similar to: Problem with routing for multiple uplinks/providers using iproute2

HI All , I am running a FC6 box with two internet links with load balance . Every thing is working fine expect the MSN connection that failed and reconnect every time and SSL connections . I would link to know if with the nona howto I could fix that . I have been tried with no success to redirect that connection only to one link but its look like do not work . Here my configuration :

Hi, this might be a dumb question, but I''m not finding much information online. I''m trying to setup a 2.6 linux box to run nat across multiple upstream links as a simple way to aggregate bandwidth. I found the instructions in lartc section 4.2 (http://lartc.org/howto/lartc.rpdb.multiple-links.html) fairly clear and straightforward. I implemented those, and a couple of trivial

Hi All, I''m a big user of the LARTC document but am currently stuck with a question around section 4.2 (http://lartc.org/howto/lartc.rpdb.multiple-links.html) in relation to "Routing for multiple uplinks/providers". I''m wanting to do a similar setup to the diagram where I have - lets just say for the moment - two uplink providers where I want to route over two

Hi. I´m making an script for load balancing of two cablemodems internet connections toward my LAN. The problem is that when I try to ''equalize'' the the two internet connections with the weight=1 it doesn´t work. On the other hand, if I put 5 and 5 it works, but not at 100%, it does intermittlently, some times works and others don´t. example: ip route add default equalize\

i´ve been searching for a load balance solution since a month ago... what i can say is that it simply doesn´t work. I was unable to find one guy that did it with sucess. When "load balance" is the subject of the message on the list, the message is simply ignored. So... if it doesn´t work... why LARTC don´t delete it from the HOW TO and answer us with some "it simply doesn´t

I am setting to a shorewall system with 4 NIC''s as per the outline specification below. Can anyone please have a look and let me know what I have missed and what I have got wrong as I want to take this system live ASAP but do not want to kill internet access and the hosting for too long ! I have listed below the system outline & have attached the config files that I have changed, if

Hello all, I have a linux router with 2 interfaces(eth0 - ISP and eth1 - LAN). I''ve established a VPN connection(openvpn) over eth0 with a friend of mine => tun0 interface. I want half of my LAN to have Internet access through the eth0 interface and the other half through the tun0 interface. I''ve set up a script like the "load balancing split access" instructions

Hello Im having a problem similar to sawar Here is my configuration --------------eth1---192.168.1.128---------- -------------192.168.1.1 ISP router 1 | my | ---Eth0---192.168.10.157----| | | linux |

FlacNetLib was by far the most useful code reference. if you dont know object oriented programming then you need to muddle through libFLAC as i havent seen any other implementation that isnt OO. -Gravis On Sun, Nov 4, 2012 at 1:16 PM, Serban Giuroiu <giuroiu at gmail.com> wrote: > Hi, Gravis. > > I'm trying to build a FLAC encoder from scratch. Besides the official format

provide me complete detail of your linux box like firewall script (iptables script), kernel''s .config file, multigatway file (i.e. /sbin/ip ....... commands file) so i can check and try to resolve your issue. sonu.... --------------------------------- Do you Yahoo!? Everyone is raving about the all-new Yahoo! Mail Beta. _______________________________________________ LARTC

Hi, I configured a router box to use 2 providers, as described in the HOWTO. (Apendix 1) I want to use both links to reach a single smtp server. As I read in the kptd and in some old messages of this list, doing a SNAT in the postrouting chain comes _after_ the routing desision. So I guess the following lines I''m trying to use are wrong. (See Apendix 1) What can I do to have multiple

Hi. Contents: 1) Introduction 2) 2 Questions * Introduction: I used this HOWTO to use multiple providers. http://lartc.org/howto/lartc.rpdb.multiple-links.html The box is a load balancer, using the Linux Virtual Server. We have a problem with lost connections, and it seems you get issues when you combine this setup with DNAT [1]. The proposed solution [1] is to use these rules to mark

Next week I''m replacing my single SDSL connection with two ADSL connections. I''ve got a plan for dealing with this, but I''d like any thoughts on potential problems I might run into. My goal is not to load balance the bandwidth (yet), but I do want to run all traffic through a single router. At the moment this router only has one ethernet port for both of the ADSL

Hi, I read the howto of iproute, I have the same case with HOWTO, the difference is that the whole incoming traffic goes through interface 0, the other difference is that I do not want to balance the out going traffic, because I have specific networks to take it throughout another interface. Mi Case IF1 --> Input and Output IF2 --> Only aoutput for three Network I need Help, How can I

Hi, I''m with a problem here on configuring our server to use multiple uplinks with different providers. The packet goes though on my way, but there is some lost packets that I don''t known where it''s going and causing my link to goes slow and stop sending/receiving data. Here i''m listing the route tables and the rules. It''s only for 1 IP.

Hi! I had two uplinks till today. We stopped one of them today, so i thought i could share my experience. (it is maybe useful for somebody) I hadn''t managed to configure it using a LARTC howto, but the Nano-howto (http://www.ssi.bg/~ja/nano.txt) and julian''s kernel patches. I had some problems with icq connections, because it is a two step connection (It is just theory). 1.

Hi folks, i spent my whole day trying to set up my linux router using load balancing with multiple uplinks. I mainly focused on the nano howto, but somewhere I have a big mistake within my head. Basically the load-balancing is working, but not on a per-connection basis - just on a per packet basis. Practically this is not usable of course <g> But as far as I understood it should work..

For easy reading: http://www.karthaus.nl/r/ Hi, We used to have 1 single ip range (1.1.1.0/24) that had one uplink to a = switch of the colocation provider. Recently we got a second range 2.2.2.0/24 and a redundant uplink = directly on two routers. But our switch does not have spanning tree = protocol support so we cannot use them redundantly. We have set up the switch to have a vlan for both

I am hoping that someone with more experience and knowledge than I can assist me in finding a solution ;) We have a RedHat AS4 box with 5 interfaces. Two interfaces serve two different networks and two interfaces connect to two different uplinks. The fifth interface is our management interface. Since a picture is worth a thousand words I attempted to come up with a diagram:

https://bugzilla.netfilter.org/bugzilla/show_bug.cgi?id=452 Summary: DNAT to internal network don't work with source routing and 2 uplinks Product: netfilter/iptables Version: linux-2.6.x Platform: i386 OS/Version: Debian GNU/Linux Status: NEW Severity: normal Priority: P2