similar to: FS: Cyclades PC300/TE2 Dual T1 Interface PCI Card For Linux PC!

I hope this isn''t too far off topic. I did a little bit of pricing homework a few months ago on new T1 cards. The idea was to build a Linux based router/firewall. After all, Ethernet NICs are easily available for less than $10 today. But all the T1 cards I found cost a fortune. And about a year ago, I learned the list price for a complete Adtran Netvanta 3200 router with T1 card is

I have a 5 year old machine that had a working cyclades8ys (8 port ISA rs232) card. I installed centos 4.1 on the box. I installed the kernel source and rebuilt the the kernel, did menuconfig and seelcted the cyclades module. Did the modprode cyclades and got some driver information echoed to the screen but it did not detect the card. Does udev have anything to do with this? Does any one have

Hello, I have been struggling with the configuration of this card on my box. I have a T1 line and I am trying to setup asterisk with it. I followed all the instructions and I still see a blinking red light on the card. I use fedora 12. If everything is fine should I see a green line when I plug in the T1 line ? I want to isolate the issue so I di not start asterisk. When I run asterisk I get

I have a server with an asterisk ss7 link connected to a Siemens working well for over a year. A few days ago I started having problems with signaling. I found the following logs in / var / log / messages Sep 12 11:49:25 call3 kernel: [1018427.030959] dahdi: Master changed to TE2/0/2 Sep 12 11:49:25 call3 kernel: [1018427.120740] dahdi: Master changed to TE2/0/1 Sep 12 11:49:26 call3 kernel:

# Span 1 span=1,1,0,esf,b8zs bchan=1-23 dchan=24 echocanceller=mg2,1-23 # Span 2 span=2,2,0,esf,b8zs bchan=25-47 dchan=48 echocanceller=mg2,25-47 # Span 3 span=3,3,0,esf,b8zs bchan=49-71 dchan=72 echocanceller=mg2,49-71 # Span 4 span=4,4,0,esf,b8zs bchan=73-95 dchan=96 echocanceller=mg2,73-95 # Global loadzone = us defaultzone = us Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1"

Hello. I have a TE212 configured in E1 mode. This is shown in a cat /proc/zaptel/2 and 3 (where the card is configured): cat /proc/zaptel/2 Span 2: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" HDB3/CCS/CRC4 RED NOTOPEN 25 TE2/0/1/1 Clear 26 TE2/0/1/2 Clear 27 TE2/0/1/3 Clear 28 TE2/0/1/4 Clear 29 TE2/0/1/5 Clear 30 TE2/0/1/6 Clear

hi after some testing with A@H, i've decided to install my asterisk server on a slackware (because it's my favourite distro and it is still suggested here http://www.voip-info.org/wiki-Asterisk+Linux+Slackware) , so, i've installed the last 10.2 release, and i've recompiled the 2.6.15.4 kernel. then i've downloaded asterisk1.2.4 and zaptel1.2.4 i load module zaptel and

Dear All; I am afraid from IRQ misses: 1 The ISDN E1 was working fine on the machine, the electrical disconnected and then the Red Allarm. I checked the dahdi and I found that I have to reinstall dahdi again and I did. But still not becoming UP. The output of the cat /proc/dahdi/1 is following (I am afraid from the IRQ misses: 1, so if it is a problem what is the solution)? [root at CC

I am having problem with T1 configuration. Following r the config.. Zaptel.conf # Autogenerated by /usr/local/sbin/genzaptelconf -- do not hand edit # Zaptel Configuration File # # This file is parsed by the Zaptel Configurator, ztcfg # # It must be in the module loading order span = 1,1,0,esf,b8zs # fxsks=1-24 bchan = 1-23 dchan = 24 # Span 1:

Hi, I've searched and searched on the possible problems. If anyone can help me that would be great. Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" (MASTER) B8ZS/ESF CRC4 error count: 4750 E-bit error count: 5023 Timing slips: 72 1 TE2/0/1/1 Clear (In use) (SWEC: MG2) 2 TE2/0/1/2 Clear (In use) (SWEC: MG2) 3 TE2/0/1/3 Clear (In

Hello, I'm running Asterisk@home 2.5 asterisk 1.2.4 zapatel 1.2.2 libpri 1.2.2 on a Dell Poweredge 2850 (1 CPU) with a TE210P I have 2 t1 circuits using NFAS with dchan on 24 and no backup dchan. I am able to receive inbound calls on all channels and can only make outbound calls on channels 25-48. Attempting to make an outbound call on channels 1-23 results in congestion.

