similar to: Guarantee ICMP respond time ?

i''m trying to limit upload and download but something is wrong(it is about NAT) i will post here my "script" maybe someone could tell me what is wrong my kernel(2.6.9) is patch with imq(linuximq.net) and my iptables(1.2.11) also #flush tc qdisc del dev eth0 root tc qdisc del dev eth1 root tc qdisc del dev imq0 root tc qdisc del dev imq1 root ifconfig imq0 down

Hello, I''m trying to get my shaper to work, but have only a partial success. Can someone help me with that. My setup unfortunately is not so trivial, but I think some people could have similar one... 1. There is a router connected to the internet line via interface eth0 2. There are users connected to the router via two interfaces : eth1 and wlan0 3. All users are assigned private IP

Hello, I wrote a simple traffic shaping script (below) that should have allowed me to shape my internet traffic a bit (ppp0 - adsl 128kbit/64kbit; local interface eth0). The script works only partially - the speed is being limited but too much. Without running this script my download rate is about 10kBytes (with second computer also downloading at about 6kBytes). After running it my download speed

Hi, i am running imq + htb on my router , the situation is like this eth0 = uplink to my provider eth1 = 1st customer eth2 = 2nd customer eth3 = 3th customer eth0 has limit 512 and i want to share this between eth1 eth2 and eth3 , but not working , this is the script i used, \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ #!/bin/sh

Hi All, I''m trying to create a contended section of bandwidth using IMQ. I have the imq0 device up and running, with traffic passing through it. Firstly, I need to throttle the entire device imq0 to 2mbit/s. I would then like to add throttle rules for individual IP addresses, allowing them to pass up to 512kbit/s each, as long as imq0 has not reached its 2mbit/s. The configuration

Folks, I''m so surprised what happened to my box just in the few weeks lately. Here is my setup: INTERNET <----------> [eth0] SHAPER-BOX [eth1] <----------> USER-FARM both eth0 & eth1 got public ips (202.x.x.x) Why traffic monitored at eth0 is bigger than eth1 ? eth1 shaped just exactly the same as rate i defined in HTB. I just have 1024Kbps from my ISP and i defined the

On 2/19/07, Salatiel Filho <salatiel.filho@gmail.com> wrote: > Well , thanks to imq all my client machines are now shaped and > everything is great ... > But now i have a doubt , is there a way to shape the traffic that goes > to the route [doing a wget from the router for example ]? > > > I have a PREROUTING IMQ0 and a POSTROUTING IMQ1 , everything is > working like

Hi. The configuration script is at the bottom. My configuration looks similar to this: imq0 | 1:1 (12mbit) | 1:2 (10mbit) | 3:0 | 3:1 (256kbit) / \ 3:2 3:3 icmp (rest) both 3:2 and 3:3 have rate 1kbit ceil 256kbit Icmp bucklet have priority 1 (better), "rest" bucklet have prio 2 (worse) I tested the script with heavy download

Hello, I''ve just recently started to use IMQ and I got puzzled after seeing the imq usage example on the linuximq.net site: It was something like this: tc qdisc add dev imq0 handle 1: root htb default 1 tc class add dev imq0 parent 1: classid 1:1 htb rate 1mbit tc qdisc add dev imq0 parent 1:1 handle 10: htb default 5 tc class add dev imq0 parent 10: classid 10:1 htb rate 256kbit

Hi, I can''t get traffic shaping working. This is my situation: -------- ------ Net1 ----- |router| -------------------- | TC | ----------- Net2 -------- leased line ------ eth1 eth0 We use the leased line for normal traffic but also for synchronisation between 2 servers. The leased line is 2mbit. The synchronisation

I''m using HFSC to limit bandwidth for our wireless customers. However, I''d also like the bandwidth prioritized based on packet type. This is what I''m trying right now, and I''d just like some input from anyone out there knowledgeable in this on whether it does what I want it to do: Eth1 -> HFSC ........|-> HFSC (User1) (Min 512 Kb, Max 1024 Kb, Burst 1536

Hi ! I have a single host which is connected via an 512kbit ADSL link to the n= et. I quite often use some realaudio application that uses some bandwidth = and I want to avoid other traffic to scale that bandwidth down. So I used = some classes (with htb) on imq0 device and applied some filters and it see= ms to work in most cases. However, there are some sites with which downloa= d is

Hi all, my IMQ device works OK (thanks to Andy Furniss), but now I''ve problems to attach the traffic in the qdisc''s. This is my conf: ----------------------------------------------------------------------- INET | |eth0 300Kbps ROUTER (NAT) |eth1 | LAN ----------------------------------------------------------------------- MAX=300 tc qdisc add dev imq0 root handle 1: htb

Hi folks, I`ve a problem to use HTB and SFQ. The first script, below, to show a simple configuration, does work fine...!!! But, in the second example, does not work, becouse i put more code to clasify the traffic by protocol, http and ftp in this case. Somebody can tell me the errors? Thx, in advance.- NOTICE: IMQ device is to asociate with ETH1 my external iface. SCRIPT que funciona:

Hi, I wanted to implement some QOS on my Linux Box with HTB, but after some time spend on the configuration and tests, I still don''t manage to have some correct results. Here are the details : -ROOT 2000 kbits -HIGHPRIO SUBCLASS 50 kbits prio 0 -SUBCLASS1 750 kbits prio 1 -SERVICE1 250 kbits prio 1

I''m trying to shape traffic on a Devil-Linux box. This note was originally sent to their maillist, because the LARTC list appears to have been down for the past few days. My mailbox was just flooded with a half dozen or so confirmation requests in response to my repeated attempts to subscribe to this list. ---------- Forwarded message ---------- From: drew einhorn

hi stef oone more pb while shaping incoming traffic with imq .this one tc qdisc add dev imq0 root handle 1: htb default 20 tc class add dev imq0 parent 1: classid 1:1 htb rate 2mbit burst 15k tc class add dev imq0 parent 1:1 classid 1:10 htb rate 1mbit tc class add dev imq0 parent 1:1 classid 1:20 htb rate 1mbit tc qdisc add dev imq0 parent 1:10 handle 10: pfifo tc qdisc add dev imq0 parent

Hi all and tc Gururs i have patched the IMQ and htb to kernel, but when i do egress filtering, iam not able to see any traffic and excusted the following the commands modprobe imq numdevs=1 tc qdisc add dev imq0 handle 1: root htb default 1 tc class add dev imq0 parent 1: classid 1:1 htb rate 100kbit tc qdisc add dev imq0 parent 1:1 handle 10: htb default 1 tc class add dev imq0 parent

Hi All I am fighting this for 3 days and could not find any reason it is not working the way I want to (or I the way think it should). Internet output interface = eth2 (htb qdisc) Internet input interface = imq0 (eth2 attached - htb qdisc) main class = imq0 1:1 sub1 = 1:ffff (default) sub2 = 1:10 (src ports 1433/tcp or 1434/tcp or 81/tcp or 82/tcp) sub3 = 1:11 (src and dst port 25/tcp )

Andreas, Since I understand your ASCII art and comments, I would very much appreciate it if you would draw what you see and criticize the following. Hopefully I''ll better understand after that! TIA, gypsy tc qdisc add dev imq0 root handle 1: htb default 20 tc class add dev imq0 parent 1: classid 1:2 htb rate 4522kbit ceil \ 4760kbit burst 16k cburst 16k quantum 1500 tc class add