similar to: Load Balance between 2 NIC

First of all i wanna thanks Christoph Simon for the support. Only after his reply to my email i could see the real solution to the problem (Valeu mesmo cara... me ajudou pra caramba! Fico te devendo essa!) :) Here is what i learned in a month of research: I tried A LOT of things to do load balance, including the one at LARTC homepage. The only tutorial that REALLY works in my case is the

Hi list, I have to configure a internet server with linux. I need configure traffic balance between dsl and cable connection. Somobody sugestion some solution? Thanks Rafael de Souza _______________________________________________ LARTC mailing list / LARTC@mailman.ds9a.nl http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

Hello all, I am going through the LARTC howto to understand how the iproute2 works. But some concepts like Policy Routing, RPDB etc are not clear to me. I am pretty new to iproute, beeing using route command for long... From what I understand 1. rules (ip rule) tell how to select packets for routing and route (ip route) tell where to route the selected packets. 2. A collection of rules is

Hello all, I do not read C very well (especially kernel C). Though I have tried to muddle my way through an understanding of what''s going on in fib_hash.c, fib_rules.c, and route.c, I have not succeeded to my satisfaction, hence my post. I''m trying to document the general process of route selection, and have come up with the following overview. Could somebody point out any

I have two adsl lines on my linux firewall box and i want to do some load balance between them...i tried a lot of different things, but it isn´t working...Following the instructions of http://lartc.org/howto/lartc.rpdb.multiple-links.html i used the configuration above. using "iptraf" I can see some few packets using the ppp1 connection, but almost all the packets use ppp0 connection.

Hello All, I have a linux box running with three NIC''s, I have used brctl tool to configure this box as a bridge, i have given it ONE logical ipaddres, Every thing is working fine, but now i am required to configure the same bridge as a LOAD BALANCER.... On some googling i found the following link http://lartc.org/howto/lartc.rpdb.multiple-links.html This HOWTO requires me to have one

HI All , I am running a FC6 box with two internet links with load balance . Every thing is working fine expect the MSN connection that failed and reconnect every time and SSL connections . I would link to know if with the nona howto I could fix that . I have been tried with no success to redirect that connection only to one link but its look like do not work . Here my configuration :

Hi, I''m sorry for "novice"-level question, but I hope your expert advice will save me many painful hours running after my own tail... Let assume I have Linux box with eth0, eth1 and eth2 interfaces. Each one has IP assigned from different network. By default, IP address associated with eth0 is chosen as default routing. My application creates thee TCP sockets and explicitly

Hello, I started off by reading the Linux Advanced Routing & Traffic Control Howto, then searched a bit around the web. I see many documents discussing these matters with kernel 2.2.x but they are quite old, something around 1998-2000. I have some questions but I might as well start by exposing my setup to clarify things. I have a couple of internet links: a leased line of 256kbit/s and an

Hi guys, Can you take a look at this? :) +-----------+ | | eth1-|- | | -|-eth0---LAN--- | | eth2-|- | | | +-----------+ - eth0 is connected to the LAN having the IP=LAN_IP eth1 is connected to the first ISP having IP=ISP_IP_1 and GW=ISP_GW_1 eth2 is connected to the second ISP having IP=ISP_IP_2 and GW=ISP_GW_2 I need

Hi, I''ve set up a Linux box with redhat on to act as an internet gateway and I''m running into a few problems. Its got two adsl modems connected to it, both connected to seperate 512kbs lines. Now I''ve followed the simple source routing in the advanced routing howto to the letter but it doesnt work. I''ve got it autoconnecting on startup and redhat puts ppp1

ok i will do it in text: 66.92.114.46 eth0 209.141.2.194 eth1 192.168.119.101 eth2 192.168.120.101 eth3 What i have is a linux box RH7.3 which will eventually run Shorewall Firewall. On this box there is eth0 66.92.114.46 conneted to isp1 and eth1 209.141.2.194 connected to isp2 It also has eth2 192.168.119.101 and eth3 192.168.120.101 which will connect to a failover appliance which has 2 wan

Hello, I''m new to the list and iproute2 itself. I was searching for a way to simultaneously use several IPs on the *same network interface* for outbound traffic. Let me explain: I have eth0 interface to which I set 2 IP addresses; 192.168.0.1 and 192.168.0.2. Then I want to connect to Internet through 192.168.0.254 gateway using round-robin between those 2 addresses. The iproute2

I have two ISP links that I am trying to firewall through a Linux Server, I have been following http://lartc.org/howto/lartc.rpdb.multiple-links.html and I can not seem to get it working. Do you have to NAT the incoming packets for this to work correctly?

Hi! In our students'' hostel we have 6 DSL lines (dialups to different providers); we have set up a linux box (currently running 2.6.11-rc2-mm2, but the problem described hereafter also applies to previous 2.6-series kernels) with help from http://lartc.org/howto/lartc.rpdb.multiple-links.html#AEN298 Our Setup looks like this: 10.0.0.0/8 10.70.255.1 +----------+ +-----------+ |

hi, i wann to make multigateway routing and i read ur how to on http://lartc.org/howto/lartc.rpdb.multiple-links.html and create some rules which i am sending u, but with this rules i am not able to do multigateway routing on my linux router so plz help me out. thanks the rules are given below IF0=eth0 IF1=eth1 IF2=eth2 IP1=192.168.1.2 IP2=61.246.243.86 P1=192.168.1.1 P2=61.246.243.81

I have two T1s and I'd like to split my SIP traffic over the two. I am looking at this: http://lartc.org/howto/lartc.rpdb.multiple-links.html what bothers me about it is the note "Note that balancing will not be perfect, as it is route based, and routes are cached. This means that routes to often-used sites will always be over the same provider.". If all my traffic goes to the same

On 3/8/2016 8:47 PM, Clint Dilks wrote: > Here is documentation that may help > http://lartc.org/howto/lartc.rpdb.multiple-links.html but as John mentions > it is painful to get right. sadly, that document is like 15 years old, and hasn't been updated. the basics are still valid, but things like how to integrate that with RHEL startup scripts? nada, you're on your own.

I configured multiple isp (actually only multiple gw) according http://lartc.org/howto/lartc.rpdb.multiple-links.html. Now NAT (Internet) seems to work, both external interfaces work ( I didnt configure load balancing because I dont need it). However I have problem that I can not ping from NAT to public ip of my Linux box. Problem is that I can not connect from 192.168.1.0/24 network to services

Hi, this might be a dumb question, but I''m not finding much information online. I''m trying to setup a 2.6 linux box to run nat across multiple upstream links as a simple way to aggregate bandwidth. I found the instructions in lartc section 4.2 (http://lartc.org/howto/lartc.rpdb.multiple-links.html) fairly clear and straightforward. I implemented those, and a couple of trivial