similar to: false low battery alarm

Hi, I'm running this command: # upsrw -s "battery.date=2013Jun7" -u ups-mon-IT "IT-APC-BOTTOMRIGHT at 127.0.0.1" Password: OK but I'm getting this listing: # upsc IT-APC-BOTTOMRIGHT at 127.0.0.1 battery.alarm.threshold: 0 battery.charge: 100.0 battery.charge.restart: 15 battery.date: 01/10/06 battery.packs: 000 battery.runtime: 1440 battery.runtime.low: 120

Hi, One of my APC devices reports: "unacceptable utility voltage rate of change". I believe it has something to do with input voltage fluctuating too fast maybe even beneath or over the input voltage thresholds. Should I worry about this? should I measure input voltage? (I suppose I'd need more than multimeter readings. Maybe an oscilloscope or a multimeter that can record

Thanks for the help, with the apcsmart-old driver it works again! Didn't notice my UPS is now so "old" ;-) Here is the output of upsc with apcsmart-old driver: battery.alarm.threshold: 0 battery.charge: 100.0 battery.charge.restart: 00 battery.date: 11/22/06 battery.packs: 001 battery.packs.bad: 000 battery.runtime: 540 battery.runtime.low: 120 battery.voltage: 53.73

On Jun 13, 2013, at 7:14 AM, ML mail wrote: > I just upgraded to Network UPS Tools upsstats 2.6.4 on Debian wheezy and noticed that it does not show the battery runtime anymore, the field is simply empty. It used to work before with NUT 2.4.1. Does anyone know what could be wrong? > > I am using the apcsmart UPS driver. The apcsmart driver was overhauled, and in 2.6.x, the previous

Hello, I just upgraded to Network UPS Tools upsstats 2.6.4 on Debian wheezy and noticed that it does not show the battery runtime anymore, the field is simply empty. It used to work before with NUT 2.4.1. Does anyone know what could be wrong? I am using the apcsmart UPS driver. Thanks, M.L.

Build from source, and done . . . wasting your time looking for a less out of date RPM is pointless. . . RPM, .deb, etc are almost always downrev. . . - Tim On June 10, 2017 2:06:42 PM CDT, Ben Kamen <ben at benkamen.net> wrote: >Hey all, > > I recently got an RMCARD205 for my Cyber UPS.... > >if I use no MIBS line in the config file, I get this: > > >> Network

I'm looking to buy some new UPSs and am thinking of parting ways with APC to explore other brands. Can anyone suggest another brand that handles doing calibration runs (or maybe another brand doesn't need them) that I can automate with NUT? Thanks, -Ben

On 12/27/18 8:09 AM, Charles Lepple wrote: > [...] That's Ben's point - either it is actual Ethernet (usually found > on an add-on UPS SNMP monitoring card, where the jack typically has > two status LEDs, one on either side of the notch for the modular plug > tab) that needs to go to another Ethernet jack on a NIC or a switch, > or it is a proprietary APC cable that

I am using NUT 2.6.5 as part of FreeNAS 9.2.0. I am using an APC Smart-UPS 5000 RM DL4 with a AP9619 network management card. NUT properly detects when the UPS goes on battery and initiates a shutdown after the configured time. The problem I have is that I am using a 208V unit on a 240V circuit. That means the normal state for the UPS is "TRIM". NUT doesn't treat that as an on line

> >> Maybe it's not a standard ethernet-to-UPS cable? > > That's Ben's point - either it is actual Ethernet (usually found on an add-on UPS SNMP monitoring card, where the jack typically has two status LEDs, one on either side of the notch for the modular plug tab) that needs to go to another Ethernet jack on a NIC or a switch, or it is a proprietary APC cable that

Hi debian jessie, nut 2.7.2-4 APC Smart-UPS 1500 connected through USB, running nut driver usbhid-ups This UPS powers my switches, internet connection and my monitor server that monitors this and my other UPSes + runs smokeping and nagios. But recently a powerloss seemed to have shutdown my monitor PC immediately, so it did not shut down the other servers cleanly. Power seem to be lost

On Aug 30, 2018, at 10:05 AM, Ong, Kevin wrote: > > The battery.mfr.date is actually the correct value I'm looking for. That is the exact date the battery was last replaced. And yes, it is the correct value displayed in apcupsd. I think we're on the same page for the battery date. What about the date of manufacture for the UPS - does 2012 seem reasonable? > > For the debug

On Aug 30, 2018, at 6:54 AM, Ong, Kevin wrote: > > I'm very sorry for the delay here, I've been very swamped with work. Here's the relevant information you guys need: > > "upsc APC_BR1500GI" output: https://pastebin.com/rH3W0dbz > "upsrw APC_BR1500GI" output: https://pastebin.com/tEWv8a3d > "upscmd -l APC_BR1500GI" output:

On 12/28/18 12:24 AM, David Melik wrote: > > On 12/27/18 8:17 AM, Charles Lepple wrote: >>> >>>> Maybe it's not a standard ethernet-to-UPS cable? >>> >>> That's Ben's point - either it is actual Ethernet (usually found on an add-on UPS SNMP monitoring card, where the jack typically has two status LEDs, one on either side of the notch for the

Hello, My APC Ups uses nut to manage all systems connected to it. But if online power failed until it shutdown, it not restart automatically after the power returned. It stay down until i restart it. When i execute the command: # upsc siUps1 it output me this: battery.alarm.threshold: L battery.charge: 018.0 battery.charge.restart: 15 battery.date: 03/31/07 battery.runtime: 120

On Jan 10, 2014, at 12:58 PM, Elliot Dierksen wrote: > I am using NUT 2.6.5 as part of FreeNAS 9.2.0. I am using an APC Smart-UPS > 5000 RM DL4 with a AP9619 network management card. NUT properly detects > when the UPS goes on battery and initiates a shutdown after the configured > time. The problem I have is that I am using a 208V unit on a 240V circuit. > That means the normal

On June 11, 2017 8:58:11 AM GMT+02:00, Manuel Wolfshant <wolfy at nobugconsulting.ro> wrote: >On 10 June 2017 23:26:47 EEST, Tim Dawson <tadawson at tpcsvc.com> wrote: >>Build from source, and done . . . wasting your time looking for a less >>out of date RPM is pointless. . . RPM, .deb, etc are almost always >>downrev. . . >> >>- Tim >>

Hello All I just discoverd NUT and I'm lovin' it. I was very successful getting nut to monitor a CyberPower UPS along with having a Linux slave for a friend of mine. I've come to a snag on my personal system though. I currently have two Back-UPS XS 1200 APC UPSs, and I'm seeing notifications of low battery on both units. Now, both units are not showing 'low battery' on

Lately I got (used) an APC Back UPS Pro 1000 and Back UPS NS 1080. I got an ethernet-to-USB cable from another UPS, but the Pro isn't detected (with usbhid-ups.) I haven't tried the NS yet but it seems to not be on the list though looks just like the Pro. Some months ago I was discussing setup of a Ferrups 700VA.  I got it to work only with a command in rc.local, but not automatically

On 03/04/17 17.24, Roger Price wrote: > On Mon, 3 Apr 2017, Jon Bendtsen wrote: > >> On 03/04/17 17.10, Roger Price wrote: >>> On Mon, 3 Apr 2017, Jon Bendtsen wrote: >>> >>>> Power seem to be lost immediately. >>>> But my APC Smart-UPS 1500 always reported everything OK. >>>> battery.charge : 100 >>> ...