similar to: FreeBSD box dropping packets

Hi. I got this on today's RELENG_6 with Broadcom BCM5722 A0, ASIC rev. 0xa200. >From dmesg (bge related): bge0: <Broadcom BCM5722 A0, ASIC rev. 0xa200> mem 0xe8400000-0xe840ffff irq 16 at device 0.0 on pci2 bge0: firmware handshake timed out, found 0x4b657654 bge0: firmware handshake timed out, found 0x4b657654 bge0: EEPROM read timed out bge0: failed to read EEPROM device_attach:

Hi, I'm having lots of difficulties with BCM5719, which is the default network card of HP Proliant DL 360 G8 servers. I can get a few ping replies before I get a couple of these: bge0: watchdog timeout -- resetting bge0: watchdog timeout -- resetting Then everything hangs. Can not log in using ssh.

Hi, this server, a Dell R720 has 4 bge on board, Broadcom NetXtreme Gigabit Ethernet, ASIC rev. 0x5720000 bge0: APE FW version: NCSI v1.1.7.0 bge0: CHIP ID 0x05720000; ASIC REV 0x5720; CHIP REV 0x57200; PCI-E miibus0: <MII bus> on bge0 ... I have connected the ethernet to port labeled 0, but it appears as bge2, how can this be corrected? thanks, danny

I opened a bug report earlier today but it doesn''t seem to have been added to the bugs database. I''m posting here in case one of the Crossbow developers might see it and confirm this behavior. Description Duplicate packets are generated whenever an aggregate is introduced into the network configuration. We''ve ruled out switch ports and physical bge interfaces as

I'm experiencing similar problems with a 3C996-T under 4.8-REL. In particular, connecting a 4.8-REL machine to a 5.1-REL machine leads to some interesting situations: I can do simple pings across the link, but ssh fails, and heavy pings crash the 4.8 machine. Similarly changing the interface configuration with ifconfig tends to crash the 4.8 machine (mtu, link0, up/down, etc). The

How do I create a vnic that represents the factory assigned MAC address of my physical nic? The bge device in my system (x2100) appears to support 4 MAC addresses. The driver reserves the first as the ''primary/default'' address and allows manipulation of the other three via the MAC_CAPAB_MULTIADDRESS interface. I''d like to use vnics on this system, as I have Xen guest

Recent SUP. Installed on Dell PowerEdge 4600. Getting tons of: Sep 30 12:23:16 zige /kernel: bge0: gigabit link up Sep 30 12:23:46 zige last message repeated 98 times Also getting some TCP retransmits. This causes noticable delays in pretty much everything I do now. Not a problem prior to the SUP. I was on 4.8-STABLE before. When pulling/replacing cables, it went into a mode where it would

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 I'm trying to run a QEMU VM on top of a FreeBSD 7.x server ... I've tried the exact same setup on my desktop, using 192.168.1.x and an fxp device, and it all works perfectly, but as soon as I do this on another machine on a public IP, I'm not getting any routing, I can't even ping it from the same machine ... My first thought was

Hi all, Over the last month or so I've installed FreeBSD 9 (-stable) on several Mac Minis via the memstick image; they seem to be pretty good little boxes for things like offsite secondary nameservers, for example, and they're easily replaced in case of problems. However, the newest minis have slightly different hardware, and FreeBSD can't find the built-in NIC. pciconf -lv on the

Hi, between March 16 and now, bge on a Sun X2200 stopped working, turning off msi (via hw..pci.enable_msi=0) got it working again. I tried first replacing bge with an older version but that did not help. please advice :-) Danny

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hello All, I have had a problem detecting the network card on my notebook when ACPI is enabled for a year. The problem still exists in 7.1-RELEASE. with ACPI: ... bge0: <Broadcom NetLink Gigabit Ethernet Controller, ASIC rev. 0xb002> irq 17 at device 0.0 on pci8 bge0: 0x10000 bytes of rid 0x10 res 3 failed (0, 0xffffffff). bge0: couldn't

Hi Users NUT, I want monitor a UPS of brand SMS (Sinus Double 8 KVA) using a raspberry-pi. In compatibility list, is listed to use the blazer_ser driver. I use a USB adapter to RS-232 conected in to the No-Breake. Follow the comands e confs. root at rasp:/home/pi# lsusb *Bus 001 Device 004: ID 067b:2303 Prolific Technology, Inc. PL2303 Serial Port* Bus 001 Device 003: ID 0424:ec00 Standard

Hello! I have Compaq DL360G2 with Broadcom BCM5701 Gigabit Ethernet and FreeBSD 5.1R installed. There are no problems if I use bge as usual network card, but when I try to use 802.1Q vlans, I can't receive (only receive, sending is ok) packets more then 1456 bytes! What is the problem? BGE driver, VLAN driver or my network configuration? Best wishes, Boris

On Nov 22, 2014, at 5:16 AM, Thiago Wiezbicki <thiagowzb at gmail.com> wrote: > Below , it's a second upsc command using our UPS on battery and with device ID, battery time, battery low time that UPS calcs correctly. Let me remember now, We have the same UPS in 6, 8, 10 and 12 kVA version, and it's names are : Expert C Online 6000 , 8000 , 10000 and 12000 ( or Expert G III

This commit adds a function to dump a DRM GPU VA space and a macro for drivers to register the struct drm_info_list 'gpuvas' entry. Most likely, most drivers might maintain one DRM GPU VA space per struct drm_file, but there might also be drivers not having a fixed relation between DRM GPU VA spaces and a DRM core infrastructure, hence we need the indirection via the driver iterating

I'm trying to understand the newbus and acpi interactions on this Dell R620 that result in the Broadcom adapter board being probed "backwards" or just plain out of order in comparison to the connector layout and the linux tg3 driver. We seem to be detecting PCI0:2:0 before PCI0:1:0. This seems odd to me. When I replace the broadcom daughter card with an intel daughter card, this

I have a back end which has both scalar and vector registers that alias each other. I'm having a problem generating the ISel from tablegen that appears only when a vector register class is declared to contain integer vectors. At that moment tablegen doesn't seem to be able to infer integer types in patterns that it was able to before, but I'm not clear on why that's the

Dear ALL! Maybe someone can help me with my problem? I have no adea what is happening with my packets :( I have 5.4-RELEASE-p8 FreeBSD 5.4-RELEASE-p8 box running pf. And i have ipcad daemon running (installed from ports) pf.conf says pass quick on lo0 all and when i'm trying to rsh to ipcad that is listening on anna# netstat -a|grep shell tcp4 0 0 localhost.shell *.*

*Q: Quick question: does "battery.runtime" update when the device is on battery, or is this field always zero?* *A: Yes, the UPS battery time starts counting when the device starts on battery.* Q: "battery.runtime.low" should be the number of seconds remaining before switching to "LB" status. This seems large, even for a 6000 VA UPS. Is this configurable? A: I

I just BFU''ed up to B61 and started to play with IP Instances. I''m having trouble making my zone happy: root at aeon zones$ zoneadm -z testing1 boot zoneadm: zone ''testing1'': WARNING: unable to hold network interface ''skge0''.: Invalid argument root at aeon zones$ dladm show-dev nge0 link: up speed: 100Mb duplex: full