similar to: Tripp Lite SMART2200CRMXL

Device manufacturer and name: Tripp-Lite OmniSmart500 upsc output: matt at backup:/etc$ sudo upsc tripplite battery.charge: 100 battery.test.status: Battery OK battery.voltage: 14.56 battery.voltage.nominal: 12 device.mfr: Tripp Lite device.model: OMNISMART500 device.type: ups driver.name: tripplite_usb driver.parameter.pollinterval: 2 driver.parameter.port: auto driver.version: 2.4.3

I'm trying to set up a single host to monitor the state of several UPS in my data center. I have a mix of several APC and Tripp-Lite in production. The former are great, the latter are not so much. With the APCs (using usbhid-ups), I can set up configs for each based on the value they report from ups.serial. With the Tripp-Lites (using tripplite_usb), there is no value returned for

Hello list- Anyone with Tripplite SMX1500XLRT2U (http://www.tripplite.com/EN/products/model.cfm?txtModelID=2687) successfully integrated with NUT through serial port? I'm trying to connect to SMX1500XLRT2U using serial cable shipped with UPS under FreeBSD 6.3-STABLE and NUT 2.2.2 installed from ports. Unfortunately, it looks like it couldn't be recognized. %dmesg | grep sio sio0:

Tripp Lite SMART1300LCDT # upsc ups battery.charge: 100 battery.charge.low: 10 battery.charge.warning: 30 battery.runtime: 2951 battery.type: PbAC battery.voltage: 0.0 battery.voltage.nominal: 24.0 device.mfr: Tripp Lite device.model: TRIPP LITE UPS device.serial: 2250AVLSM872100251 device.type: ups driver.name: usbhid-ups driver.parameter.pollfreq: 30 driver.parameter.pollinterval: 2

Good afternoon, I'm trying without much success to monitor a Tripp Lite OMNIVS1500XL using NUT. I checked the compatibility list and saw that this UPS is supported by tripplite_usb. The system is running Debian Stable, but I've downloaded NUT 2.0.3 and compiled from source since the packaged 2.0.1 doesn't include tripplite_usb. I compiled --with-user=nut. My first attempt at

Hello, I am trying to get a SMART500RT1U working on CentOS and just receiving the following message when attempting to start the driver: Network UPS Tools - Tripp Lite OMNIVS / SMARTPRO driver 0.20 (2.6.5) Warning: This is an experimental driver. Some features may not function correctly. Detected a UPS: Tripp Lite /TRIPP LITE SMART500RT1U Unknown input voltage range: 0x02 Unknown number of

Can asterisk act as a SIP registrar or location server? I would like to be able for a user agent(client) to register with whatever client they are using as "username@domain-name.com". Rather than the entry/username/password that is setup in the sip.conf file. That way a user could log into any SIP enable client and their calls would follow them around. I have read the sip.conf man pages

Hi, I'm running Fedora Core 6 and need to monitor a Tripp Lite SMART2200RMXL2U. I've loaded the nut-2.0.3-2.1 RPM. The UPS is connected via the provided USB cable, and that much appears to work: # dmesg | grep -i tripp hiddev96: USB HID v1.10 Device [Tripp Lite TRIPP LITE SMART2200RMXL2U ] on usb-0000:00:1f.4-2 # lspci | grep -i usb 00:1f.4 USB Controller: Intel Corporation 82801BA/BAM

On Mar 6, 2015, at 12:51 PM, Eric Cobb <Eric_Cobb at tripplite.com> wrote: > Network UPS Tools - Tripp Lite OMNIVS / SMARTPRO driver 0.20 (2.6.5) > Warning: This is an experimental driver. > Some features may not function correctly. > > Detected a UPS: Tripp Lite /TRIPP LITE SMART500RT1U > Unknown input voltage range: 0x02 > Unknown number of switchable load banks:

I have a new SMART1050SLT Tripp Lite UPS that both tripplite and tripplitesu drivers hate. Both simply time out with a "can't find" message. Does anyone know about the SmartPro series?

