Displaying 20 results from an estimated 1000 matches similar to: "TE820 hardware detection"
2013 Nov 14
1
recieve fax from PRI using spandsp 65% failure rate
Hi,
On one of our servers, we're having problems with incoming faxes. The connections come in through a PRI into a Digium TE820 card. 'fax show stats' yields the following:
FAX Statistics:
---------------
Current Sessions : 0
Reserved Sessions : 0
Transmit Attempts : 0
Receive Attempts : 740
Completed FAXes : 740
Failed FAXes : 486
Spandsp G.711
2010 Aug 23
1
Dahdi install gone wrong
The card you installed has FXO or FXS modules in it ????? are you getting
your lines directly from the telco co???
Doug D
On Mon 23/08/10 8:37 AM , Cassius Smith cassius at cassius.org sent:
* -----Original Message-----
* From: Todd Reese
* Reply-to: Asterisk Users Mailing List - Non-Commercial
Discussion
* To: asterisk-users at lists.digium.com [3]
* Subject: [asterisk-users] Dahdi
2014 Sep 03
0
Fwd: Identifying the multiple cards Digium TE820
Hello all!
We have 4 pieces TE820 cards in one server.
How we can define via settings on server, which card is number 1, which is
number 2, which is number 3 and which is number 4?
Because if later we add for example 2 cards more in the server, the cards
can change their position. for example card 1 will become other
number/position, and all dahdi/chan_dahdi settings will require
reconfiguration.
2013 Nov 23
1
DAHDI Missing '/sys/bus/astribanks/drivers/xppdrv/sync'
Hello group,
I am installing Asterisk on a new pc running Ubuntu 12.04.3 Server. ?I have dahdi-complete-2.7.0.1+2.7.0.1, and have tried 2.6.1 and 2.8.0-rc1 and 2.8.0-rc2. ?I am following along in the ASTERISK The Definitive Guide 4th Edition and on page 116 when I issue the command $ sudo /etc/init.d/dahdi start I get the following error:
Loading DAHDI hardware modules:
? ?wctdm24xxp: done
2008 Jan 22
2
TDM800P FXO problem incomming call
Dear all
I have asterisk 1.4.11 on Cent 4.3 i have faceing some problem i have TDM800P 8 port FXO card when i terminate PSTN line on this port can make outgoing call it is working fine but incomming call not handling ...when i call from outside to this line it is rinning but no one call land on my asterisk no debug in asterisk some time it land but most of time not .....
2007 Nov 01
1
AsteriskNOW and TDM800P
Hi all
I sold new TDM800P card with 8 FXO ports, someone know if can be use
this card on AsteriskNOW or trixbox?
What can i do for use this card?
Thanks.
----------
RafaelCanchola
Product Development Engineer,
FonetGlobal Inc.
rcm at fonetglobal.com
http://www.fonetglobal.com
Ph. + 52 800 022 10 21 ext. 214
+ 52 442 167 08 00
VoIP 523663899
d00d! cyberalph
-------------- next part
2013 Mar 09
1
Digium Wildcard TDM800P not working with DAHDI
Hello everyone,
How can I let Digium Wildcard TDM800P work successfully with DAHDI? Because
the Centos recognizes the card but I can't get the analog card working with
DAHDI.
Thanks in advance,
Gilberto
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.digium.com/pipermail/asterisk-users/attachments/20130309/d82ddd47/attachment.htm>
2008 Feb 14
1
Error checking asterisk method - suggestions?
Hi there dear users and dear developers of Asterisk!
I've got a maybe strange idea, let's see if you laugh or think it's reasonable J
I'm using Asterisk with Digium TDM800P cards with 24 lines (as an answering machine).
Each analog line can be reached through a phonenumber, since they are each connected to my telephone provider. Yes expensive I know J
The challenge:
I'd
2009 Jun 22
4
Different inbound routes for each interface on a TDM800P card.
I'm new to Asterisk and inherited this project so I apologize if this
question has been asked a hundred time before. I did start with Google
but I may not be asking the right questions, because I wasn't finding
any answers.
I have Asterisk 1.4.24 and FreePBX 2.5 running and using a Digium
TDM800P to interface with our six analog phone lines from the telco.
Currently I have a single trunk
2011 Aug 16
1
PRI Problem
I am having a problem with a new PRI turn-up on dahdi 2.5.0 and
asterisk 1.8.5 that I have not seen before. The PRI is setup as B8ZS,
ESF and the span shows up and ok. This PRI is merely a crossover T1
going into an old DC0 class 5 switch.
