similar to: VPN behind masquerading firewall 1.Opre7

Beste tinc-developer, Ik moet van mijn baas een aantal VPN's aanleggen en ben nu thuis bezig om te testen. Ik heb 2 computers in een thuisnetwerkje (totaal 6 computers) geinstalleerd met SuSe 7.3, daar de klanten dit ook hebben. De computers zijn verbonden met een switch. Dit is de inhoud van mijn bestanden: Op computer 1 genaamd suse met ip 192.168.0.99 netmask 255.255.255.0

Hi, I?m fighting with a silly problem: my syslog tells me tinc cannot route a packet. I can use a telnet or the good ol ping, it is the same effect. When I?m pinging from the laptop (172.16.11.2) the network address (172.16.11.0) or any address numerically lower than the laptops address, the packet gets routed, otherwise not. And when I ping the network address, I get the reply twice, as to be

Hi Ivo and Guus, We are writing a book on building VPNs for Linux and a part of it describes tinc. I wanted to make sure that your opinion, as tinc authors and developers, is reflected. First, let me ask a couple of technical questions. 1. If there are two hosts, foo and bar, that are to be connected via tinc, and each host should only have _one_ IP address (i.e. nmask is /32), would the

Hello, I'm having some routing issue with my tinc setup. I'm running a fairly basic VPN configuration between two networks: ------- Site A: ------- --- tinc-up --- #!/bin/sh /sbin/ifconfig tap0 hs ether fe:fd:00:00:00:00 /sbin/ifconfig tap0 10.11.1.2 netmask 255.0.0.0 /sbin/ifconfig tap0 -arp ---- tinc.conf --- Name = orca Hostnames = no InterfaceIP = 63.108.71.7 KeyExpire =

Hi Who concern, I setup TINC VPN follow these. 192.168.1.x / 24 (Client groups) | 192.168.1.1 (eth1) (GW1) 202.44.34.206 (eth0) || Internet || 202.44.45.14 (eth0) (GW2) 192.168.2.1 (eth1)

I have been having some problems setting up tinc on 2 masquerading linux slackware boxes. routerA is a NAT router to the internet, for two networks on two interfaces. This are the two networks: eth1 Link encap:Ethernet HWaddr 00:E0:4C:6C:6D:86 inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX

Hi! Me and two friends are trying to get a VPN working, but we cant get routing between two tunnels. This is how it looks, all servers (192.168.*.1) are running IP Masquerade to enable the other computers behind them to access the internet. Both elayne and glenn are connecting to melc, and the tunnel between melc and glenn are running TCPOnly because that glenn doesnt have a public IP (it's

Hello, I have 2 hosts HostA and HostB HostA - 10.38.9.2, kernel 2.4.16, tincd from Debian package HostB - 10.38.9.223, kernel 2.2.17-21mdk, tincd from tarball package. HostA: ------------------------------ /etc/tinc/test4/tinc.conf Name = HostA ConnectTo = HostB TapDevice = /dev/misc/net/tun PrivateKeyFile = /etc/tinc/test4/rsa_key.priv /etc/tinc/test4/hosts/HostA Subnet = 10.0.0.0/8 Port =

Hi! When I try to use tinc I get this message 'Cannot route packet: unknown type 0' when I try to ping or ssh to the box I'm connected to. Below is my setup: ifconfig tun device: -------------------- midkemia Link encap:Ethernet HWaddr FE:FD:00:00:00:00 inet addr:192.168.6.1 Bcast:192.168.6.255 Mask:255.255.0.0 UP BROADCAST RUNNING NOARP MULTICAST MTU:1500

> - Indirectdata finally REALLY REALLY works now! > - More precise debug messages Hmmm ... I can't prove that using the CVS code I checked out this morning. Everything works like yesterday: I can ping the peer but I canot go beyond: *** SERVER *** Jun 27 09:04:56 lemon tinc.9[10186]: tincd 1.0pre3 (Jun 27 2000 08:53:56) startin g, debug level 4 Jun 27 09:04:56 lemon tinc.9[10186]:

I'm been experiencing a very very odd problem for the past several weeks and am throwing it out in case someone can shed some light on it for me. There is a single box on our tinc mesh which can be pinged from all hosts, but cannot ping any. It is not limited to ping, the box cannot communicate over tinc. tinc is running in router mode for this mesh. ~30 other nodes function normally,

I have succeeded in getting two tinc1.0pre3 hosts to connect, but I can't ping one from the other. I can ping the local tap interfaces. tcpdump shows that icmp echo requests are received by the other host, but no replies are sent. The two hosts are North and South. It is the same pinging North to South and South to North. The hosts are configured as follows: South: Debian 2.2

Hello again :) Thank you all for your reply's. Below are the config files of the 3 hosts. I use  tinc in router mode. I do not have a kernel mode config lines anywhere so tinc must be using the default settings here. I added the ipaddressx to subnets on hostc and this works. Traffic to that ip is now routed via hostc. But since this ipaddressx address changes often I need to resolve it

Voor de duidelijkheid... ---------- Forwarded message ---------- Date: Sun, 11 Jun 2000 16:14:37 -0500 From: gbarnett <gbarnett@satx.rr.com> To: guus@sliepen.warande.net Subject: TINC 1.0pre2: unable to access one private network Guus... I couldn't seem to get this to the mail list... could you post it and/or answer it for me? Thx. I have been having problems configuring TINC

Hi Tinc Mailing Group, I've got Tinc-1.0pre3 set up on two Redhat Linux 6.2 / kernel 2.2.18 servers. It compiles okay, it reads the configuration files okay, it makes a valid connection between the two tincd daemons. However, it does not route data from one subnet to the other subnet. I will describe my setup below, and if anyone can suggest why it is not working, can they please reply to put

El 12 de febrero de 2016 16:51:59 CET, Eric Yau <ericyaukhy at hotmail.com> escribi?: >Hi All, > > > >I am trying to setup the site-to-site VPN with TINC for connect my home >network to company network. Here is the IP allocation and configuration >for >your reference. > > > >Home PC (192.168.1.2) ?-----? Home (OPENWRT Router, 192.168.1.1, >10.0.0.1)

Whens the point and click GUI coming out? All kidding aside, I seem to be confused about some of the network settings. Essentially all I want is a secure tunnel from machine A to B on two different physical networks, but I can't seem to get there. Just to get things figured out I've got two machines on the same physical network, mach A: 192.168.0.1, mach B: 192.168.0.3. bcast is

Hi, Although Im dutch too, Ill write this in english. I got a similar problem then the one on the helpforum. Ill paste my setup first server tincd.conf ---- ListenPort = 8089 MyOwnVPNIP = 192.168.100.1/24 #VpnMask = 255.255.255.0 TapDevice = /dev/tap0 Passphrases=/usr/local/etc/tinc/passphrases server tapdev ---- tap0 Link encap:Ethernet HWaddr FE:FD:C0:A8:6F:01 inet

I'm having a bit of a problem getting tinc up and running between a pair of RedHat (one 6.0, the other 6.1) boxes. It's installed and configured to the point where they can connect, but I'm not seeing any traffic passing between the two systems. System A looks like - tinc.conf: # Sample tinc configuration. # Insert your own ip numbers instead of the placeholders, # and be sure to use

On Sun, 11 Jun 2000, David Summers wrote: > Thanks for the great software package! The question I have is this: Thank you :) > My goal is to set up a triangle topology VPN between three sites and run > OSPF routing on all the sites so that if a link goes down between any two > sites the OSPF routing will reroute the packets that used to go between > the sites A <-> B to A