similar to: handling rc.conf / freebsd init scripts

Hallo, I have one ups with snmp and any ups without snmp. Shutdown works while network online. But some batteries are empty, so that the communication break early. Howto force shutdown if nut-snmp Communications lost? My 1. suggestion was option DEADTIME, but seem to be information only. (s. below) Any suggestions? The last way would be a ugly cronjob (like: ping || shutdown). regards Heiko

In the below example normal Internet traffic is routed as shown from node1 to internet1. The node1 defaultrouter points to the firewall and the firewall points to internet1. For node2 is it possible to add it's own link to the Internet passing through the same default router and firewall as node1. The links do not need to failover or provide any redundancy. node1---node1

Sorry for an off-topic question, but anyone knows how to make network configuration (done with ifconfig/route add) sticky in nexenta core/napp-it? After reboot system reverts to 0.0.0.0 and doesn''t listen to /etc/defaultrouter Thanks.

Hello, My computer is not connecting to the local network with the following configuration: dmesg.boot contains the following lines: ----------------------------------------- vr0: <VIA VT3043 Rhine I 10/100BaseTX> port 0xec00-0xec7f mem 0xfeafbc00-0xfeafbc7f irq 11 at device 12.0 on pci2 vr0: Ethernet address: 00:40:05:a5:00:04 miibus0: <MII bus> on vr0 amphy0: <Am79C873 10/100

Hi, in the kernel I have these lines: [...] device miibus # MII bus support device rl device ed options IPFIREWALL #firewall options IPFIREWALL_VERBOSE #enable logging to syslogd(8) options IPFIREWALL_VERBOSE_LIMIT=0 #limit verbosity options IPDIVERT #divert sockets options DUMMYNET

I am rather at a loss as things seem to change by themselves on this Vista machine. Here's the setup: Vista client, FreeBSD 6.2 server with samba 3.0.25; also a FreeBSD 4.11 machine (server) with samba 2.2.12 Vista connected to samba 3 with password and the machines were present on the network. Then the machines would not show up on Vista at all; they could be pinged and they could be

Hello, I have been using FreeBSD-7.0STABLE with BIND-9.4.2 ( i guess, forget to check before upgrade) up to 2008-01-26 (yesterday). But after upgrade FreeBSD-7.0STABLE-->FreeBSD-7.1STABLE everything goes wrong. 1.BIND can't start anymore and giving me following message at /var/log/messages: . . . Jan 27 12:30:20 ns kernel: ad4: 152587MB <WDC WD1600AAJS-75PSA0 05.06H05> at

Hi all: I have strange probelm with rc.conf. I set up ipfw (compiled into kernel) on freebsd-5.4 and it doesn't seem to load ipfw rulesets (it uses default ruleset 65335 locking out everything). I have to do "sh /etc/ipfw.rules" in order to load the rulesets, once I did that, I can access the box from remote locations here is my rc.conf: host# more /etc/rc.conf

Hi, I have a box with freebsd 9.1-Stable uname -a FreeBSD master.bogdanturcanu.ro 9.1-STABLE FreeBSD 9.1-STABLE #3: Fri Mar 8 18:43:56 EET 2013 root at master.bogdanturcanu.ro:/usr/obj/usr/src/sys/MASTER amd64 The server is connected ussing alc0 interface. If i run: Ifconfig alc0 inet6 x:x:x:x prefixlen 64 it's working. But, if I put in my rc.conf: ifconfig_alc0_ipv6="inet6

https://bugs.freedesktop.org/show_bug.cgi?id=66022 Priority: medium Bug ID: 66022 Assignee: nouveau at lists.freedesktop.org Summary: pwm1[_enable] faults after hibernate/restore related to automatic (or otherwise) fan management QA Contact: xorg-team at lists.x.org Severity: normal Classification: Unclassified

I've got two patterns I want to match on making an outgoing call... (one day - to do Least Cost Routing for Cell/Mobile calls) Firstly - I prefer '0' rather than '9' to get an outside line... Either its a call to a mobile No... (072 -or- 082 -or- 083 -or- 084) or its just another number to dial... I added the following... the playback just advises me which 'route' is

I''m running a ubuntu 9.04 64 bit dom0 with kernel 2.6.29.6 and xen 3.4.0. My eth0 is bridged to br0 and to my guest VMs. The dom0 is running a dhcp server on br0 which is able to provide leases to physical machines on eth0, and also to a windows xp domU which is bridged to br0. However my open solaris 2009.6 domU is unable to obtain a dhcp lease. On the opensolaris side I can see this:

On 05/17/2017 07:18 AM, Oscar Salvador wrote: > This v7 fixes removes dummy functions which only had a return and moves the code > into the switch statements. Hey Oscar, I see new warnings with this series: /home/skeggsb/git/nouveau/drm/nouveau/nouveau_hwmon.c:645:8: warning: assignment discards ‘const’ qualifier from pointer target type [-Wdiscarded-qualifiers] *buf = input_label;

Hello Lartc Mailing List: Been working on something the last week and a half and ALMOST have it working.., just need a few pointers from the wizards on this mailing list to nail it. Ok, my setup is a hub and spoke arrangement, hub is Cisco 2821 with IOS 12.4. Spokes are ruggencom RX1000 routers, Debian based with the following versions installed: rx1000test:~# uname -a Linux rx1000test

>sample setups of freeswan working with shorewall? I just implemented this a few days ago. In my case it was the simple scenario of two private subnets (with different private network numbers!) already equipped with Shorewall firewalls on which I added Freeswan. The hardest part was being patient enough for the other end''s firewall (a 486= ) to compile the patched kernel. I basically

Hi all, I am trying to use usb passthrough for an usb wireless adapter to a kvm guest under a CentOS7 host. Guest can connect to an AP and sometimes receives an IP and sometimes not. But when and IP address is assigned by an AP (and defaultroute), nothing works. If I try to resolv any host like for example www.google.com, there is no result ... Trying to ping 8.8.8.8 doesn't works also.

Hello all, I am working on a VPN solution using FC3-2.6.12-1.1381 - openswan 2.4.4-1 - l2tpd 0.69-13 - pppd 2.4.3-5 - samba 3.0.10-1. When attempting a connection from an XP-SP2 box pppd dies without authenticating the user (see below). I have run ntlm_auth from the command line with success. What tools can I use to identify the failure? Is there an obvious error in the ppp options file?

I''m following the example provided in the type reference under ''zone'', i.e.: zone{myzone: autoboot=>true, create_args=>"-b", ip=>"nge0:10:130.55.201", path=>"/zoneds/%s", realhostname=>"myzone.example.com",

My goal is to make VPN access to our Samba PDC (FreeBSD 7.0) so that users can access there home shares from Windows clients. I have read the instructions at http://samba.org/ftp/unpacked/lorikeet/pppd/final-report.pdf, but I can't make it work. Don't know if is due to my lack of skills or has something to do with the Popop functionality in FreeBSD. Following the instructions, i made a

Hi @ll it works (now a small description, please note this was only test setup to bring me nearer to the desired function !!!) i just compiled the new pppd 2.4.3 in my suse 9.2 system. ( i build a suse rpm ) i ve configured a test smb pdc ------------------------------------------------ [global] encrypt passwords = yes unix charset = ISO8859-1 display charset = ISO8859-1