similar to: xapi + ubuntu 12.04 out of memory crash

Package: xcp-xapi Version: 1.3.2-8 Severity: important During startup /etc/init.d/xendomains script is called. That script is installed with xen-utils-common witch xcp-xapi is depends on. That script calls /usr/sbin/xen as xen list &> /dev/null This 'xen' seems to call xapi: xen list ^Z [1]+ Stopped xen list root at lab-xh3:~# ps f PID TTY STAT TIME

Package: xcp-xapi Version: 1.3.2-8 Severity: important Tags: patch Found race condition (specific only to slave hosts): xcp-xapi can start earlier than xcp-networkd due lack of dependency in init.d script. Syptoms: After reboot slave's xcp does not work: xe (anything): The host failed to acquire an IP address on its management interface and therefore cannot contact the master. log:

Package: xcp-xapi Version: 1.3.2-6 Severity: important Configuration: Two xcp-xapi hosts (default sid/xcp-xapi installation) in single pool. Network backend is bridge. After migration of 'idle' (doning nothing) virtual machine it stops to reply to ping for long time. AFAIK that caused by mac-learning table on upper level (hardware) switch, which route all frames to wrong port

Package: xcp-xapi Version: 1.3.2-6 Severity: normal After some time of rebooting and toolstack restart found very funny output in 'xe pif-lis': xe pif-list params=currently-attached,device device ( RO) : vif2.0 currently-attached ( RO): false device ( RO) : vif211.0 currently-attached ( RO): false device ( RO) : eth1

Good day. Which ports are used by xapi? I suddenly found it using tcp/13993 and I''m slightly concern about possible collision between xapi and my own application, running on dom0 on XCP... Thanks. --- wBR, George. _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users

Package: xcp-xapi Version: 1.3.2-6 Severity: important I done normal reboot: xe host-disable host=this_host xe host-reboot host=this_host After reboot host stays in 'disable' state and when I've tried to make it enable I got: xe host-enable uuid=ab523ee3-0546-5400-e2db-32f340292fff The specified host is disabled and cannot be re-enabled until after it has rebooted. host:

Package: xcp-xapi Version: 1.3.2-9 Severity: normal Function wait_for_xapi in /etc/init.d/xcp-xapi does not work as intented. Symptoms: (on slave) /etc/init.d/xcp-xapi restart [....] Restarting The XenAPI server: xapiThe host toolstack is still initialising. Please wait. Cause: Line 'xe pif-scan host-uuid=${INSTALLATION_UUID}' called before xapi is fully synced with master.

Package: xcp-xapi Severity: important The README doc mentions: 4/ Configuring Xen and XCP -------------------------- 4.1/ Switch using xl instead of xm and xend to control Xen As of writing, you should do that: sed -i "s/TOOLSTACK=/TOOLSTACK=xl/" /etc/default/xen Where as the init script checks for: # Exit cleanly if TOOLSTACK != xapi if [ "${TOOLSTACK}" !=

One of the cluster nodes (XS 5.6 SP2/not master) became unresponsive to XAPI calls being sent from a CloudStack management server. In the past, a simple xe-toolstack-restart would do the trick but the script timed out while restarting the XAPI daemon. I found the process and first tried to use a simple kill command but the process was in a "defunct" state. I tried a kill -9 but no joy.

Package: xcp-xapi Version: 1.3.2-6 Severity: normal Tags: upstream /usr/lib/xcp/bin/xe-edit-bootloader failing with following message: /usr/lib/xcp/bin/xe-edit-bootloader -u 19f66083-e776-70d1-1808-3712688ad138 Creating dom0 VBD: 0fdb952e-92ff-4b53-dd49-8d54b2268787 Plugging VBD: Waiting for /dev/sm/backend/4c15ea03-5d70-938e-8265-d5424c0fda5e/963afb9a-9ceb-410f-8554-8be9fb70e7e0: . done

