similar to: Tinc config

Hi, I have two tinc nodes which announce default gate to internet. How does tinc select which node is prefered when I route to the tinc device and not a special ip? tinc 1.0.16 ALBI...

Hello, did anybody already compile tinc for fritzbox routers? They are very famous in Germany and i like to run tinc on my fritzbox. Otherways maybe anybody can help me how I can do this. But I'm no good programmer... ALBI...

Hi, is there a tinc version for android? I hope so! ALBI...

I use 3 Ubuntu server 14.04 as KVM guest. Now I run 5 tinc vpns in switch mode. I use the same key for every vpn. Every kvm has connect to the two other servers. I need 5 vpns to have 5 networks connected but seperated. 1 vpn was running fine, but now that I run 5 vpns, my kvm crashes sometimes. Especially when I stop tinc. I used tinc 1.0.26 from repo. Now I tried tinc 1.1 pre, same problem but

> homeClient<br> > Network Bridge: (local Area Network and TAP-Win32) 192.168.6.107 mask 255.255.255.0 gw 192.168.6.1<br> change -> mask 255.255.0.0 > Tinc.conf<br> > Name = homeClient<br> > ConnectTo = vpnoffice<br> > Mode=switch<br> Change -> Mode=router Why everybody wants switch??? Add -> TCPonly=yes > vpnoffice: Network

Hi, is it possible to use tinc via https proxy? I mean tell tinc to connect via https proxy to my tinc server. I heared openvpn can do this. Can tinc do that the same way? ALBI...

> If you're using a TAP interface (i.e. layer 2, Ethernet) combined with router mode (an unusual setup, at least on > Linux), Thanks, DeviceType = tap does the job. > operating at layer 3, therefore tinc will strip any layer 2 header (including the MAC address) before sending the packet > across the VPN. As a result, changing the MAC address of the virtual interface will have

Dear All, I am trying to enable router mode of tinc on Windows 7 platform. Although I have enabled the router mode and IP routing in Windows 7 PC (Network A Server). The PC B is still unable to connect the Network A and PC A. But the Network A and PC A is able to communicate each other via tinc. Please help and advise me any incorrect of that. Network A server Real - LAN adapter IP:

Dear list, I'm currently trying to simulate a VPN in a very simple configuration at home. My normal home-net 192.168.0.0/24 serves as "the internet". Three test machines are used, two of them connected to "the internet": odin , external IP 192.168.0.100/24 on eth0 thor , external IP 192.168.0.101/24 on eth0 My VPN uses address space 10.0.0.0/8 in the following way: odin

> I'm using something similar to Amazon's VPCs, where a logical group of > instances has a local subnet from the cloud provider. This local subnet > is always 10.0.0.0/24. As there are multiple VPC's, these private local > subnets dont collide. I do not know what Amazon does, and it looks like I do not want to know it :-) Am I correct? web, gateway and backup have NO

Hello, i'm using a debian etch box (2.6.18-5-686) with tinc 1.0.5 for connecting to my office LAN. On the same box there's a vmware virtual machine running (Windows 2k). Now i'd like to connect this virtual machine through the VPN, too. All my attempts did fail... The virtual machine runs with a "host only" network (vmnet1). On the linux side i tried to configure NAT

Hello, I have tried for days on end with no success on this, so I thought I would post it here and see if someone can help me at all. *Here's the scenario:* I have 1 PC with a Static IP/Domain (a dyndns.org account - myserver.homeip.net) connected to a router, which in turn is the gateway to the internet. It also has a static local IP (192.168.1.2). I will call this the "server"

Hi, is it possible to run two tinc hosts to make failover in case of crash of one tinc host? Or should I switch to tinc 1.1? ALBI...

Hello, I am having an issue with getting tinc to route the packets between 2 Windows tinc installations. Here is what I have so far: homeClient: Physical Interface: 192.168.6.50 gateway 192.168.6.102 homeClient: Tap-Win32 192.168.10.23 no gateway homeClient file: Address:192.168.6.50 Subnet=192.168.10.0/24 vpnoffice: Physical Interface 192.168.6.102 gateway 192.168.6.1 vpnoffice: Tap-Win32

Can I set mac addres of tinc interface in router mode? If yes, how? Thanks for any help. ALBI...

Hello, I just tried tinc for win the first time. I use tinc on linux computer for some time already. Now I get the following error: Dec 18 14:57:39 narnia tinc.life[10884]: Connection from 217.187.51.119 port 35059 Dec 18 14:57:39 narnia tinc.life[10884]: Connection with mwflapar1 (217.187.51.119 port 35059) activated Dec 18 14:57:44 narnia tinc.life[10884]: Received UDP packet from unknown

>> The setup looks like this: >> web <- tinc "tiosp" -> gateway <- tinc "tiutl" -> backup Which lan ips do all your computers have? network addess will be fine. ALBI...

I have been delighted by tinc. Building a mesh like I need would have been horrible in OpenVPN. tinc makes it easy. I decided to share a workaround for a problem that's been vexing me. Either I'm being dumb (and can do this better with a hint) or this is something others might need. I've been moving a bunch of services from our university to Amazon (EC2). To do this, I bring

Many thanks for the help to date. I now have a working vpn with three nodes: 10.20.30.1 10.20.40.1 10.20.50.1 Each machine can see each other machine 100's of miles apart from each other. Each machine is behind its own router. The machines are on their own subnets, as well, of course. The individual IP's on the lans of the nodes are: 192.168.0.155 (corresponds to 10.20.30.1)

> If your question is "can I assign the same subnet to multiple tinc > nodes on the same network", the answer is yes (for both 1.0 and 1.1). Yes exactly. > currently it tries to estimate which one is closest by measuring the > time it took to establish metaconnections along the edges to the node, Shure? I remember alphabetic order (host name) in tinc 1.0. Is it the same