similar to: Is this possible?

Hi, I am trying to setup a shaper for my linux box and I am experiencing some problems. What I am trying to do is priorizing packets on the egress link, therefore I have setup some prio classes etc. The priorizing seem to work but the problem is that the ceil parameter doesnt seem to work on non leafs. This is what stats show: > class htb 1:1 root rate 3000bit ceil 3000bit burst 1602b/8 mpu

Andreas, Since I understand your ASCII art and comments, I would very much appreciate it if you would draw what you see and criticize the following. Hopefully I''ll better understand after that! TIA, gypsy tc qdisc add dev imq0 root handle 1: htb default 20 tc class add dev imq0 parent 1: classid 1:2 htb rate 4522kbit ceil \ 4760kbit burst 16k cburst 16k quantum 1500 tc class add

Hi, I''m trying to setup QoS in my TSL box. Following to mailing list reccomendations I changed PSCHED_CPU but can''t get accurate shaping with HTB. I have disabled HYSTERESIS also (by setting it to 0). I have Intel Celeron 1.8Mhz (TSC supported I think). ******** My script ****** tc qdisc add dev eth0 root handle 1: htb default 22 r2q 10 # Class corresponding interface

Dear All! I reach the point that I must ask you what I have to do. I am beginner at traffic shaping and I''m very confused with it. :) Here''s my script that doesn''t do what I want to do with it: tc qdisc del dev eth1 root tc qdisc add dev eth1 root handle 1 htb default 2 r2q 10 tc class add dev eth1 parent 1: classid 1:1 htb rate 300kbit tc class add dev eth1 parent 1:

Hi! I recently changed my qdisc from CBQ and PRIO to only HTB, and I can''t really seem to get the rates to work as I want them to. I have eight classes, which I set up as follows: tc qdisc add dev eth1 root handle 1: htb default 122 tc class add dev eth1 parent 1: classid 1:1 htb rate 1000kbit ceil 1000kbit cburst 1500 burst 50kb tc class add dev eth1 parent 1:1 classid 1:11 htb prio 0

Hello, First of all, I already contacted Martin Devera, the developer of HTB, and he told me to search for help on this mailinglist, thus I am describing my problems here now... I am kind of seriously annoyed by QoS as I have been trying for over 3 years to get it working properly - first I did not understand how it works, then it seemed not to work, then it was working perfectly for half a

Hello all, I am trying to make a filter into my QoS rules and I founded that when I try to use filters u32 and with fwmark they do not work together. This is the filter I use, just and example, for u32: $TC filter add dev $DL parent 1:0 protocol ip prio 1 u32 match ip sport 22 0xffff flowid 1:10 This is working fine. Now if I try to mark a package that I want it to go to the same

Hi all, I''ve not been able to find an explanation of the relationship between prio and rate as they apply to the HTB technique. Hopefully someone on here will be able to help me. As I understand things, when prio values are assigned to an HTB setup, classes with a given prio value will only be serviced when there are no packets waiting in classes with a lower prio value. Now, does

Hi all, I''m experimenting with HTB and the prio parameter and it does not give me results I expect. I''ve created 4 HTB classes: 1:10 TCP ACKs (prio 0) 1:20 TCP traffic on dst port 10001 (prio 1) 1:30 TCP traffic on dst port 10000 (prio 2) 1:40 Default (prio 3) ceil and rate parameters are the same for all 4 classes (rate is

Hi! I have just started with traffic shaping, and after hours of reading websites, man pages asf. I am still stumped at one problem I have. The interface eth0 is attached to the outside world, and I have an openvpn tunnel to another part of the organization using eth0 and port 5001. The idea was that all traffic going through the tunnel would have top priority and the rest share

Hi, this is my Linux Box ---------------------------- LAN 1 -----|--eth1 <---br1--->eth0.1 | | \ | | eth0--|----- 802.1q tagged 1 Mbps link | / | LAN 2 -----|--eth2 <---br2--->eth0.2 | ---------------------------- I have to bridge the 2 lans

With the below script, whenever I ping 10.0.16.10 (which matches the only filter I have), traffic still get''s sent to the default 1:2 class instead of 1:1 and I don''t know why... Any hints? (kernel 2.6.12, iproute2-2.6.15) tc qdisc del dev eth0 root > /dev/null 2>&1 tc qdisc add dev eth0 handle 1: root htb default 2 tc class add dev eth0 classid 1:1 parent 1: htb rate

Hi, I have some interesting problem with htb , I set up root class and sub-classess: $TC qdisc add dev eth0 root handle 1: htb $TC class add dev eth0 parent 1: classid 1:1 htb rate 1990kbit ceil 2000kbit $TC class add dev eth0 parent 1:1 classid 1:10 htb rate 190kbit ceil 200kbit $TC class add dev eth0 parent 1:1 classid 1:11 htb rate 1400kbit ceil 1600kbit $TC class add dev eth0 parent 1:1

Hello to everybody, We want integrate in a router/firewall (Debian Based, 2.6 Kernel), an HTB shaper. The goal is to divide the traffic for classes of workstations, at example in three classes, let say A, B and C. Example: A 70 Mb/s B 20 Mb/s C 10 Mb/s If B don''t make traffic, 7/8 of 20Mb/s must be assigned to A and all the rest at B We have used CBQ and HTB, with poor succes. Anybody

Hi all, my IMQ device works OK (thanks to Andy Furniss), but now I''ve problems to attach the traffic in the qdisc''s. This is my conf: ----------------------------------------------------------------------- INET | |eth0 300Kbps ROUTER (NAT) |eth1 | LAN ----------------------------------------------------------------------- MAX=300 tc qdisc add dev imq0 root handle 1: htb

Hello, I have begun to use the tc scripts since 2 weeks ago, so I am beginner. I am trying to divide my bandwidth in 4 independent ones. Each of these sub-bandwidths is assigned to 4 different groups of ip. Bandwidth sharing is allowed. I put a Linux with two Ethernet card between the router and the LAN. Eth1 is the card connected to the router and eth0 is the one connected to the LAN. My ISP

I''m trying to shape each machine on an interface to 256k each, but I''m getting stuck and only able to shape an entire interface to 256k. What should I be doing differently here? tc qdisc del dev eth0 root tc qdisc add dev eth0 root handle 1: htb default 10 tc class add dev eth0 parent 1: classid 1:1 htb rate 100MBit ceil 100MBit tc qdisc add dev eth0 parent 1:10 handle 110:

Hi all I''m new in this list and i hope to lear and to help if possible. But firt i need help :-( I have this messege in my syslog when my classes and qdiscs goes down. Can any one know what does it mean? Thnx in advance. Yannick Arrimadas Bot Oct 14 16:09:27 pototogorri kernel: HTB init, kernel part version 3.17 Oct 14 16:09:27 pototogorri kernel: Unable to handle kernel paging

Hello everyone, First of all, sorry for my poor english. I''ve been working with this for a few weeks and I''m getting sick... I''m trying to control the bandwith in my network using the following script. The machine where the script is running makes NAT, eth0 is connected to the router and eth1 is connected to the Lan. When I run the script it doesn''t appear any

Hi Stef, Sorry to write to you directly but my list membership is not working, I receive the archive but cant send to the list, cant delete myself because I don''t exist and can''t rejoin as they say I do exist, anyway hope you don''t mind Can you tell me what the difference between these two scripts is please. What I want to achieve is a high speed channel 1000kbit from