similar to: strict priority

Hello, I am trying to mess with a prio type qdisc, and must be missing something. Here''s my sample code: tc qdisc add dev eth0 root handle 1: prio tc filter add dev eth0 parent 1:0 prio 1 protocol ip u32 \ match ip dst 208.0.0.0/8 flowid 1:1 tc filter add dev eth0 parent 1:0 prio 3 protocol ip u32 \ match ip dst 0.0.0.0/0 flowid 1:3 I would assume that any traffic going to

I can use DSMARK to mark on the Egress side. Is there a way to mark/change the DSCP value of an incoming packet on the ingress side? Thanks. Jon Flechsenhaar Boeing WNW Team Network Services (714)-762-1231 202-E7

Hi! I am studying HTB. I used the topology showed below: 10.1.0.1 ------ 10.1.14.25 (eth1) / 192.168.10.10 (eth0) ----- 192.168.10.11 (host 1) (router) (host 2) All machines use Debian Etch. Has a Iptables masquerading rule to eth1 in the router machine . The NICs are 100 Mb/s. The host 1 has Apache 2 and a file with 670 MB (CD ISO image) to download. When I used

Hello, I''m using a script with tc, to limit my outgoing traffic : tc qdisc add dev eth0 root handle 1: htb tc class add dev eth0 parent 1: classid 1:1 htb rate 500kbit burst 6k tc filter add dev eth0 parent 1: protocol ip prio 1 u32 match ip dst 172.28.54.9 flowid 1:1 I want to test bandwidth with iperf to see if limitation is correct. Sometimes, I get correct measure for certain rates,

Help! I tried nearly everything I could and still was not able to get IE working with wine 0.9.19. Manual install using App DB, winetools, ies4linux, etc... everything fails, with different problems and error messages of course. It's really frustrating. Is there a way to install IE that actually works ?

Dear all, I''m making a script to implement DiffServ policies with HTB. Here it is : if test $1 = "help" -o $1 = "h" -o $# != 5 then echo "usage: ds.sh <DEVICE> <DS_RATE> <EF_RATE> <AF_RATE> <BE_RATE>" exit fi DEV=$1 DS_RATE=$2 EF_RATE=$3 AF_RATE=$4 BE_RATE=$5 sync tc qdisc del root dev $DEV tc qdisc add dev $DEV root handle

All: I have been told that HTB_HYSTERESIS might have some effect on rate calculations. This file is usually in /usr/src/linux/net/sched/sch_htb.c. If I change this file I have to re-compile. I am not quite sure how to do this. Can someone list the steps necessary to re-compile or point me to a doc that explains how to do so. Thanks. Jon Flechsenhaar Boeing WNW Team Network Services

Hi to all I am studying HTB on LARTC how to. I realize a simple configuration on router: tc qdisc add dev eth0 root handle 1: htb default 30 tc class add dev eth0 parent 1: classid 1:1 htb rate 3mbit burst 15k tc class add dev eth0 parent 1:1 classid 1:10 htb rate 2mbit burst 15k tc class add dev eth0 parent 1:1 classid 1:20 htb rate 1mbit burst 15k tc qdisc add dev eth0 parent 1:10 handle 10: sfq

Hi there! I''ve using HTB for a while and now I an faced with a ''problem''. How hierarchical is HTB? Let''s say I have this 3 layer HTB setup: root class 1: (rate=100, ceil=100) 1: children classes 1:10 (30,100) and 1:20 (70,100) 1:10 children classes 1:100 (10,100) and 1:101 (20,100) 1:20 children classes 1:200 (30,100) and 1:201 (70,100) I managed to have

Hello - What I want to do seems very simple - I want to make sure any H.323 traffic gets processed before anything else entering or leaving this network. The network has a videoconferencing device on the LAN at 192.168.16.4. A Linux firewall NATs an external IP Address to this internal address and I have appropriate SNAT and DNAT rules that work. The NAT and connection tracking rules all work

Hey everyone, For some reason my htb configuration isn''t allowing any class to burst up to its ceiling ever, even when the link is only being utilised by one class that class only ever gets its assigned rate and exactly that assigned rate... The hierarchy I have is 1: at the root with no default, then 1:2 and 1:3 under that, both with assigned rates, then 2: and 3: under those

Hello, I use HTB with linux-2.4.20-ac1 and iptables-1.2.7a (pathced for IMQ). I configured one HTB qdisc on an IMQ device. This qdisc has some classes (about 5) and all of the classes has qdisc pfifo. I sometimes got out from my linux (while I was working) and I found in logs: Dec 4 11:49:27 core kernel: HTB init, kernel part version 3.7 Dec 4 11:49:28 core kernel: HTB: quantum of class

Hello everyone! I''m simply trying to put a PRIO inside an HTB (used to throttle). I''ve got interactive traffic on the network that I want to give priority (VoIP + Citrix + Video). I''ve used the filters in a CBQ script fine, but am having trouble adjusting them to this setup such that they properly assign the traffic. tc qdisc del root dev $e tc qdisc add dev $e

I''m streaming audio over a WAN that is 1.5Mbit/s. The audio has to go both ways and can be over tcp or udp. The manufacturers recommend udp as it has less overhead but has a higher chance of dropping out. The audio requires 130-200kbit/s in each direction for a combined 260-400kbit/s. I have two transparent bridges on either side of the WAN to do traffic control. I split it so

Dear all, I am facing problem in restricting upload traffic on fake ip address 10.0.0.0/8 network. I can easily restrict upload traffic on my real ip address. eth0 --wan port connected to internet eth1 --lan port connect to local network my script on eth1 is working properly bcoz it is for downlink traffic this is the script which is having problem.

Help me  ... I try use the tc filter, but seems he doesn''t work, I already reconfigured my kernel ( 2.4.32 ) with all options related a QOS enabled ( like modules ) and nothing happens. I get the tc tool from HTB source package, well  this is my set : eth0 is my internal NIC. tc qdisc add dev eth0 root handle 1: htb default 12 tc class add dev eth0 parent 1: classid 1:1 htb rate

Help me  ... I try use the tc filter, but seems he doesn''t work, I already reconfigured my kernel ( 2.4.32 ) with all options related a QOS enabled ( like modules ) and nothing happens. I get the tc tool from HTB source package, well  this is my set : eth0 is my internal NIC. tc qdisc add dev eth0 root handle 1: htb default 12 tc class add dev eth0 parent 1: classid 1:1 htb rate

Hello all, Please could someone help me with this, I have been trying for days to get this to work. I would like to have BE, AF & EF classes with HTB qdisc. I can''t find any scripts online where this has been done. If I enable this filter: #tc filter add dev eth0 parent 2:0 protocol ip prio 1 \ #tcindex mask 0xf0 shift 4 pass_on then BE & AF classification seems to be fine but

Hi, I wanted to implement some QOS on my Linux Box with HTB, but after some time spend on the configuration and tests, I still don''t manage to have some correct results. Here are the details : -ROOT 2000 kbits -HIGHPRIO SUBCLASS 50 kbits prio 0 -SUBCLASS1 750 kbits prio 1 -SERVICE1 250 kbits prio 1

Hey, I have a problem adding a filter matching anything, here is my setup: ############### tc qdisc add dev eth0 handle 1: root prio tc qdisc add dev eth0 parent 1:1 handle 10: pfifo tc qdisc add dev eth0 parent 1:2 handle 20: tbf latency 50ms rate \ 128kbit burst 256kbit tc filter add dev eth0 protocol ip parent 1:0 prio 1 handle 666 fw \ flowid 1:2 tc filter add dev eth0 protocol ip parent