similar to: APC UPS: replacement battery always triggers shutdown

Arnaud, I was finally able to get back to this issue and would recommend adding these items to the FAQ #37 about recalibrating the UPS: 1a. It's important that the UPS be at 100% charge before starting the procedure; starting at lower will not work at all, not just produce inaccurate numbers. ? ? ? [I started the procedure when the UPS was at 91% charge. After that it would never report

Hi, I am trying to set up NUT on a mini-ITX system running OpenBSD 5.5. I have an APC Smart-UPS SC620 which runs perfectly well on Ubuntu, with nut-2.2.1. Ubuntu system uses ASUS motherboard. On mini-ITX system, I have Intel d2500cc motherboard with 4 serial ports. I've tested ports by connecting them with a null-modem cable and running cu in 2 terminals. Type in one terminal, output shows

On May 2, 2014, at 3:26 AM, Kastus Shchuka wrote: > Hi, > > I am trying to set up NUT on a mini-ITX system running OpenBSD 5.5. > > I have an APC Smart-UPS SC620 which runs perfectly well on Ubuntu, > with nut-2.2.1. Ubuntu system uses ASUS motherboard. > > On mini-ITX system, I have Intel d2500cc motherboard with 4 serial ports. > I've tested ports by connecting

On May 3, 2014, at 5:20 AM, Charles Lepple wrote: > On May 2, 2014, at 3:26 AM, Kastus Shchuka wrote: > >> Hi, >> >> I am trying to set up NUT on a mini-ITX system running OpenBSD 5.5. >> >> I have an APC Smart-UPS SC620 which runs perfectly well on Ubuntu, >> with nut-2.2.1. Ubuntu system uses ASUS motherboard. >> >> On mini-ITX system, I

Well, here's the tale: we got a "replacement kit" for some APC SmartUPS 3000 - rackmount UPSs. The "kit", costing about half of what APC is asking, is just the batteries, and you pull the tray out, open it up, and swap out the batteries. Except, I did this on one... and the replace battery light never went out. Not using apcupsd's apctest, not pushing the button. The

Hi there, I am using an old (really old) APC Smart-UPS 600. It worked fine under apcupsd but when I tried NUT it did not work. The error I was getting was: sudo /lib/nut/apcsmart -DDD /dev/ttyS1 Network UPS Tools (version 2.0.4) - APC Smart protocol driver Driver version 1.99.8, command table version 2.0 debug level is '3' Attempting firmware lookup Firmware: [D4] Not found in

2009/5/3 Thomas Juerges > -----BEGIN PGP SIGNED MESSAGE----- > Hash: SHA1 > > Hi Arnaud, > Hi Thomas, > I just checked the 2.4.1 version of nut and found that you forgot to add > my old UPS model (APC Smart-UPS 900). I guess it is because you were > busy at the time when I sent you the patch. So here it goes again. :) > uh, right sorry. I was pretty sure I applied

Hello, does any one know how to change the date of the self tests on APC UPSes ? I'd like to be able to choose the day and the hour so that it happens at office hours, in case of any problem... I've tried to do this by launching a test at a convenient time, but the self tests still occurs at the previous date and hour :-( Regards. -- Frantz de Germain D?partement Informatique UFR

I am having problems with mouse, keyboard and APC UPS. When attempting to start apcupsd I get the following error: Jan 8 17:42:06 Ace apcupsd[1606]: apcupsd FATAL ERROR in generic-usb.c at line 636 Cannot find UPS device -- For a link to detailed USB trouble shooting information, please see <http://www.apcupsd.com/support.html>. Jan 8 17:42:06 Ace apcupsd[1606]: apcupsd error shutdown

On Dec 4, 2014, at 5:30 AM, Frantz de Germain <frantz at info.univ-angers.fr> wrote: > Hello, > > does any one know how to change the date of the self tests on APC UPSes ? I'd > like to be able to choose the day and the hour so that it happens at office > hours, in case of any problem... > > I've tried to do this by launching a test at a convenient time, but

I believe some fixes were applied to the branch since your report (most visibly, about battery time settings), are you in position to test how it behaves now? :) Thanks in advance, Jim Klimov On Wed, Nov 22, 2023 at 3:20?PM Jim Klimov <jimklimov+nut at gmail.com> wrote: > Great! Thanks for the info, and hope the driver author can address the > nits (forwarding now...) > > Jim

I believe some fixes were applied to the branch since your report (most visibly, about battery time settings), are you in position to test how it behaves now? :) Thanks in advance, Jim Klimov On Wed, Nov 22, 2023 at 3:20?PM Jim Klimov <jimklimov+nut at gmail.com> wrote: > Great! Thanks for the info, and hope the driver author can address the > nits (forwarding now...) > > Jim

Here's an odd one: I installed apcupsd, and it works with most of our UPSs. I'd swear it worked on this one. Then I replaced the Gin-u-wine APC batteries, which were dead, with new ones, non-APC. They're just dumb batteries, no chips or whatever on them. If I hook it up using a serial cable, I can get info. If I hook it up the way I had it, with APC's weird USB cable - and this is

Jim Klimov <jimklimov+nut at gmail.com> > > I believe some fixes were applied to the branch since your report (most visibly, about battery time settings), are you in position to test how it behaves now? :) Hi: I got another ups for testing. so I test the new commit for both APC SRT3000XL and SMT2200RM2U. the results below: 1. I get the new attribute "ups.test.result" for

Jim Klimov <jimklimov+nut at gmail.com> > > I believe some fixes were applied to the branch since your report (most visibly, about battery time settings), are you in position to test how it behaves now? :) Hi: I got another ups for testing. so I test the new commit for both APC SRT3000XL and SMT2200RM2U. the results below: 1. I get the new attribute "ups.test.result" for

Hi, I have two types of UPS devices and one of them (APC) gave me a false "low battery" alert. I can't reproduce the problem... Also, there was nothing apparently wrong with the UPS at the time of the false alert. All I could do was grab the driver values within a minute after the "low battery" notification. These are the values: battery.runtime.low : 120

Hi there, Seeing an odd behaviour when running upsmon -c fsd to test my Raspberry Pi (running Jesse Lite) setup as a upsmon master, attached via USB to an APC Back-UPS XS1300. The Raspberry Pi is plugged into the Master outlet on the APC. The UPS clicks onto battery (and the fan spins up) for a few minutes, then resets, then repeats again, while finally remaining on AC power afterwards. The

Hi, I'm running this command: # upsrw -s "battery.date=2013Jun7" -u ups-mon-IT "IT-APC-BOTTOMRIGHT at 127.0.0.1" Password: OK but I'm getting this listing: # upsc IT-APC-BOTTOMRIGHT at 127.0.0.1 battery.alarm.threshold: 0 battery.charge: 100.0 battery.charge.restart: 15 battery.date: 01/10/06 battery.packs: 000 battery.runtime: 1440 battery.runtime.low: 120

Hello, I just buy a new UPS, the APC Back-UPS 950. In the back side it has a yellow plug that say "Battery Connector". If I connet it, the UPS works well, it switch on the green light "On Line". If I unplug ot it start to beep and it switch on the red light "Replace Battery". Need I plug the "Battery Connector"? Thanks and regards. -------------- next

On Dec 6, 2015, at 3:32 AM, Josu Lazkano <josu.lazkano at gmail.com> wrote: > > Hello, > > I just buy a new UPS, the APC Back-UPS 950. > > In the back side it has a yellow plug that say "Battery Connector". > > If I connet it, the UPS works well, it switch on the green light "On Line". If I unplug ot it start to beep and it switch on the red