I am getting the following errors over and over again
[Aug 16 10:26:10] NOTICE[8002]: chan_dahdi.c:3043
my_handle_dchan_exception: PRI got event: HDLC Bad FCS
2011 May 12
1
Disabling echo cancellation by software
Dear, I have Asterisk 1.6 with an E1 Digium card with echo
cancellation module. So I need to use just the echo cancellation by
hardware and disable the echo cancellation by software. I use DAHDI
for my telephony hardware.
If the lines involved with echo cancel are:
In /etc/dahdi/system.conf:
echocanceller=mg2,1-15,17-31
In /etc/asterisk/chan_dahdi.conf:
echocancel=yes
echocancelwhenbridged=no
2009 Oct 15
1
sporadic one-way audio
We have several offices running Asterisk version 1.4.20.1, and OSLEC
with Rhino R4FXO-EC and one running a Digium TDM800P card for interface
to analog lines. All offices are running Snom 300 phones. Phones all
have static addresses and are on the same physical network as the server.
The problem we are having is that every so often we get someone calling
in where we can hear their voice,
2008 Apr 25
1
choopy audio when both side talk at the same time
Hi
I have a server with the last version of asterisk branches, zaptel
branches, 2 Digium Card with TDM800P
16 HPEC channels (Echo Cancelation), 40 Grandstream BT200 and 10
Grandstream GXP2000.
zapata.conf
echocancel=64
rxgain=0
txgain=0
when i place a call o receive a call, I finish a sentence i hear a
ssssssss, AND when the both side talks at
the same time i have choppy audio.
Any
2008 Jan 30
7
Problem with DTMF dialing
Hi all
I have a small problem here. I asked this question on another asterisk
mailing list, but nobody seemed to be able to help me there.
We are running
* Asterisk 1.4.17
* Libpri 1.4.3
* Zaptel 1.4.8
on a 1.6 dual core, 2GB ram and a digium TDM800P wildcard, hardware echo
cancelation and a quad FXO card.
We have 4 analog lines, one of which is a Cellphone line for least cost
2007 Mar 09
2
When to use Echo Cancellation cards?
In what scenarios non-Echo Cancellation cards (T1/E1/FXO) should be used ?
Don't all good and professional installations need echo cancellation cards?
Are there people out there with non-Echo Cancellation cards for T1 or 8 FXO
ports and who really don't have any echo issues and they are running serious
businesses?
--
Zeeshan A Zakaria
-------------- next part --------------
An HTML
2014 Feb 12
1
Problem/error with DAHDI tools 2.9.0.1
Hello,
Getting this error on dahdi_cfg. Reverting to 2.8 the error goes away:
*line 15: Unable to create 'dahdi_cfg' mutex.*
Is this a problem?
Thanks in advance.
Full detail:
[ebox]> dahdi_cfg -vvvvvvv
DAHDI Tools Version - 2.9.0.1
DAHDI Version: 2.9.0
Echo Canceller(s): HWEC
Configuration
======================
SPAN 1: CCS/ AMI Build-out: 0 db (CSU)/0-133 feet (DSX-1)
SPAN 2:
2016 Nov 11
3
dahdi_scan
lspci | grep Digium
03:05.0 Ethernet controller: Digium, Inc. Wildcard TE122 single-span
T1/E1/J1 card (rev 11)
dahdi_scan
So I have a card in a box - lspci shows it...
dahdi_scan reports nothing.
Is my card dead?
Jerry
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
2008 Feb 04
2
make dataframe from table
Dear R-experts,
I have got a dataframe:
data
ID disease
V1 V2
1 p1 1
2 p1 3
3 p3 3
4 p3 5
5 p5 1
From which I extract a usefull table: affect
affect
1 3 5
p1 1 1 0
p3 0 1 1
p5 1 0 0
I want to merge this with anotherdataframe:
age
p1 23
p2 24
p3 23
p4 11
p5 45
If have tried as.data.frame(affect) and other solutions to get the
following comment going:
2009 Feb 02
1
Preferred Clock
Hi,
We're running on a * 1.4.21 system. We run about 80 SIP Extensions, mainly
ATCOM phones (and a few Snoms - 300 and 360), and have an additional 80 IAX2
extensions to iaxmodem devices for fax2email. We are rapidly growing and
will be adding an additional PRI trunk and grow to about 150 SIP & IAX2
extensions towards the end of the year.
We have two Digium Wildcard TDM800P cards (8 x
2009 Jan 26
3
Digium TE220 card partially detected
Hello folks.
I've got a strange issue.
When I modprobe TE220 I do not see mesages like Launching card: 0 <..>
Setting up global serial parameters.
You can see how I loaded and unloaded the card for several times -
http://asteriskpbx.ru/pastebin/11
lspci can detect the card: 03:08.0 Communication controller: Digium, Inc.
Device 0220 (rev 02)
dahdi_hardware also:
astpbx ~ # dahdi_hardware