similar to: BGE & VLAN stranges

I'm experiencing similar problems with a 3C996-T under 4.8-REL. In particular, connecting a 4.8-REL machine to a 5.1-REL machine leads to some interesting situations: I can do simple pings across the link, but ssh fails, and heavy pings crash the 4.8 machine. Similarly changing the interface configuration with ifconfig tends to crash the 4.8 machine (mtu, link0, up/down, etc). The

Recent SUP. Installed on Dell PowerEdge 4600. Getting tons of: Sep 30 12:23:16 zige /kernel: bge0: gigabit link up Sep 30 12:23:46 zige last message repeated 98 times Also getting some TCP retransmits. This causes noticable delays in pretty much everything I do now. Not a problem prior to the SUP. I was on 4.8-STABLE before. When pulling/replacing cables, it went into a mode where it would

Hi, between March 16 and now, bge on a Sun X2200 stopped working, turning off msi (via hw..pci.enable_msi=0) got it working again. I tried first replacing bge with an older version but that did not help. please advice :-) Danny

I opened a bug report earlier today but it doesn''t seem to have been added to the bugs database. I''m posting here in case one of the Crossbow developers might see it and confirm this behavior. Description Duplicate packets are generated whenever an aggregate is introduced into the network configuration. We''ve ruled out switch ports and physical bge interfaces as

Hi, I'm having lots of difficulties with BCM5719, which is the default network card of HP Proliant DL 360 G8 servers. I can get a few ping replies before I get a couple of these: bge0: watchdog timeout -- resetting bge0: watchdog timeout -- resetting Then everything hangs. Can not log in using ssh.

Hi, this server, a Dell R720 has 4 bge on board, Broadcom NetXtreme Gigabit Ethernet, ASIC rev. 0x5720000 bge0: APE FW version: NCSI v1.1.7.0 bge0: CHIP ID 0x05720000; ASIC REV 0x5720; CHIP REV 0x57200; PCI-E miibus0: <MII bus> on bge0 ... I have connected the ethernet to port labeled 0, but it appears as bge2, how can this be corrected? thanks, danny

I need a timing device for the DL360G2 for conferencing and meetme. For a timing device I have 2 X100P cards but neither will work in my DL360G2. The system will not even boot with either card in the system. Other PCI cards seems to work fine. I called Digium support and was told that there must be a conflict between the card and my Compaq DL360G2. I then moved on to ztdummy. I'm sure the

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 I'm trying to run a QEMU VM on top of a FreeBSD 7.x server ... I've tried the exact same setup on my desktop, using 192.168.1.x and an fxp device, and it all works perfectly, but as soon as I do this on another machine on a public IP, I'm not getting any routing, I can't even ping it from the same machine ... My first thought was

Does anyone know where to disable rtc support on redhat 9.0 using make menuconfig? I thought I disabled it but still got the following error when trying to make zaprtc: zaprtc.c:109: storage size of `rtc_irq_timer' isn't known zaprtc.c:719: storage size of `rtc_fops' isn't known zaprtc.c:107: warning: `DECLARE_WAIT_QUEUE_HEAD' declared `static' but never defined make: ***

Sorry for the cross-post, but this could be either lists problem. I have 2 boxes running 7-STABLE as of 20081130, both i386 SMP. One is running ISC DHCPD 3.0.x from recent ports, and the other dhclient from make world. The server is refusing to answer the DISCOVER request, as it thinks the IP checksum is wrong, which tcpdump also confirms. Other DHCP clients are working fine on this network,

Author: mabloom Repository: /hg/zfs-crypto/gate Revision: 39c5623029b347adbf2ab92400d25328f7b321ee Log message: 5084264 Error messages output when configure jumbo frames using bge.conf Files: update: usr/src/uts/common/io/pci_pci/pci_pci.c

Hi. I got this on today's RELENG_6 with Broadcom BCM5722 A0, ASIC rev. 0xa200. >From dmesg (bge related): bge0: <Broadcom BCM5722 A0, ASIC rev. 0xa200> mem 0xe8400000-0xe840ffff irq 16 at device 0.0 on pci2 bge0: firmware handshake timed out, found 0x4b657654 bge0: firmware handshake timed out, found 0x4b657654 bge0: EEPROM read timed out bge0: failed to read EEPROM device_attach:

Hello R users and developers, I had a problem when I tried to install the last version of R-devel. I know that this R version is an unstable version and that this problem may be irrelevant. I am maintaining a R package thus I check if this package can be installed with the development version. ( Everinthing is fine with the R-patched) The details are the following: My machine: System:

Hi all! We use pxelinux for booting a diskless Linux from whitch we install all our systems. But we discovered some Problems: - With v1.75 the Kernel is fetched from the TFTP-Server with no problem, but it gets not started on Broadcom NetXtreme with newer PXE-Bioses - With v2.04, pxelinux even seems not to be able to fetch the kernel from the TFTP-Server. This affects also Intel's

I have a back end which has both scalar and vector registers that alias each other. I'm having a problem generating the ISel from tablegen that appears only when a vector register class is declared to contain integer vectors. At that moment tablegen doesn't seem to be able to infer integer types in patterns that it was able to before, but I'm not clear on why that's the

I have a Dell 1435 system that will not respond correctly to a com32 call to Local boot Int 22h AX=14h DX = 0 This call should not return. It should unload the PXE+UNDI stacks and continue the boot process with the next boot device. This call is working fine for me on an HP DL360G2 and on a Dell PE 850. But, on this Dell 1435 the call is returning from the Int 22h. I am using syslinux 3.51

Dear All, I have a FreeBSD box running 5.4-RELEASE-p8. Two interfaces: fxp0 - internet, SKA4 internal interface fxp0: <Intel 82559 Pro/100 Ethernet> bge0 - internal with 30 vlans on it, old bge Gigabit 64/32 PCI-2.1 adapter. bge0: <Altima AC1002 Gigabit Ethernet, ASIC rev. 0x105> Firewall is pf with about 5000 rules. A week ago it was working just properly, but after adding more RAM

How do I create a vnic that represents the factory assigned MAC address of my physical nic? The bge device in my system (x2100) appears to support 4 MAC addresses. The driver reserves the first as the ''primary/default'' address and allows manipulation of the other three via the MAC_CAPAB_MULTIADDRESS interface. I''d like to use vnics on this system, as I have Xen guest

On Sun, 22 Apr 2007, Christopher Lamb wrote: > I have a back end which has both scalar and vector registers that > alias each other. I'm having a problem generating the ISel from > tablegen that appears only when a vector register class is declared > to contain integer vectors. At that moment tablegen doesn't seem to > be able to infer integer types in patterns that it was

Hi all, Over the last month or so I've installed FreeBSD 9 (-stable) on several Mac Minis via the memstick image; they seem to be pretty good little boxes for things like offsite secondary nameservers, for example, and they're easily replaced in case of problems. However, the newest minis have slightly different hardware, and FreeBSD can't find the built-in NIC. pciconf -lv on the