similar to: Ipfw config

Hi, I'm having lots of difficulties with BCM5719, which is the default network card of HP Proliant DL 360 G8 servers. I can get a few ping replies before I get a couple of these: bge0: watchdog timeout -- resetting bge0: watchdog timeout -- resetting Then everything hangs. Can not log in using ssh.

I'm experiencing similar problems with a 3C996-T under 4.8-REL. In particular, connecting a 4.8-REL machine to a 5.1-REL machine leads to some interesting situations: I can do simple pings across the link, but ssh fails, and heavy pings crash the 4.8 machine. Similarly changing the interface configuration with ifconfig tends to crash the 4.8 machine (mtu, link0, up/down, etc). The

Hi. I got this on today's RELENG_6 with Broadcom BCM5722 A0, ASIC rev. 0xa200. >From dmesg (bge related): bge0: <Broadcom BCM5722 A0, ASIC rev. 0xa200> mem 0xe8400000-0xe840ffff irq 16 at device 0.0 on pci2 bge0: firmware handshake timed out, found 0x4b657654 bge0: firmware handshake timed out, found 0x4b657654 bge0: EEPROM read timed out bge0: failed to read EEPROM device_attach:

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hello All, I have had a problem detecting the network card on my notebook when ACPI is enabled for a year. The problem still exists in 7.1-RELEASE. with ACPI: ... bge0: <Broadcom NetLink Gigabit Ethernet Controller, ASIC rev. 0xb002> irq 17 at device 0.0 on pci8 bge0: 0x10000 bytes of rid 0x10 res 3 failed (0, 0xffffffff). bge0: couldn't

Hi all, I installed 2009.06, xVM and happily installed a domU with no issues. I just did this through the virt-manager GUI, and kept it as simple as possible. Later I installed and booted a zone with very simple and standard configuration. My existing xVM virtual machine did not immediately stop working, or have any interruption at all. But, I can no longer create new virtual machines, or even

Hi, this server, a Dell R720 has 4 bge on board, Broadcom NetXtreme Gigabit Ethernet, ASIC rev. 0x5720000 bge0: APE FW version: NCSI v1.1.7.0 bge0: CHIP ID 0x05720000; ASIC REV 0x5720; CHIP REV 0x57200; PCI-E miibus0: <MII bus> on bge0 ... I have connected the ethernet to port labeled 0, but it appears as bge2, how can this be corrected? thanks, danny

Hi, I have a system with a 4.11 Kernel. Unless I'm doing something very wrong, there seems to be something odd with ipfw. Take the following rules: ipfw add 00280 allow tcp from any to any 22 out via bge0 setup keep- state ipfw add 00299 deny log all from any to any out via bge0 ipfw add 0430 allow log tcp from any to me 22 in via bge0 setup limit src-addr 2 ipfw add 00499 deny log

Hi, Can you tell why my vnic built on top of an aggregation of 2 NICs of 1 Gbit/s doesn''t report a speed of 2 GBit/s ? [root at nazgul /]# dladm show-dev bge0 link: up speed: 1000Mb duplex: full bge1 link: down speed: 0Mb duplex: unknown bge2 link: down speed: 0Mb duplex: unknown bge3 link: down speed: 0Mb

Hello! When my application opens a URL in Firefox with more than 257 characters, the URL is truncated and the message below. "Err: psdrv: PSDRV_PPDGetNextTuple Line too long." I noted that this limitation may be due to the following code. See line 00363. Code: 00354 /********************************************************************* 00355 * 00356 *

On 2020-04-01 15:12, Greg Troxel wrote: > D'Arcy Cain <darcy at VybeNetworks.com> writes: > But yet, new packets from that IP address reach asterisk. It seems > almost entirely clear to me that you have a firewall problem, not an > asterisk problem. This could well be but Asterisk is the only thing that continues to communicate. > I would test this out with a remote

On OpenSolaris 2009.06 I created a flow, half a dozen VNICs, and I set some properties, and everything was working, then I rebooted my system and everything disappeared from show-vnic, show-flow, and show-prop. When I tried to re-create the objects, dladm said they already existed. While I could not see the objects, I could delete them. Example: # dladm show-vnic # dladm create-vnic -l bge0

I opened a bug report earlier today but it doesn''t seem to have been added to the bugs database. I''m posting here in case one of the Crossbow developers might see it and confirm this behavior. Description Duplicate packets are generated whenever an aggregate is introduced into the network configuration. We''ve ruled out switch ports and physical bge interfaces as

Can you post your Tinc configuration too? El lun., 30 ene. 2017 a las 11:42, Dave Albert (<dave.albert at gmail.com>) escribió: > Here is an extract of my current iptables that are not working: > > iptables -L -n -v > > Chain INPUT (policy DROP 8 packets, 1120 bytes) > pkts bytes target prot opt in out source > destination > 0 0

How do I create a vnic that represents the factory assigned MAC address of my physical nic? The bge device in my system (x2100) appears to support 4 MAC addresses. The driver reserves the first as the ''primary/default'' address and allows manipulation of the other three via the MAC_CAPAB_MULTIADDRESS interface. I''d like to use vnics on this system, as I have Xen guest

Howdy, I just finished reading through the Crossbow presentation: http://blogs.sun.com/sunay/resource/crossbow.pdf And have one question. If you create a virtual NIC with dladm: $ dladm create-vnic -d bge0 -m 0:1:2:3:4:5 -b 10000 1 Can you then add vnic1 directly to the zone? e.g.: zonecfg -z zone1 zonecfg:zone1> create zonecfg:zone1> set zonepath=/zones/zone1 zonecfg:zone1> add net

Well this is new. I haven't a clue what Dell has done on this R620, but this popped up today after I did a boat load of BIOS updates and tried to install stable/9 from our yahoo tree. If anyone sees the obvious solution here, I'd love to figure it out. found-> vendor=0x14e4, dev=0x165f, revid=0x00 domain=0, bus=2, slot=0, func=1 class=02-00-00, hdrtype=0x00, mfdev=1

Hello Samba List, I'm running a Samba 3.0.22 PDC on Solaris 9. Things got a bit peculiar when I added a 2nd network interface. The two subnets are a primary network that carries all the client traffic and a tape-backup/admin network that is not accessible to any clients, ie. aaa.bbb.ccc.241 - bge0 - primary network (address suppressed) 192.168.254.254 - bge1 - admin/backup network

Hi, I''m afraid I have some problems understanding how crossbow is supposed to work ;) On my machine (OpenSolaris, snv_111) I''m running VirtualBox with couple of linux / XP installation and additionally a zone with exclusive IP. My network configuration looks like this: [6]elsinore:~>dladm show-link LINK CLASS MTU STATE OVER bge0 phys 1500 up

Hi, how can ip instances be used with vlans ? Is that possible ? I don''t know how to configure this, if I only have one interface (e.g. bge0), and want to assign e.g. bge1000 to a zone. Any cookbooks available ? Thanks Detlef

Thanks a lot for your hints Pasi. Due to your suggestion I open a new thread here. I have tested with model=e1000 (HVMs). As HVM configs are identical (not iso images and LVM volumes) I guess it is a xen 4.1.2* issue .. or just involved domU OS-kernels (however as it is HVM it should not play any role) Tested and correctly working OSes (getting an IP address and pinging of