Package: xcp-xapi Version: 1.3.2-6 Severity: minor Tags: upstream If xe pif-configure-ip called twice with different IP, it did not remove old IP from interface (but didn't store both addresses in database). (Checked for management interface) Steps to reproduce: xe pif-reconfigure-ip uuid=... ip=IP1 .... xe pif-reconfigure-ip uuid=(same) ip=IP2 ... 'ip addr show' shows both

Package: xcp-xapi Version: 1.3.2-8 Severity: minor During upgrade from 1.3.2-7 to 1.3.2-8 got follwing message on slave host (upgrade was simulatanious on slave and master): ... Setting up xcp-xapi (1.3.2-8) ... The server failed to handle your request, due to an internal error. The given message may give details useful for debugging the problem. message: INTERNAL_ERROR: [

Package: xcp-xapi Version: 1.3.2-6 Severity: minor Tags: upstream Builin utility for lowlevel vm boot repairment xe-edit-bootloader contains wrong path to xe. IS: XE="/usr/lib/xcp/bin/xe" MUST BE: XE="/usr/bin/xe" -- System Information: Debian Release: wheezy/sid APT prefers unstable APT policy: (500, 'unstable') Architecture: i386 (i686) Kernel: Linux

Package: xcp-xapi Version: 1.3.2-7 Severity: normal xcp-xapi fails to eject host from pool with following error: xe pool-eject host-uuid=a6806a39-442d-f17d-b7a0-59161d18f56f WARNING: Ejecting a host from the pool will reinitialise that host's local SRs. WARNING: Any data contained with the local SRs will be lost. Type 'yes' to continue yes The server failed to handle your request,

Package: xcp-xapi Version: 1.3.2-6 Severity: important Tags: upstream xe vm-memory-target-set does not write new target to /local/domain/ID/memory/target. Balloon in guest domain is expecting this value to be changed to do selfballooning. This breaks 'dynamic memory control' feature. Steps to reproduce: 1) Setup any PV virtual machine with static-memory-min < static-memory-max 2)

Package: xcp-xapi Version: 1.3.2-11 Severity: normal xe host-set-hostname-live host-uuid=68878163-7c93-17af-7911-5a2726fefc66 host-name=xapi-xh3 The server failed to handle your request, due to an internal error. The given message may give details useful for debugging the problem. message: Subprocess exitted with unexpected code 2; stdout = [ ]; stderr = [ sed: can't read

Package: xcp-xapi Version: 1.3.2-6 Severity: normal Tags: upstream Normally (in 'iso-based' XCP) is possible to attach VDI to dom0. That operation usually looks like: xe vbd-create vdi-uuid=... vm-uuid=(dom0 uuid) device=N xe vbd-plug I done those steps in xcp-xapi and got success (no error), but no xvd* device found. Here operations log: # xe vbd-create

Package: xcp-xapi Version: 1.3-15 Severity: normal My packages were initially installed from the deb repository at download.xensource.org. Eventually, I upgraded them to the debian repository ones. Right now, xcp-xapi fails to start with the following messages. lnx200-39:~# /etc/init.d/xcp-xapi start Error: Connection refused (calling connect ) lnx200-39:~# -- System Information: Debian

Package: xcp-xapi Version: 1.3.2-6 Severity: normal Tags: upstream vbd plug to PV domain cause following error: The server failed to handle your request, due to an internal error. The given message may give details useful for debugging the problem. message: the device disappeared from xenstore (frontend (domid=4 | kind=vbd | devid=51760); backend (domid=0 | kind=vbd | devid=51760)) (same error

Package: xcp-xapi Version: 1.3.2-15 Severity: normal I am trying to pass an SRIOV virtual function in a virtual machine but the attempt fails with the following errors shown in the xcp-xapi.log [20130829T19:29:17.909Z|debug|sriov1|314 UNIX /var/lib/xcp/xapi|VM.start R:9e8e10bd31bb|pciops] PCI devices from other-config:pci to attach: 0/0000:04:00.1 [20130829T19:29:18.012Z|debug|sriov1|314 UNIX