similar to: Asterisk error message so uncommon, not even Google knows abuot it

Hi, We have got a new PRI card at one of our Office locations and now I need to install the the device on a remote server. Is there any way to know if the device is loaded already. When I give " cat /proc/zaptel/* " it returns the following. # cat /proc/zaptel/* Span 1: WCT1/0 "Wildcard TE122 Card 0" (MASTER) B8ZS/ESF RED IRQ misses: 2 1 WCT1/0/1

I am having a problem with a new PRI turn-up on dahdi 2.5.0 and asterisk 1.8.5 that I have not seen before. The PRI is setup as B8ZS, ESF and the span shows up and ok. This PRI is merely a crossover T1 going into an old DC0 class 5 switch. I am getting the following errors over and over again [Aug 16 10:26:10] NOTICE[8002]: chan_dahdi.c:3043 my_handle_dchan_exception: PRI got event: HDLC Bad FCS

Hi, On a Asterisk 1.8.12 system working OK for months (>100k calls proceed), users are complaining for bad audio. My setup is: PSTN <--E1/PRI ---> Asterisk <--- E1/PRI---> Siemens HiPath <---E1/PRI ---> PSTN asterisk -rx "dahdi show version" DAHDI Version: SVN-trunk-r10414 Echo Canceller: HWEC asterisk -rx "pri show version" libpri version: 1.4.12 A

Hi, I have been trying to get a Wildcard TE122 card running here the last couple of days. libpri and zaptel are all installed and configured to E1 specs. The jumper on the card is on, so configured for E1 (I'm in Norway). When running zttool, I get 'Alarms: RED' on the single card installed. Other information in zttool: Current alarms: Red Alarm Sync source: Internally clocked

I have recently built a single-T1 Asterisk box using an HP DL120G6 with a Digium TE122 card. I was finding that I was getting missed interrupts on the TE122, causing the driver to report that it was increasing latency. It kept doing this until the T1 did not work reliably. I tried my usual procedure of disabling the USB subsystem in the BIOS (or so I thought), but I found that the USB drivers

Does anyone know if the TE122 is recognized by any of the 1.2 zaptel drivers? It seems that 1.2.16 knows it not... :) Cheers, j

I have setup a asterisk with freepbx, a TE122 and i have an ISDN. My problem now is that callers are experiencing echo. checked on dmesg i saw this: # dmesg -c dahdi: Disabled echo canceller NLP because of CED rx detected on channel 2 i searched google but found no soolution and i have no idea what that error means. below are other details that might be of value. # dahdi_hardware

lspci | grep Digium 03:05.0 Ethernet controller: Digium, Inc. Wildcard TE122 single-span T1/E1/J1 card (rev 11) dahdi_scan So I have a card in a box - lspci shows it... dahdi_scan reports nothing. Is my card dead? Jerry -------------- next part -------------- An HTML attachment was scrubbed... URL:

What's the difference between the TE121 and TE122. I read the description on Digium's site and it isn't clear to me. Best regards, -- Guilherme Loch G?es Visite nossa loja virtual: http://www.shopvoip.com.br Not?cias e F?rum sobre VoIP com software livre: http://www.asteriskexperts.com.br -------------- next part -------------- An HTML attachment was scrubbed... URL:

I am trying to get a zaptel install converted to dahdi. I can get dahdi installed, and the pseudo device even shows up; however, dahdi show channels shows me nothing. There is a TE122 and a TDM800 in there, and neither show up. dahdi show status shows both cards, and dahdi tools show that the cards are there, working, and have no alarms. What am I missing? Michael Munger, dCAP, MCPS, MCNPS,

Just wondering how your experience is with HPEC, Is it just for analog interfaces or we can use it on TE122 as well? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20080214/3f0580f1/attachment.htm

Hello, I am installing dahdi on a machine lspci 00:00.0 Host bridge: Intel Corporation 3200/3210 Chipset DRAM Controller (rev 01) 00:01.0 PCI bridge: Intel Corporation 3200/3210 Chipset Host-Primary PCI Express Bridge (rev 01) 00:06.0 PCI bridge: Intel Corporation 3210 Chipset Host-Secondary PCI Express Bridge (rev 01) 00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI

Dear Sir/Miss: I'm very sorry to bother you,but I've found a bug in the Speex,Version 1.2beta1,and also I've have some questions. I'm deeply impressed by the work you have done in the coding and decoding of speech signal.But when using speex,I encoutered a bug,that is when in 32K mode,the window size is still 200 samples,but not 400 samples,the bug will bring the problem of

Dear friends, I have asked last few days about cross-random effects using PQL, but I have not receive any answer because might my question was not clear. My question was about analysing the salamander mating data using PQL. This data contain cross-random effects for (male) and for (female). By opining MASS and lme library. I wrote this code sala.glmm <- glmmPQL(fixed=y~WSf*WSM,

Dear, I have an Asterisk PBX with two E1 cards: Digium TE122 and Sangoma A101D. Sangoma card has SNMP support but Digium card has not, and also SNMP does't give me ral time information. Within CLI Asterisk I execute "dahdi show channels" but I don't get information about channels usage. What is the best way to have real time monitoring of E1 channels usage and status ???

Hi, I'm experiencing difficulties to get a B410P running with Asterisk 10.3.1 and DAHDI 2.6.1. Am I supposed to use DAHDI for this card and ISDN BRI for my country (Belgium)? thx, BC

Hello, I am having odd issues with a new PRI based installation. Outbound calls work for all numbers except those that terminate at Sprint! The telco is new to PRI (this is in the Caribbean) and say that Sprint is rejecting the calls, and asked for our PRI settings so they can work with their switch manufacturer. We are using the bare minimum default settings, but I can imagine that a

Hello, Currently my asterisk system pickup incoming call after 3 or 4 rings. How can I ask it to answer the call on the first ring? I put immediate=yes on /etc/asterisk/chan_dahdi.conf but result in no different. Thanks in advance :) BR, Anam -- Sent from my mobile device

Hello all, OS OpenSuSE 10.3 * ver 1.4.26.2 zaptel ver. 1.12 Digium TE122 I have a request for remote users to be able to dial through the system so that the sales managers can barge/chanspy on the sales force. I have the DISA part working with authentication(rather straight forward) but what I can not figure out is how to enable the supervisors to be able to barge on these calls. Is there a

Thanks, Eric. I just tried a hangup handler, but it's showing a similar problem: When the peer hangs-up, the hangup handler is not invoked and the caller channel remains open. same => n(callPeer),Set(GLOBAL(Peer${IndexIntoPeers}CurrentCallsCount)=$[${PeerCurrentCallsCount} + 1]) same => n,Set(CHANNEL(hangup_handler_push)=handleHangupByCallerOrPeer,doesntMatter,1(args)) same =>