similar to: Route by destination port?

snat not working my local ip is aaa.aaa.aaa.aaa asterisk sitting on the internet at ip bbb.bbb.bbb.bbb my firewall''s internal ip is 192.168.0.254 i did snat: iptables -t nat -A POSTROUTING -o ppp0 -j SNAT --to aaa.aaa.aaa iptables -t nat -L -v gives: Chain POSTROUTING (policy ACCEPT 23663 packets, 2182K bytes) pkts bytes target prot opt in out source destination 33056

Hi Here is a short description of my network: ppp0 (adsl) ppp1 (adsl) | | | | --------------------- | Router | | Firewall | | MASQUERAD | | DNAT | | | | eth0 | --------------------- | | | ---------------------- |

Hi, I have implemented QOS classifiers using TC with HTB. The classification is working. I would like to know whether there is some tool which will help me in monitoring the bandwidth share of the various classes. Thanks, Vinod C

i''ve read your http://lartc.org/howto/lartc.rpdb.multiple-links.html article as well as Advanced IP Routing (esp. chapter 10.4) and still unable to make this thing work. am i that helpless? :) is there anyone to guide me through the multiple ISP setup? into details. i got 2 dsl connections from different ISPs (A and B), both connections use PPPoE, both got assigned with dynamic IPs

Hello Shorewall list, I''m a happy Shorewall user since a few years now and everything works fine for me except one thing that I try to implement since a week, the multi-isp. I''ve downloaded the 2.4.0 Stable release yesterday and tried the RC2 since a week. My config is a Debian running a kernel 2.4.27 home made with the CONNMARK.diff patch applied I''m using 2 ISP,

Hi, I have established two connections to the same ISP. After that ip route list showed this: 195.14.247.94 dev ppp0 proto kernel scope link src 81.173.141.207 195.14.247.94 dev ppp1 proto kernel scope link src 81.173.237.84 192.168.0.0/24 dev eth0 proto kernel scope link src 192.168.0.1 default via 195.14.247.94 dev ppp0 I want 192.168.0.2 to connect to the internet by ppp1 and all

I need basic PPPoE startup help. adsl-start DID bring up my PPPoE link (ppp0) to my ISP over eth0 via the DSL modem/bridge. My IPv4 CIDR block is routing and Shorewall is doing the firewalling. But shorewall has to be started after ppp0 is up and working. For now this means running shorewall restart (or start?). Shorewall 4.2 will have a way to restart shorewall without recompiling, I

Hi. The task: 1. There 3 servers and a router with 2 PPPoE connections (let call them: ppp0, ppp1). 2. There are several groups of Inet-clients to be served (Servers, Clients and Club). 3. The task is: - to route Club through the ppp1; - to Servers and Clients through ppp0; (Next is reproduced from memory and may be slightly incorrect) router # netstat -nr Kernel IP routing table

I have two adsl lines on my linux firewall box and i want to do some load balance between them...i tried a lot of different things, but it isn´t working...Following the instructions of http://lartc.org/howto/lartc.rpdb.multiple-links.html i used the configuration above. using "iptraf" I can see some few packets using the ppp1 connection, but almost all the packets use ppp0 connection.

Hello all, Can anyone recommend a good book which thoroughly explains QoS from a Linux perspective? Something with TC examples & the like. I''ve looked at the following: http://www.amazon.com/gp/product/1580533418/qid=1148368189/sr=1-2/ref=sr_1_2/102-2819973-6353768?s=books&v=glance&n=283155 Engineering Internet QoS. Thanks.

Hi, I currently connect to my ISP via my adsl modem in bridge mode and PPPoE. I am due to put a second PPPoE ISP onto my firewall box which will give me ppp0 (general) and ppp1 (static leased line). The static leased line will run a number of services on its static IP and it is therefore imperative to make sure rules defined for the static line are assigned to the correct interface. I need this to

Hi, Thanks for the reply. Thats where the problem starts. If I set ppp0 as the default gw the internet doesnt work anymore. This is how im doing it... route del default route add default gw 217.32.81.74 dev ppp0 if I put it back to ppp1... route del default route add default gw 217.32.68.73 dev ppp1 It works fine again. Whats up with that? Cheers, Chris ----- Original Message

Hi, I''ve set up a Linux box with redhat on to act as an internet gateway and I''m running into a few problems. Its got two adsl modems connected to it, both connected to seperate 512kbs lines. Now I''ve followed the simple source routing in the advanced routing howto to the letter but it doesnt work. I''ve got it autoconnecting on startup and redhat puts ppp1

Hi all! I''ve got 2 (soon 3) internet connection. 1 - via ADSL, 2(and3) via ppp My network: http://desima.objectis.net/network-diag linux1: user1.user2 eth0=192.168.1.1 ppp0=192.168.5.2( gw 192.168.5.1) gw=192.168.1.2 ( thru ADSL) compA=192.168.1.6 compB=192.168.1.15 gw2=192.168.1.217 via ppp to different ISP All works for compA and CompB, user1 should use default gw(192.168.1.2)

My Internet gateway is using ADSL PPPoE connection with dynamic public IP assigned by ISP. My Internet gateway is Redhat AS3 U2, shorewall 2.0.9 As my ISP provided 4 simultaneous pppoe dailup connection for the same physical adsl line. My linux server can be configured for multiple pppoe connection i.e. ppp0, ppp1, ppp2, ppp3 Is it possible of shorewall to assigned say ppp0''s IP is

Hi ! Recently i switched my internet provider, to get more speed but another braindead setup regarding public ip addresses. I now have 4 PPTP Tunnel available, of which i''m using one as the gateway ip doing masquerading to other machines in my local lan, excluding three other machines, which i would like to use 1:1 nat to get them a direct access to one of the pptp tunnels. I was

Hi, can anyone help me with this problem i''ve got! I have a problem with routing on my Mandrake 7.2 Linux Box i was wondering if you could help me with. I live in Australia and as broadband access isn''t very available at the moment, i have 2 modems to dialup to my isp (dynamic ips assigned) to increase my bandwidth at an affordable level. What currently happens is i have a

Hi all .... I Have installed Bering LRP on Many sites and I am very pleased with the capabilites of shorewall. Howerver I came across a prob that I am unaware ot its solution. Using shorewall 2.0.2f Kernel 2.4.24 On one Site LRP box serves internet outgoing connections through ( static IP ) a DSL line AND an incoming dial-in PPP conection. My shorewall configuration Is based upon the fact

how to use iproute/iptables to balance by packet OUTBOUND traffic between 2 PPP (pptp cable modem and pppoe adsl modem) links to the same ISP . also by using the fact that the ISP dosen''t filter source IP address - meaning i can use either PPP''s link assigned IP address as the source IP in the ip header.., it works for both devices.., what i want to achive is : when uploading a

I had been using L7-Filter[1] successfully for edonkey/eMule traffic until recently. I upgraded to the latest release of mldonkey, 2.5.28a, which implements eMule compatibility, and with support for Kademlia[2] enabled, network latency increases greatly. [1] http://l7-filter.sourceforge.net/ [2] http://www.infoanarchy.org/wiki/wiki.pl?Kademlia Has anyone created a new pattern match for