similar to: Bonding problem in CENTOS4

Getting "bnx2i: iSCSI not supported, dev=eth0" for all the NIC adapters on all of my R710's running CentOS 5.5. Here is an sample of the error messages: bonding: Warning: either miimon or arp_interval and arp_ip_target module parameters must be specified, otherwise bonding will not detect link failures! see bonding.txt for details. bonding: bond0: setting mode to active-backup

I have a machine I just deployed w/ tg3 interfaces, I have setup bonding on this same line of server (HP DL380 G4) a million times. I saw there were changes recently to how you configure a bond and have my setup configured according to: http://kbase.redhat.com/faq/docs/DOC-7431 The HP switch has a LACP trunk defined on the two ports. Problem is, when rebooting, I need to issue a `service network

I come across some problem when using xen-4.1.1-rc1-pre from xen-4.1-testing tree and 2.6.32.36xen linux kernel from git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen.git. when I use ''xend restart'' , it hangs when kernel dmesg printing ''Bridge firewalling registered'' and the console show below messages: localhost# xend restart Nothing to flush. Cannot

Am 02.07.2015 um 20:16 schrieb Gordon Messmer: > Have you yet: > setsebool -P use_samba_home_dirs 1 > _______________________________________________ > CentOS mailing list > CentOS at centos.org > http://lists.centos.org/mailman/listinfo/centos > > No, I didn't set it. Now I've set it and when logging into text console I no longer have the problem with the home

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi list, I have a *very* strange problem, unfortunately it's kind of a show stopper regarding the deployment of the machine. :( I have two Intel Gigabit Ethernet NICs on board (Supermicro-based Server), quoting lspci (full output see at the end of the email): 0d:00.0 Ethernet controller: Intel Corporation 82573E Gigabit Ethernet Controller

Hi all, it''s happening a strange thing: After I boot the xen dom0 network is unavailable: I have to unload the network modules and load it again ( rmmod / modprobe) and execute a service network restart) This is strange, what do you suggest me to check? Thanks Marco Strullato _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com

This issue was brought up about a year and a half ago. So I''ll bring it up again and see if anything happens. I''ve got an infiniband network and am attempting to pass the infiniband card through the host and give it to the guest. I''m working with standard CentOS 5.2 on both guest and host with their provided xen (3.0.3 ish). I''ve also attempted to install the

This issue was brought up about a year and a half ago. So I''ll bring it up again and see if anything happens. I''ve got an infiniband network and am attempting to pass the infiniband card through the host and give it to the guest. I''m working with standard CentOS 5.2 on both guest and host with their provided xen (3.0.3 ish). I''ve also attempted to install the

I am trying to transport a dd image between to hosts over a cross linked gigabit connection. Both hosts have an eth1 configured to a non routable ip addr on a shared network. No other devices exist on this link. When transferring via sftp I received a stall warning. Checking the logs I see this: dmesg | grep eth e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:1c:c0:f2:1f:bb

I inherited a xen server that is setup to have all the VM images hosted on an iSCSI mounted NAS array. We been experiencing a random (about every 2-3 days) issue where xen would crash all the VMs, leaving nothing but the Domain0 running. What appears to be happening is something causes the iSCI mount to hiccup. Running "vgchange -a y" and restarting all the VMs brings everything up.

I am using centos 5 x86_64 AMD64 X2 4200+. I am current on yum update. My machine has two ethernet cards. e1000 (eth0) and forcedeth (eth1) [root at fsdsigns2 ~]# more /etc/modprobe.conf alias eth0 e1000 alias eth1 forcedeth sometimes on boot the forcedeth driver thinks it is eth0: [root at fsdsigns2 ~]# dmesg | grep eth forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.60.

The Geforce 9800GT also shows different behaviour without nvidiafb in the kernel. I get lengthy messages from nouveau, like the ones found in the email attachment. It also eventually gets into the lightdm login graphical screen, but with this card the screen is highly distorted, despite the mouse cursor being properly displayed and moving around properly. Luis On Thu, Jan 25, 2018 at 1:14 PM,

Hi, kickstarting fails due to problems with host resolution, even though the network seems to be properly configured through DHCP. eno1 and eno2 are both attached to the network, but only eno1 gets an IP via DHCP. Still `curl` cannot resolve the mirror host and the kickstart host during dracut-initqueue: rdsosreport.txt ------------------------------------------------ [...] [ 14.780428]

Hi, I've using linux bonding in active-backup mode to combine two pairs of GigE NICs (eth0/eth1, eth2/eth3) into two logical bonds (bond0/bond1). All is working fine. However, I would like to specify a primary interface for each bond. This means I need to specify different options to the bonding module for each bond. I have tried every conceivable incantation of options and cannot get the

Setting up bonding in active-backup mode 1 (using ARP monitoring) on a server, it looked OK, but pulling the active link cable didn't actually work, it didn't fail over. Eventually with manual playing around with modprobe, ifconfig, ifenslave, etc., a solution was stumbled upon: enslave the eth1 device before eth0, and all is good. Why this should matter is a puzzle - I could not find

(first post) Dear all, I have been wrestling with this issue for the past few days ; googling around doesn't seem to yield anything useful, hence this cry for help. Setup : - I am running several RHEL5.4 KVM virtio guest instances on a Dell PE R805 RHEL5.4 host. Host and guests are fully updated ; I am using iperf to test available bandwidth from 3 different locations (clients) in the

HI All. I have a linux box connected to a switch network with 2 network interfaces, how would I able to ''trunk'' these 2 interfaces? options I can see are: - ethernet bonding - iproute2? - teql Which one are the best to use? I''m curretly having problem with ethernet bonding, my setup are as follow: ip add: 192.168.10.30/24 I do: # modprobe bonding # ip addr add

Dear All, Please ignore my previous mail I have using CentOS 4.4 Linux and Kernel Version is 2.6.9-42.EL I have configured Cluster Suite with 2 servers Server 1 : 192.168.13.110 IP Address and hostname is primary Server 2 : 192.168.13.179 IP Address and hostname is secondary Floating : 192.168.13.83 IP Address (Assumed by currently active server) I have configured Ethernet Channel Bonding in

Hi, I'm trying to configure a network bridge over a bonding without any success. Here is my configuration: ifcfg-eth0: DEVICE=eth0 HWADDR=00:1E:C9:E8:3F:E5 ONBOOT=yes USERCTL=no MASTER=bond0 SLAVE=yes ifcfg-eth1: DEVICE=eth1 HWADDR=00:1E:C9:E8:3F:E7 ONBOOT=yes USERCTL=no MASTER=bond0 SLAVE=yes ifcfg-bond0: DEVICE=bond0 ONBOOT=yes BRIDGE=br0 USERCTL=no ifcfg-bridge0: DEVICE=br0

I four nodes setup to do active-backup bonding and the drivers loaded for the bonded network interfaces vary between tg3 and e100. All interfaces with the e100 driver loaded report errors much like what you see here: bonding: bond0: link status definitely down for interface eth2, disabling it e100: eth2: e100_watchdog: link up, 100Mbps, full-duplex bonding: bond0: link status definitely up for