Greetings to all, I recently connected a Tripp Lite SMX500RT1U unit to a Synology NAS (basically a Marvell ARM equipped box running a custom 2.6.24 Linux). I tried using the tripplite_usb driver contained in nut 2.4.1 with not much luck. It does read the model ID and VA rating properly, but fails at everything else - mains voltage (this is a 230VAC EU model), battery config, unit status etc.

On March 6, 2015, at 6:17pm, Charles Leppe ,cleppe at gmail.com> wrote: If this is the same protocol 3005 that we saw in mid-2014 (USB ID: 09AE:0001), then support will be part of the upcoming NUT 2.7.3 release. You wouldn't happen to know anyone who would be able to publish the specs of that protocol, would you? ;-) That would help remove the "experimental driver" warning.

Can anyone point me to information for getting the Tripplite SMART3000RM2U to work with NUT? Our newer Tripplite units seem to work with the usbhid-ups driver, but these older ones seem to need something different. So far I have had little success getting tripplite_usb to work. [root at banyan ~]# tripplite_usb -a tripplite Network UPS Tools - Tripp Lite OMNIVS / SMARTPRO driver 0.20 (2.6.1)

Hello. I'm new to nut and don't know if I've missed something in setting it up or if my ups isn't quite supported. I'm using these: - svn version of nut (downloaded on 9/13/06) - a tripp lite SMART2200RMXL2U - debian sarge with 2.6.8 kernel - the tripplite_usb driver (newhidups says my ups is not supported) I figured out how to get the device perms correct.

Original Message >I have 2 SmartUOS1050SLT's that apparently protocol 3004, has there >been >any progress on getting these units supported under nut? I am running >version 2.4.1, and get the following output when starting the driver. >#lsusb >Bus 005 Device 002: ID 09ae:0001 Tripp Lite ># upsdrvctl -DDDD start >Network UPS Tools - UPS driver controller 2.4.1

I have 2 SmartUOS1050SLT's that apparently protocol 3004, has there been any progress on getting these units supported under nut? I am running version 2.4.1, and get the following output when starting the driver. #lsusb Bus 005 Device 002: ID 09ae:0001 Tripp Lite # upsdrvctl -DDDD start Network UPS Tools - UPS driver controller 2.4.1 Starting UPS: tripplite exec: /lib/nut/tripplite_usb -a

I have several Tripplite SU2200RMXL2U and SU3000RM2U units that I would like to monitor using Nut. I have tried to attach to the units using a serial cable with the tripplite and tripplitesu drivers with no success. The drivers simply seem to not recognize the UPS. I then tried using the tripplite_usb driver with the usb cable. It definitely sees the UPS but I am getting errors which told me

Hey, I am wondering if anyone gotten nut to work with a Tripp Light Smart Pro 2U Rack/Towers (SMART2200RMXL2U). If so which driver did you use, or what driver do you think I should try? Also when trying use a nut driver, do you have to be a nut user? Thanks, Ricky -------------- next part -------------- An HTML attachment was scrubbed... URL:

I recently purchased a Tripp Lite OmniSV1500XL and I've had no luck getting nut to work. # lsusb Bus 001 Device 001: ID 0000:0000 Bus 006 Device 002: ID 05e3:0702 Genesys Logic, Inc. USB 2.0 IDE Adapter Bus 006 Device 001: ID 0000:0000 Bus 002 Device 001: ID 0000:0000 Bus 005 Device 001: ID 0000:0000 Bus 007 Device 001: ID 0000:0000 Bus 004 Device 009: ID 09ae:0001 Tripp Lite Bus 004 Device

Hi I have a Tripp lite smartusb550 using fedora 3 (2.6.12-1.1381_FC3smp). Managed to establish communication with the ups using the tripplite_usb driver but get the following errors Any help to make it work will be appreciated cheers Julio -----------------------------------------------------------------------------------------------------------------------------------------------------