similar to: tunneled tc

I am attempting to setup an IPSec protected GRE tunnel with a Cisco router. I believe the IPSec association is up, however I cannot move traffic over the tunnel. It is not clear how to integrate the tunnel interface (gre1) with firewall-cmd; adding the interface to trusted does not appear to 'stick'. [root at aqueduct ~]# firewall-cmd --add-interface=gre1 --zone=trusted The interface

I am trying to setup GRE between two CentOS 4.5 boxes. I have tried several variations of what''s listed below, but none of them work. box1: modprobe ip_gre ip link set gre0 up ip tunnel add gretun mode gre local 66.1.1.161 remote 66.1.2.161 ttl 20 dev eth0 ip addr add dev gretun 10.253.253.1 peer 10.253.253.2/24 ip link set dev gretun up ip route add 10.2.0.0/16 via 10.253.253.2 box2:

Hi! I read http://mailman.ds9a.nl/pipermail/lartc/2002q4/006244.html and I did that. Can anyone tell me if there is something else to do for shapeing over tunnels to work? I noticed that gre interfaces don''t have a queue attached. I''m running linux-2.6.15 and iptables-1.3.4 with no patches. Thank you in advance, Sorin.

Hi Devik/Patrik, In setting up IMQ/HTB with a GRE Tunnel I''m constantly getting kernel errors: [root@linux /root]# dmesg ... ... ... NET: XXX messages suppressed. Dead loop on virtual device gre1, fix it urgently! ... ... ... This I get only if I''m going to start cross device b/w control. If I remove iptables rule iptables -t mangle -D POSTROUTING -j IMQ then no such warning

Hi! I want to add to my previous post that: my setup looks like this internet --> linux router with NAT and tc ==> gre tunnel ==> forwarding router --> LAN At my NATting router I can "see" the forwarded LAN (192.168.2.0/24). Now let''s say that there is a LAN workstation with the IP 192.168.2.18 and I filter the traffic with tc for it. If the fowarding router has

Hey all, Anybody been successful running DHCPD on a GRE tunnel? When I tell DHCPD to listen on cisco1 I see this in the log Jul 23 16:21:03 atlantis dhcpd: cisco1: unknown hardware address type 778 Here is the output of ifconfig cisco1 Link encap:UNSPEC HWaddr 8B-8E-28-32-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.199.0.2 P-t-P:10.199.0.2

I have a centos 4 i386 machine that works like a router (iptables filter, NAT) with two NIC''s. One NIC is connected to my ISP (100 Mbit FTTH), I get a DHCP assigned public IP that changes "sometimes". Most incoming ports are blocked by my ISP. In order to get a fixed IP and open ports, I have to set up a PPTP tunnel to the ISP. The default gw and the NAT''ing goes to

Hello, Here is my network: ------------------ ------------- ----------- Linux box ----------- GRE --------- Cisco ---------- ------------------ ------------- What I wan to accomplish. I want ripv2 to go across (both ways) through the GRE tunnel. No packets are being passed thought the GRE

Hello Lartc Mailing List: Been working on something the last week and a half and ALMOST have it working.., just need a few pointers from the wizards on this mailing list to nail it. Ok, my setup is a hub and spoke arrangement, hub is Cisco 2821 with IOS 12.4. Spokes are ruggencom RX1000 routers, Debian based with the following versions installed: rx1000test:~# uname -a Linux rx1000test

Hi everybody, I want to do the following setup : | | Tun1 - Link 1 | Tun1 | | Router A | teql | INTERNET Link - | | teql |router B | | Tun2 - Link 2 | Tun2 | | This should permit to agregate Link 1 and Link 2 (less the cost of the encapsulation). The two tunnels are GRE ip tunnel. It seems to work fine

Hello, I have a VM where I would like to setup a secondary interface which has an IP on a remote lan ideally with GRE. I have a simple GRE tunnel from dom0 to a cisco at the remote site, the tunnel works great I have routes in and I can ping between both sides dom0 and the remote router/lan. I had planned on just bridging the GRE interface with a new empty bridge then have the VM attach to that

Hello everybody, I have a Linux router with an ethernet adapter and a ADSL device. My router has a GRE tunnel connected to a remote IP address. Using "tc" I have configured 3 different classes: 1. 290kbit rate (used for Voip Services) 2. 180kbit rate (used for GRE tunnel) 3. 80kbit rate (for generic data traffic) For each class, using "iperf", I send some data from a PC

Hi Guys, Here is our patch to allow broadcast packets over a GRE tunnel. Hopefully it might be accepted into the source someday. You need to enabled bridging and GRE tunnels in your kernel. No other options are required. The gre patch determines what type of protocol type to put in the GRE header based on the whether the packet is forwarded from a bridge or not. To use the patch: # Create

I need to send multicast traffic through a GRE tunnel between two Linux routers. The tunnel works for normal IP packets, but I can''t see how to make it work for multicast. Here''s the setup: 10.10.10.0/24 LAN-B--------------RtrB-------------RtrC--------------LAN-C 192.168.2.0/24 192.168.1.0/24 RtrB interfaces: eth0

Hi All, As it is written in the "Linux 2.4 Advanced Routing HOWTO" GRE tunneling has some benefits compare to IP-in-IP, on of it benefits is the ability to transport multicast traffic through a GRE tunnel. I used the mrouted daemon and I know that the daemon supports tunneling but I don''t want to use its tunneling method. Assuming I have gre0 as my tunneling device I did the

Hi , I am trying to set up a GRE tunnel between two linux routers. The routers have a 400 MHz Processor. Linux .2 65.0.0.2 Linux LAN1 -------- Router -------- INTERNET ---- Router ---- LAN2 10.10.10.0 .1 208.1.0.1 (Simulated) .1 .1 192.168.2.0/24 /24 Scripts to Create the tunnel ip tunnel add tun0 mode gre remote 65.0.0.1 local

Hi All: I have a strange problem that was described in a previous mail but I have stripped the problem down to the following: I have a debian based router that I have setup IPSec with GRE over top. The tunnel addresses are 192.168.2.97 locally, the other side is 192.168.2.110. The tunnel is 192.168.2.96/28. The end points are locally 192.168.1.97(eth1) and 192.168.1.1 the other side''s

Hello, I''ve set up a GRE tunnel between two Linux boxes and it''s working well, with or without IPSEC (under GRE). The problem is that when I have no traffic for some minutes, side A cannot communicate to side B any more, unless side B tries to communidate to side A. The same thing happens in the other direction. For example, side A pings side B. No reply. Keep pinging. Side B

Hi, I have a problem with GRE tunneling. I read Advanced-Routing HOWTO about this and I did all as is written in this documentation. Even the same example is here which I need for my project. I want create (by means of GRE tunneling or IP in IP tunneling) virtual private network VPN - in first phase without IPsec in other phase with IPsec. I have two local networks distant apart with two routers.

Hi, Does anyone tried to get ipip or gre tunnel behind NAT environments. ? i''m trying to make both side tunneling with ipip or gre with private address just like belows.. A -------------------FIRWWAL -------------------INET ------------------- B PRIVATE PUBLIC PUBLIC (10.100.0.1) (211.xxx.xxx.xxx) (