Hi, On a Asterisk 1.8.12 system working OK for months (>100k calls proceed), users are complaining for bad audio. My setup is: PSTN <--E1/PRI ---> Asterisk <--- E1/PRI---> Siemens HiPath <---E1/PRI ---> PSTN asterisk -rx "dahdi show version" DAHDI Version: SVN-trunk-r10414 Echo Canceller: HWEC asterisk -rx "pri show version" libpri version: 1.4.12 A

I've done a decent size update of the OpenSSH portable from the upstream tree. There is an AES upgrade that needs to take place, but I need people to test and tell me what endedness changes need to be applied (if any). Attached is the patch. It is geared towards the latter snapshots..Unsure how it will patch (if at all) against 2.9pX series. Thanks. - Ben "This is dark day in

Hi, I am having problems with an Asterisk with a Digium TE205P card. The issue is that the Ring Back Tone is noisy. I am making modem's calls and this noise influences on the initial negotiation protocol, so modems have to recall. My configuration is: Asterisk version: Asterisk 1.4.21.2 Linux version: CentOS release 5.2 (Final) Card: Digium TE205P

Hi, I''m trying to configure QoS on my linux in the following manner: I have a main link with 64K, so I divided it in 3 classes of 18K, 14K and 9K with an excess (not used for classified traffic, just to be shared) of 23K. This excess should be distributed proportonally among the 3 classes, that is, the class that has more rate should borrow more bandwidth. What is happening is

Hello all. I have an NEC PBX connected via a TE210p E1 line to an asterisk 1.6 box. NEC -> E1 -> TE210P:1 -> * -> TE210P:2 -> E1 -> Telco Incomming calls from the telco to the asterisk box to the NEC work fine with indials and everything. Works sweet. Outbound from the NEC to the Asterisk box fail. Giving an long dial tone that then times out. Ie, pick up NEC handset, dial

Hi. My configuration is Elastix 1.5.2-2 (asterisk 1.4.24, libpri-1.4.3-5, dahdi-2.1.0.4-7 ) and OpenVox d210e connected to telco provider (Euro ISDN). Here is my /etc/dahdi/system.conf: # Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" (MASTER) HDB3/CCS ClockSource span=1,1,0,ccs,hdb3 # termtype: te bchan=1-15,17-31 dchan=16 echocanceller=oslec,1-15,17-31 # Span 2: TE2/0/2 "T2XXP

I've got an asterisk 1.4.24 box with dahdi complete 2.1.0.3+2.1.0.2 I've got a 2 port T2XXP card attached with on T1 currently plugged in. Inbound calls work fine, but outbound fail with the rather cryptic: [May 19 17:28:07] WARNING[11360]: app_dial.c:1237 dial_exec_full: Unable to create channel of type 'DAHDI' (cause 0 - Unknown) There are similar threads I've found on the

the Telco, I can make calls in. What I am trying to get though is how to pass through the DID range. The E1 that I am connecting to the Telco with, used to connect direct to the NEC system and already has hunt group calling enabled for all 30 channels. Also, I was given a 100 number indial range (from 00 -> 99). If the E1 is connected to the NEC directly, I can call 5555 7320 and the NEC

Hi All, I have a (legacy) Praxton PBX, it has a PRI T1 input card and 64 analog extensions through 4 amphenol connectors. We receive 12 voice channels (other 12 are idle) and have 100 DIDs. No caller ID thru PRI though. The Praxton box is amazing in terms of configuration and flexibility but has no VoIP support and the company went poof and it is no longer supported, nor spare parts are