similar to: imq + htb

i''m trying to limit upload and download but something is wrong(it is about NAT) i will post here my "script" maybe someone could tell me what is wrong my kernel(2.6.9) is patch with imq(linuximq.net) and my iptables(1.2.11) also #flush tc qdisc del dev eth0 root tc qdisc del dev eth1 root tc qdisc del dev imq0 root tc qdisc del dev imq1 root ifconfig imq0 down

Hello, I''m trying to get my shaper to work, but have only a partial success. Can someone help me with that. My setup unfortunately is not so trivial, but I think some people could have similar one... 1. There is a router connected to the internet line via interface eth0 2. There are users connected to the router via two interfaces : eth1 and wlan0 3. All users are assigned private IP

Hi. The configuration script is at the bottom. My configuration looks similar to this: imq0 | 1:1 (12mbit) | 1:2 (10mbit) | 3:0 | 3:1 (256kbit) / \ 3:2 3:3 icmp (rest) both 3:2 and 3:3 have rate 1kbit ceil 256kbit Icmp bucklet have priority 1 (better), "rest" bucklet have prio 2 (worse) I tested the script with heavy download

Hi I have tested with FC3 but iam not able get any good results on that. in the list some one recomend me that > 3.17 HTB should work I saw latest FC4 test2 has the HTB 3.17 with iptables 1.3.0 i have install in my P4 box, and trying to test when iam uploading its working perfect, but when iam downloading its going to default class can some one experinced the same problem below is the my

Thanks for quick reply Andreas! > Every class is allowed to use bandwidth as long as it does not have to > borrow (the specified rate is guaranteed). Prio in HTB only affects > borrowing bandwidth from other classes... In the example below, the class > 1:5 should be allowed to borrow bandwidth before 1:14 does. Thats exactly what I want from HTB to do..to prio the borrowed bandwidth.

Hello, I wrote a simple traffic shaping script (below) that should have allowed me to shape my internet traffic a bit (ppp0 - adsl 128kbit/64kbit; local interface eth0). The script works only partially - the speed is being limited but too much. Without running this script my download rate is about 10kBytes (with second computer also downloading at about 6kBytes). After running it my download speed

I have: tc qdisc add dev imq0 root handle 1: htb default 30 tc class add dev imq0 parent 1: classid 1:1 htb rate 512kbit ceil 512kbit tc class add dev imq0 parent 1:1 classid 1:30 htb rate 64kbit ceil 512kbit then: iptables -t mangle -A PREROUTING -i ppp0 -s 192.168.2.2 -j IMQ --todev 0 tc class add dev imq0 parent 1:1 classid 1:22 htb rate 64kbit ceil 128kbit tc filter add dev imq0 protocol

Hello to all people there . Can i guarantee ICMP respond time no metter how loaded is internet line . i have typical NATed enviroiment like External IP |linux router| LAN - 192.168.0.0/24 i have example setup with IMQ but is it possible to be done also if i attache htb to eth0 and eth1 for example . if i start shaper ping i better that without shaper but it''s not guarantted i mean

first: my ISP mark MAN traffic with TOS 15 and i want tu can to filter this kind of traffic with iptables second: i use imq patch for kernel 2.6.9 and htb for some traffic management third: i want to redirect the traffic marked with TOS 15 imq1 or imq0 and then to came with some htb rules. just this ... how must to modified to can to do some thins ? ... #iptables -t mangle -A PREROUTING -m

Hi ! I want to share my bandwidth between 10 computers. I want to redirect computer A(192.168.1.4) to htb class 1:2 and the others to htb class 1:3. But the last tc filter doesn''t work : Error message : "Unknown filter "flowid", hence option "1:3" is unparsable. " I know the option "default" for htb but I don''t want to use it for some

On my debian woody (kernel 2.4.31) the tcpdump doesn''t work with imq0 devices. If I try to tcpdump imq devices there is no packet seen: [...] rt1:~# tcpdump -n -i imq0 Warning: arptype 65535 not supported by libpcap - falling back to cooked socket tcpdump: WARNING: imq0: no IPv4 address assigned tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on

Hi All, I''m trying to create a contended section of bandwidth using IMQ. I have the imq0 device up and running, with traffic passing through it. Firstly, I need to throttle the entire device imq0 to 2mbit/s. I would then like to add throttle rules for individual IP addresses, allowing them to pass up to 512kbit/s each, as long as imq0 has not reached its 2mbit/s. The configuration

Folks, I''m so surprised what happened to my box just in the few weeks lately. Here is my setup: INTERNET <----------> [eth0] SHAPER-BOX [eth1] <----------> USER-FARM both eth0 & eth1 got public ips (202.x.x.x) Why traffic monitored at eth0 is bigger than eth1 ? eth1 shaped just exactly the same as rate i defined in HTB. I just have 1024Kbps from my ISP and i defined the

Hello I have a server with a dsl connection on eth1 and local interface eth0. Because of the NAT i cannot direct traffic to IMQ device in PREROUTING chain but have to use INPUT and FORWARD. So i use rules. iptables -t mangle -A INPUT -i eth1 -j IMQ --todev 0 iptables -t mangle -A FORWARD -i eth1 -j IMQ --todev 0 And now the strange thing: FORWARD traffic gets directed nicely to the IMQ, but

Hello... Im trying to setup HTB to allow me to shape traffic from two upstreams that meets on single lan0 interface. I prefer to use HTB qdisc within HTB root qdisc for cleaner rules design. Seems that it doesnt work at all. tc -s class show doesnt show any traffic on other classes attached to HTB qdisc. Linux 2.6.20.7 iproute-2.6.20-070313 Weird thing is that tc -s class show that 1: and 2:

Hi all ! I''m building a network appliance whose goals are to enhance Voip quality on 512/128k DSL links. But, i have a voice quality problem, and i think i''m doing something wrong, but i can''t find what. Please excuse my terrible english, i''m french. >From what i''ve read, tc is the tool i need. I read the documentations, readmes and lartc.org

Hi folks, I have three network cards on my Slackware box and eth0 and eth1 are for two Internet connections. They have imq0 and imq1. All traffic shaping works fine. Internal eth2 does no traffic shaping. But recently I have put two OpenVPN tunnels (tun devices) and both work via eth0. So my question is - how to shape the traffic on these tun0 and tun1 devices? Thanks Remus

Hello everyone... I have a little trouble and need some help :P How can I check on which interface the packet is going (eth0, eth1; I have two ISP and on eth3 little LAN), using to check it TC and IMQ? (HTB script) I tried to mark packets, but on chain POSTROUTING this does not work... Maybe because packets fall on IMQ before signing. I tried marking it on FORWARD but packets also

Hello, I have HTB on IMQ device. My rate does not work as I configured. I configured 1920kbit/s and I can download only about 290kbit/s (while it should be the whole bandwidth). My script: /sbin/modprobe imq numdevs=1 /usr/local/sbin/tc qdisc del dev imq0 root 2> /dev/null > /dev/null /usr/local/sbin/tc qdisc del dev imq0 ingress 2> /dev/null > /dev/null /sbin/ifconfig imq0 down