similar to: dbcheck

Hi, I am experiencing a failure running virt-v2v to convert a Linux guest on an ESX host to a RedHat KVM hypervisor. The output with the failure follows. Any help/guidance is appreciated. [root at storage-024 ~]# virt-v2v -ic esx://<ip address>/?no_verify=1 -op transferimages --bridge br0 dev-03 > /tmp/virt-v2v.output error from Term::ReadKey::GetTerminalSize(): Unable to get

Hi, I migrate Xen4.0 to XEN4.1, and found XEN4.1 performance is not as good as 4.0.2. xm shutdown takes longer time, control thru libvirt take longer time, and since I''m testing PCI/VGA passthru, the "createdevice: pci" also take around 5~8 seconds comparing to 1 second in XEN4.0.2. below is my configuration, do you have any suggestions to make the performance better?

I have already posted another issue here<http://samba.2283325.n4.nabble.com/Samba4-Problem-with-Joining-Samba3-to-Samba4-AD-Domain-td4642466.html>that may be related the current issue I am having. I have Three Samba4 AD Domain Controllers, the first one installed that was the primary domain controller is the one having problem, the other two seem to be working OK. I discovered the problem

HI there. Probably my message is a bit off topic but I do not know where else I could be asking. . I'm running a linux terminal server with one client provided with a 3C509B ISA card. I boot the later with a floppy bootable rom image taken from http://www.rom-o-matic.net/ Everything is working just fine. I decided to try to set up a PXE network boot (I'll needed it for installing a

On 02/11/2014 04:45 PM, Cole Robinson wrote: > On 02/10/2014 06:46 PM, Chris Friesen wrote: >> Hi, >> >> We've run into a problem with libvirt 1.1.2 and are looking for some comments >> on whether this is a bug or design intent. >> >> We're trying to use migrateToURI() but we're using a few things (numatune, >> vcpu mask, etc.) that may need

Hi, We've run into a problem with libvirt 1.1.2 and are looking for some comments on whether this is a bug or design intent. We're trying to use migrateToURI() but we're using a few things (numatune, vcpu mask, etc.) that may need adjustment during the migration. We found that migrateToURI2() mostly works if we use XML created by copying the domain XML from the running instance

nobody any suggestions for me ? :-(( im running kernel 3.2. from backports. Greetz, Louis >-----Oorspronkelijk bericht----- >Van: belle at bazuin.nl [mailto:samba-bounces at lists.samba.org] >Namens L.P.H. van Belle >Verzonden: 2012-06-18 15:02 >Aan: samba at lists.samba.org >Onderwerp: [Samba] samba4 on debian squeeze > >hai, >? >Im trying to install

I could use some help debugging a bazaar PuppetDB problem. Exported resources seem to be working fine everywhere except for on the Puppet Masters themselves. Whenever I run the puppet agent on them everything seems to go fine and I see the catalog getting submitted to PuppetDB in the logs. However, when I run puppet on the node that should collect these resources they aren''t

Hello everyone. I apologize in advance if what I'm talking about here is obvious to all. I don't usually deal with SMB stuff. So, recently I was asked to implement "server signing = mandatory" for a SMB service that exposes only anonymous / guest shares. At first I tried with Samba 3.6.x and a Windows 7 client, but "net use" from Windows refused to mount the SMB

Hi, i recently updated our windows 2008 r2 servers to puppet 3.3.0 . Im getting the following error* (only on our exchange 2010 db servers)*ever since: LevelMessageSourceFileLineTimeerrCould not retrieve local facts: undefined method `gsub'' for nil:NilClassPuppet13.09.2013 15:12 CESTerrFailed to apply catalog: Could not retrieve local facts: undefined method `gsub'' for

Hey Richard, Could you share the following informations please? 1. gluster volume info <volname> 2. getfattr output of that file from all the bricks getfattr -d -e hex -m . <brickpath/filepath> 3. glustershd & glfsheal logs Regards, Karthik On Thu, Oct 26, 2017 at 10:21 AM, Amar Tumballi <atumball at redhat.com> wrote: > On a side note, try recently released health

On a side note, try recently released health report tool, and see if it does diagnose any issues in setup. Currently you may have to run it in all the three machines. On 26-Oct-2017 6:50 AM, "Amar Tumballi" <atumball at redhat.com> wrote: > Thanks for this report. This week many of the developers are at Gluster > Summit in Prague, will be checking this and respond next

Hi Karthik, thanks for taking a look at this. I'm not working with gluster long enough to make heads or tails out of the logs. The logs are attached to this mail and here is the other information: # gluster volume info home Volume Name: home Type: Replicate Volume ID: fe6218ae-f46b-42b3-a467-5fc6a36ad48a Status: Started Snapshot Count: 1 Number of Bricks: 1 x 3 = 3 Transport-type: tcp

Hi to all! I have a problem with a nvidia geforce 520mx [NVd0 generation card (0x0d9110a1)] i have on my notebook (samsung 3 series). In practice i'm not able to use it with bumblebee and bbswitch. The dmesg message is: [ 13.507435] nouveau 0000:01:00.0: power state changed by ACPI to D0 [ 13.507440] nouveau 0000:01:00.0: power state changed by ACPI to D0 [ 13.507448] nouveau