similar to: htb on Gigabit Interfaces

Apparently Verizon is blocking or changing packets on port 5060 so my softphone from my hotspot will not work. How do I set asterisk (11.23.0) to run default 5060 for all other devices I have - BUT for my software run on a different port like 5070? I'm using linphone and is easy to change the ports from 5060 to 5070 ( I think). Thanks, Jerry -------------- next part -------------- An HTML

Hi, I am trying to categorize the network traffic and to send it out across two different providers. For this I mark the packets in the firewall (in the PREROUTING chain of table mangle), and then use another routing table for the marked packets, which has a different gateway from the main routing table. Basicaly I am following the cookbook example in this page:

Hi Everybody in the list I have a situation like this ------ (IP1) linux |----eth0.40------ | router | | | box | (IP2) |------|Client Router ( Destiantion Net DNET) |----eth0.41------ | | /27 subnet ------ I just want to balance the load of bandwidth per packet based between the two vlan interfaces to Client Destination network

I am using the script below to simulate a very high bandwidth connection.I find that I could not turn the bandwidth knob up to 100Mbit.I have had a look at this generally,but could not find an answer.any help would much appreciated as i have spent a lot of time on this and have not found any answers anywhere. In my test,I have four network cards and their rate are all 1000Mbps. my scripts:

Hi I''m doing traffic shaping with tc on ''10.0.0.0/30'' and ''10.0.0.28/30''. I want to delete part of shaping rules on the fly. (see my configuration at the end of this mail) I wan''t to delete the shaping for ''10.0.0.0/30'' on the fly while still keeping the shaping for part ''10.0.0.28/30'' running. When I for

hi list, oh it''s not really a problem. Each time i fire shorewall, i run a custom iptables script: (for the openvpn machines to have route back from my bridge/fw - $SOURCEIP is the ip of my OpenVPN/Fw/bridge) iptables -A POSTROUTING -t nat -s 10.8.0.0/16 -j SNAT --to-source $SOURCEIP i wish to better integrate it within shorewall, so is there any config files that could achieve the

Hi I have been playing with tc. I''m using htb and sfq. I tried to setup shaping of every ip address within a /20. I found that there must be an upper limit of about 2096 on the number of rules (classes, qdiscs or filters). I was testing a /20 which gives 4096 classes, qdiscs and filters. I''m using hashkey to optimize processing of frames. When executing the script below - it

Hi, I'm currently working on something quite ugly. We have a WindowsXP Home system here that is used as a storage server. Windows XP Home restricts the maximal user count to 5 users at a time that can connect to the network share. My boss doesn't want to delete winblows because he feels confident with it (except from the limitation) so a native samba server isn't possible. A

hi list, any idea how i can transcribe this simple iptables script to shorewall config? wich files should be modified ? iptables -A POSTROUTING -t nat -s 10.8.0.0/16 -j SNAT --to-source $SOURCEIP

Hi, I've a few working asterisk servers, all seeing the same symptom, but they are all based on the same configs. A SIP inbound INVITE message is coming in to an extension (not a peer) eg 555 at ourserver.com A tcpdump clearly shows the INVITE coming in, but asterisk seems to be ignoring it (theres no reply outbound packet). All the source/dest IPs and ports look good. A

Hello, my name ist Robert. I just wanted to know if there are any Plans for implementing a Log Rotation (e.g. daily base) or dump rotation (e.g. session based). A feature like this is not only needed for easier organisation of Archives but for comply with the german GEMA laws. The so called GEMA, states that (the System Administrator) should keep a copy of alle Shows for at least a month due to

Hi all, Thank-you to all the developers for rsync. It is very well done. I have rsync running on various platforms connecting to the same server and all is good. Except for 1 Win2000 Prof. server. I backup several directories with various permissions and users successfully. However, there are 2 directories that even though the permissions are the same as other directories that are

Hi, I read the news about Tom Steps quit. I use shorewall for some days now and as many people I ike it very much. I asked Tom in a personal mail, what could be done to continue the project and he told me I had to subscribe to this list. My ideas where: a) Mirroring the site b) I would like to study the code and help c) I am studying computer science and I could ask some teachers and friends

Hi, I use shorewall-4.5.4 + lsm-0.143 and it does not seem to work as expected... When all providers are up, everything seems fine. When one goes down, lsm says "link <provider> down event"... and it seems ok but we then experience some problems such as a few unreachable sites, DNS problems... If I remove the downed provider from all confs and restart, everything works again.

On 4/8/2019 4:55 PM, @lbutlr via dovecot wrote: > On 8 Apr 2019, at 16:35, Shawn Heisey via dovecot <dovecot at dovecot.org> wrote: >> I would like to create a sieve rule where I do a regex match on ALL headers, not a specific header. > > This is a really bad idea. Headers can be quite long, contain data that you do not have control over, and checking all headers will be very

Hi Gang To increase security against phished passwords and similar attacks, we consider offering customers to define IP ranges (or GeoIP locations) from which their dynamic registrations are being accepted. I can already look at the source IP in the dial plan, so no issue with validate an INVITE against a source IP. But I would also like to prevent registrations from outside of this

On Mon, 8 Apr 2019, @lbutlr wrote: > Really? Where outside the Received headers do IPs appear in your email headers? Well, let's see. Running a rough grep on 270-message spam folder # grep -E '^[-A-Za-z0-9]+:.*[^.0-9]{0,1}[0-9]{1,3}\.[0-9]{1,3}\.[0-9]{1,3}\.[0-9]{1,3}' ~/mail/FN | sort -u -k1,1 -t: Authentication-Results: spf=fail (sender IP is 52.233.28.167) List-Help:

Hello, Marvel Yukon Gigabit Ethernet is supported by CentOS ? -- -- Devel in Precio http://www.pas-world.com

Hello all, I want to learn about requirements if I want to protect gigabit network with ipfilter as transparent firewall. Which type of hardware is required to install FreeBSD + ipf (as transparancy ) . We use 3 gigabit ethernet to protection which type of gigabit ethernet carts are powerfull. Also, what about the NMBCLUSTERS , IPSTATE_SIZE and IPSTATE_MAX in ip_state.h. I want to collect all

Hi all, I am notice strange behaviour of samba in our mixed fastEthernet/gigabitEthernet enviroment. First of all let me to describe our situation. We have a samba server running debian unstable with 2.6.3 kernel installed. Server has a gigabit copper connection (tg3 driver) to the 100/1000 Megabit switch (3COM 4228G). Client is a WinXP/Linux workstation connected by ordinary 100 Megabit