similar to: FreePBX: using context other than the default context and the generation for the configuration

Hi All; Using the FreePBX, after I added the extension from the GUI, I discover that it is automatically added in the extensions_additional.conf in the context [ext-local] and [from-did-direct-ivr] How I can change these context name? I need to determine this. How? Regards Bilal

Hello: We have a TDM2433E Digium Card (12 FXS, 12 FXO) and Asterisk 1.8.7.0 running. Everything seems to be ok but call transfers. This is the issue: *A, B, C and D are in FXS ports*. 1) A calls B. B anwers. 2) B tries to transfer the call to C dialing *2 (code for attended transfer). 3) A hears MOH. B dials number C. 4) Asterisk says the dialed number is incorrect or non existing. We tried

Hi All; When the call coming via the E1 dahdi and I handle the call (as first step) by exten => 5631040,1,Goto(OrangeCMG,s,1) it is not working and the call will be disconnected instead of queued. But, when I handle the call (as first step) by playing any sound file and then send for the queue, then it is working fine, WHY? exten => 5631040,1,Playback(WelcomeMessage) exten =>

Hi All; Again, the Cisco IP Phones 7942G and using Skinny: I upgraded the firmware to version 8.5 (skinny) and I am using skinny channel (chan_skinny) and the skinny.conf file. The phones are registering, but when we use them to place a call, we only hear tooooooooooo in the handset and we do not hear voice (even when we dial the digits, we only hear toooooooo .. but it dials and destination

Dear Tariq; About elastix.org, this can be use with Asterisk or it is coming as a complete IP Telephony, Call Center, IVR and Reporting? Because, I do not need to install another IP Telephony on the server which already has asterisk which is an IP Telephony, this will cause a problem in the service (for example, when listening for SIP port of 5060).

Hi All, I am trying to connect my asterisk box with freepbx to PSTN. I have purchased x100p FXO card and installed in my asterisk server. My freepbx detected the x100p FXO card and i can see the card specific details in command line. I have configured the following things. 1. OUTBOUND caller id and Dialing rules in Freepbx. 2. INBOUND route When i call to the PSTN number before

Hi All; Can anyone advise if using Cisco IP Phones in skinny protocol is fine or not? Or it is better to use it in SIP protocol? Regards Bilal

Hi I've been noticing an odd issue with our servers (1.4.17) where a large number of one particular customer's (we operate a hosted VoIP platform) calls go through a Local channel rather than the SIP channel and whenever this happens our asterisk CDR is recording a billsec value of 0. Our outgoing calls to POTS are sent through a separate carrier and we get a daily CDR off them in

Hi All; I installed Asterisk on a new Server, it is a Dell Server and has 4 Ethernet ports. I gave IP address 192.168.0.3 for one Ethernet port. I am able to login for asterisk using /usr/sbin/asterisk -rvvv and from there (in the command line) I can type a commands. I have an Polycom IP Phone that is able to register for other Asterisk boxes (and some of them is 1.8.3) but with this new

I am not proxying the media, but never the less I am forced to store the source media IP in my CDR, for regulatory reasons. Asterisk gets that information when the reinvite comes, but how do I store it? If I don't figure this out my next email will be from Federal Prison. Kindly help me stay away from those guys. Eventually we all need to save that information or we shall not be able to stay

Dear, I have asterisk 1.6.2.13 in a small hardware PBX (512 GB RAM and Celeron), and last days when I call from one extension to another of the same PBX after I dial the number the rings sound after 20 seconds. In the CLI log, when I debug the AGI, I see always goes good until dialparties.agi, and after that there are 20 seconds without any log, and so the ring sound. I've read

Hi, I've been meaning to fix my non-working paging feature here for a while, and I've just spent the last 5 hours looking at many, many web pages that all say the same thing. I am using Asterisk 1.6.2.18 and Polycom phones, both older (501 with "latest" legacy 3.1.7 firmware) and newer (335 and 650 with latest 3.3.1f). I have changed the correct values in sip.cfg like

I'm trying to decide if I need to open an issue for this or if it's just a misconfiguration issue of some sort. Here's the situation - yesterday morning, I downloaded asterisk 1.8.19.1 and installed it on a fresh CentOS 5.8 installation and got a shell of a basic asterisk install setup (minimum required configuration files, etc, with no dialplan or sip peers setup yet). In the

Hi Guys, Just did an Asterisk 1.6.x (repo install) and FreePBX (source install). When trying to dial a number, I get this: tel*CLI> Use of uninitialized value in hash element at /var/www/html/panel/ op_server.pl line 3367. Use of uninitialized value in concatenation (.) or string at /var/www/html/panel/op_server.pl line 3372. Use of uninitialized value in pattern match (m//) at

Hello, For those customers with only analog lines, who ask for fax2email and email2fax, whats the most reliable solution available and tested with Asterisk? Thanks -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.digium.com/pipermail/asterisk-users/attachments/20120529/3e28b56e/attachment.htm>

When I receive a call, I want to automatically park it from the dialplan so that I can retrieve it later. However, I don't want callers to be aware that they are being parked, so I want to play a ringing tone to the caller. Park() is supposed to be able to do this: Park([timeout][,return_context[,return_exten[,return_priority[,options[,parking_lot_name]]]]]) options r: Send ringing

NEWBIE alert: i'm a linux person, not an asterisk person so i'm certainly capable of handling any linux-flavoured solution you can suggest. here's a note i got from a local company i know (some proper names removed): ===== start ===== Now and again our ISP goes down and when it does give us a hicup, the Asterisk system shuts down (not very forgiving). When it shuts down our phone

Hey Guys! I am getting this wired error when i am calling IAX trunk. Everything works! but i want to get rid on these RED WARNING messages.. what is wrong here ? I have func_aes.so module loaded. also i remove and test but still same error. -Satish == Using SIP RTP CoS mark 5 -- Executing [7623 at from-sip:1] Macro("SIP/7527-0000000d", "orasebcamdial,7623") in

Can you say a Virtualized Asterisk with a PRI card! http://www.phoronix.com/scan.php?page=news_item&px=OTY0OQ Doug -- Ben Franklin quote: "Those who would give up Essential Liberty to purchase a little Temporary Safety, deserve neither Liberty nor Safety."

Hi List, I have another issue on allowing outgoing calls to PSTN on Asterisk via Avaya Phones, I hope that anyone could help me fix this issue: *When I dial through Avaya phone i just here a "good bye message" reply from asterisk server. And here is the log:* == Starting OOH323/(null)-b7db8aa0 at internal,s,1 failed so falling back to exten 's' == Starting