. There are samba servers in each building. I have some users that move from building to building. We are using primarily windows 98 desktops, with a few 2K and XPP

Hi all I have asked this question before but have not got any helping input. I'm really new to this and need some explanation about ASTCC. So here is the question again. In the ASTCC web admin there are Trunks, Routes, IAXFriends, SIPFriends, Brands, Cards. As I understand Brands is not used, Cards just makes the cards. Routed in the dialplan and pricelist, Trunks is for ASTCC to

https://bugzilla.samba.org/show_bug.cgi?id=6573 Summary: Documentation Error: Section with exact title doesn't exist Product: rsync Version: 3.0.6 Platform: Other URL: http://samba.anu.edu.au/ftp/rsync/rsyncd.conf.html OS/Version: All Status: NEW Severity: normal Priority: P3

Hello everybody, I have a Linux router with an ethernet adapter and a ADSL device. My router has a GRE tunnel connected to a remote IP address. Using "tc" I have configured 3 different classes: 1. 290kbit rate (used for Voip Services) 2. 180kbit rate (used for GRE tunnel) 3. 80kbit rate (for generic data traffic) For each class, using "iperf", I send some data from a PC

I get an echo when going from a SIP phone to a PRI trunk. I hear the echo on the SIP phone. From reading some other post I think that I need to tell me phone company to turn on echo canceling. If the echo was on the other end than it would be my problem? Is this right? What exactly should I say to my phone company so they know exactly what I'm talking about? -- Michael Sampson

Guys, What was the rationale behind moving to the swiss army-ish method of render(:X), as opposed to the various render_X methods that existed before? I find it easier to keep the render_X style in my brain, rather than trying to remember what the valid parameters to render() are. It''s also more code completion friendly. Just curious. Thanks, John -- Posted via

Just wondering. http://www.vorbis.com/ Regards...martin -- Maslow's Maxim: If the only tool you have is a hammer, you treat everything like a nail.