similar to: Problem with Beta Nut 2.6.4-1 For Windows

Hello, I am trying to understand how to create a custom configuration for the genericups driver. My system simply signals RI on a serial port on low battery. That's it, nothing else. This serial port is also being used for communications so the other lines are going to be changing all the time, unrelated to the UPS state. Is there a "null" upstype I can use, and then add LB=RNG?

I am using nut 2.2.2 and I have a CyberPower CP550SL. According to the drivers list, I should be using genericups with upstype set to 7, but when I try that and when I run upsc I get: driver.name: genericups driver.parameter.LB: 04 driver.parameter.pollinterval: 2 driver.parameter.port: /dev/ups driver.parameter.upstype: 7 driver.version: 2.2.2 driver.version.internal: 1.34 ups.mfr: CyberPower

I am using nut 2.2.2 and I have a CyberPower CP550SL. According to the drivers list, I should be using genericups with upstype set to 7, but when I try that and when I run upsc I get: driver.name: genericups driver.parameter.LB: 04 driver.parameter.pollinterval: 2 driver.parameter.port: /dev/ups driver.parameter.upstype: 7 driver.version: 2.2.2 driver.version.internal: 1.34 ups.mfr: CyberPower

All, I just bought a Belkin F6C1100-UNV and am trying to get it to work with NUT. I have tried many drivers ( "belkin", "belkinunv", "genericups upstype=4", and "genericups upstype=7", "bestups", "fentonups"). None of them seem to work. Does anyone have any experience with this device? If there is some utility that you all use to

On Jun 20, 2013, at 9:48 PM, Reed Hedges wrote: > UPSPORT=/dev/ttyS0 > > # type cablep kill t powerok battok cableok > robot --- RI 0 /RI --- --- > ? > > Is there an equivalent of ?---? in genericups? I think it's pretty much any value other than a valid

I am working with a number of our customers to ensure that NUT works with different UPS's on Freebsd 9.1. The current one I am looking is support for: *Upsonic Commercial UPS CXR 2000 - 2000VA/1200W - Rack/Tower* What seems to be supported in Freebsd is: CXR1000 blazer_ser LAN Saver 600 genericups upstype=0 Power Guardian genericups upstype=7 PrOffice 650 USB blazer_usb DS-800 USB

On Jan 31, 2014, at 3:14 PM, Chris Duffy wrote: > The current one I am looking is support for: > > Upsonic Commercial UPS CXR 2000 - 2000VA/1200W - Rack/Tower > > What seems to be supported in Freebsd is: Small clarification: the hardware compatibility list isn't broken down by operating system (theoretically, the drivers should work on any POSIX system, with additional

Thx for the info Charles. Here is what I am seeing from 'usbconfig list' ugen0.1: <EHCI root HUB Intel> at usbus0, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE ugen1.1: <EHCI root HUB Intel> at usbus1, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE ugen0.2: <product 0x0024 vendor 0x8087> at usbus0, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE ugen1.2: <product 0x0024 vendor

This code, added to drivers/genericups.h, supports the CyberPower SL series UPSes. I've tested with my 725SL - the online/on battery transition, and low battery status, and finally the shutdown signal all work as expected. *** genericups.h.orig Sun Nov 2 16:54:24 2003 --- genericups.h Mon Oct 3 13:49:00 2005 *************** *** 220,225 **** --- 220,234 ---- TIOCM_ST

Hi Having followed this guide: http://blog.shadypixel.com/monitoring-a-ups-with-nut-on-debian-or-ubuntu-linux/and seeing support for Apollo UPSes mentioned on the compatibility list (genericups, type=4) I tried to set up Nut as follows. OS: Ubuntu Server 12.04 Nut: 2.6.3 (I believe - from Ubuntu repos) ups.conf: > [apollo] > driver = genericups > upstype = 4 > port = /dev/ttyUSB0

On Feb 3, 2014, at 9:05 PM, Chris Duffy wrote: > Thx for the info Charles. > > Here is what I am seeing from > 'usbconfig list' [...] > ugen1.3: <USB UPS PPC> at usbus1, cfg=0 md=HOST spd=LOW (1.5Mbps) pwr=ON > > > The last line I guess is key. Unfortunately, it is not very unique: the vendor can pick the string "USB UPS PPC", but the drivers

Hello folks, I have a question regarding a sweex product. Its bundled with UPSmart v 2.12. I installed nut accordingly to the user manual included in the software. A quick check of data/drivers.list revealed to me i should use the: "Sweex" "500/1000" "contact closure - shipped with UPSmart" "genericups upstype=7" driver this driver

Hi everybody, I've got an Unitek iZi UPS 525 with a serial interface. The supplied cable looks fairly simple: RX->RX , TX->TX and GND->GND. Using this cable and Minicom with 2400 8N1 I'm able to issue commands to the UPS using the "Megatec Protocol" http://www.networkupstools.org/protocols/megatec.html so I know the UPS is fairly "intelligent" :-) and the

Hi, Is there any way to debug a failure of NUT to shut a machine down AFTER the even occurs? (Be it a config issue {Though the standard "It hasn't changed since install" applies}, or a UPS failure, or a program failure). Its showing up (after reboot) as : valhalla# upsc robanton at localhost driver.name: genericups driver.parameter.pollinterval: 2 driver.parameter.port:

Hi All. I was wondering of someone on the list could guide me to the correct driver for the following UPS: Fuden Electronics PCSTAR PT1000. http://www.fuden.com.tw/uninterruptible_power_supply_ups_off-Line_pcstar-1.h tm I have found that with the genericups upstype=7 driver I can see the ups.status going from "OL" to "OB" when I unplug the UPS. Any ideas? Thanks for

Hi, is there a way to use my Belkin F6H650 on the USB port? I already installed usbhid-support, but neither the hidups worked (reports "/dev/usb/hiddev0 is not a UPS") nor genericups with upstype=7 and the hiddev set as device ("ioctl TIOCMSET: Invalid argument") worked. I have installed the debian sarge package of nut 2.0.1 (2.0.1-4) Regards, Philipp

I tried to find a search button for the mailing list but could not. So rtfm me with the link please. If not.. I have an old Deltec PowerRite Pro 2 UPS which has a 9 pin serial cable. By trial and error Im pretty sure I found LB = DCD, but can not get the combination for OB / OL. No matter what I do I get the results below. driver.name: genericups driver.parameter.CP: CTS driver.parameter.LB:

Hi, I'm trying to get a sweex ups working with nut on debian sarge. This one: http://www.sweex.com/producten.php?lang=1&%20sectie=&item=59&artikel=95 It's shipped with UPSmart and according to the compatibility list it should work with the genericups upstype=7 driver. But it doesn't. I get: mybox:/etc/nut# /etc/init.d/nut start Starting Network UPS Tools: (upsdrvctl

Hi, I wanted to report some success with monitoring this UPS, a "Geek Squad" brand GS-700U that I purchased earlier this year from Best Buy Canada. Information about this... thing is very scarce so here is what I know: The unit itself is probably made by Cyberpower. It has a 9-pin serial port on the UPS, as well as a serial-USB adapter thing. I cracked open the serial-USB

Does this require a new entry in scripts/hotplug/* and scripts/udev/*? -- Peter Alexander Gordeev wrote: > > Author: agordeev-guest > Date: Sat May 26 12:04:26 2007 > New Revision: 924 > > Log: > data/driver.list: added SVEN Power Smart RM 2000 to the list. > > Modified: > trunk/ChangeLog > trunk/data/driver.list > > Modified: trunk/ChangeLog >