similar to: Samba 3: bad read performance

Assuming I have a firewire card with a supported chipset, is there anything special I need to do in order for the kernel to recognize the card? Shouldn't kudzu "wake up" and configure the card when I boot up after installing it? This is a brand spanking new 4.4 system and a supported Agere chipset firewire card. I'm having trouble tickling devices connected to the card.

Hi all, I am using Xen 2.0.7. I have Broadcom NetXtreme BCM5704 Gigabit Ethernet (rev 02) cards which support frames greater than 1500. However when I boot into Xen and try to set the MTU to anything higher than 1500 (e.g., 4000, 8000 etc) I get a segmentation fault. After this fault, every command fails with a segmentation fault. I saw a similar bug report posted here:

I totally agree with Luc Boudreau about this problem. On modern branded server they ALL use Broadcom chipset... I must admit that: a) lot of people are experiencing the problem but can tolerate it or b) someone already experienced this problem and solved it Lets'' approach the problem pragmatically... just start with a survey on the list. ... hope we solve this issue soon. Ivan

Hi all! We use pxelinux for booting a diskless Linux from whitch we install all our systems. But we discovered some Problems: - With v1.75 the Kernel is fetched from the TFTP-Server with no problem, but it gets not started on Broadcom NetXtreme with newer PXE-Bioses - With v2.04, pxelinux even seems not to be able to fetch the kernel from the TFTP-Server. This affects also Intel's

hi i''m using htb + u32 filters, and i was wondering if there is something one can optimize at this stage. i have a lot of filters (~ 50.000 / interface, and there are two interfaces), and around 4500 classes / interface. the traffic going through this machine is something around 210-230mbit/s at 50kpps. as you can imagine, the load is pretty high. in fact (as it''s a dual xeon at

Hi Group, I have a problem with my FXO interface. It seems that asterisk cannot see any configured channels, only pseudo. Pls see the error and my config below. Rgrds Markus ----- May 2 15:09:00 NOTICE[17327]: app_dial.c:1010 dial_exec_full: Unable to create channel of type 'Zap' (cause 0 - Unknown) == Everyone is busy/congested at this time (1:0/0/1) == Auto fallthrough, channel

Hi everyone, I'm trying to use samba in a small video post production house but we are not getting the performance we expected. Our setup: - CenOS 5.6 x86-64 - samba.x86_64 (3.0.33-3.29.el5_6.2 and 3.6.0rc1) - Intel based server (One 4 core Xeon E5620 @ 2.40GHz, 8 GB RAM) - 4 Intel Gigagit ethernet NIC ports with 802.3ad bonding connected to a switch configured tu use 802.3ad - 8 2TB 7.2

I have a machine I just deployed w/ tg3 interfaces, I have setup bonding on this same line of server (HP DL380 G4) a million times. I saw there were changes recently to how you configure a bond and have my setup configured according to: http://kbase.redhat.com/faq/docs/DOC-7431 The HP switch has a LACP trunk defined on the two ports. Problem is, when rebooting, I need to issue a `service network

On RedHat Enterprise Linux 6, the test below fails (this is using the stock GCC 4.4.7) from R-devel r72707. LC_CTYPE is unset when I run it, but LANG=en_US.UTF-8 It also failed "yesterday" where as far as I recall the test code looked a bit different. Best, Kasper > ## Results differed by platform, but some gave incorrect results on string 10. > > > ## str() on large

Hello list, I have two differents installation Xen Hypervisor on two identical physical server, on the same switch : The problem is on my new server (Xen 4.0.1 with pvops kernel 2.6.32.24), I have bad performance on bandwidth I have test with a files copy and "iperf". Result iperf average: Transfert Bandwidth XEN-A -> Windows

>>>>> Kasper Daniel Hansen <kasperdanielhansen at gmail.com> >>>>> on Fri, 19 May 2017 20:09:24 -0400 writes: > I rebuilt R with > export LC_CTYPE=en_US.UTF-8 > and the test still fail. Surprisingly, when I run R from the bin directory > and execute the test code, it runs without error: >> oloc <-

Hi all, I am trying to get some decent speed out of a vanilla Debian (Proxmox) box and am running out of ideas. Basically I can exchange data at 110MB/sec (raw, nfs, ftp) but not with Samba shares. I tried almost every samba tuning tip I could find to no avail. The only optimisation left to smb.conf at the moment is debug level = 0. As one can see the robocopy throughput is merely half of what

This sounds kind of like what happened with me for earlier attempts at using syslinux. Skip using HPA's tools entirely and dd if=vmlinuz of=/dev/fd0 bs=1440k count=1 and make sure that the kernel runs from a floppy disk. There'll be no file system or anything, but you'll make sure that your kernel isn't faulty. If it doesn't execute, then you can avoid the syslinux/pxelinux

hi there. anyone have any tips on params to pass to the kernel etc in order to install Centos4 or Centos5 32bit or 64 bit installed on this unit i can get it close to install, yet no cigar. it is a tyan MB and ill try to get more info if needed... for this case, please assume for now that the hardware itself is not "bad" thanks in advance... - rh Rackable Systems Dual Opteron 2.0

Hey all I''m new to Linux and Virtualizing. I''m trying to dedicate my nic''s to each virtual server. For instance, virt server A would use nic1 and virt server B would use nic2 and so on. I''ve been reading some stuff for this list and to tell you the truth I''m a bit overwhelmed. We are going to run SLES10.1 and Xen. I would appreciate any assistance.

This might be a crazy idea, but it just popped into my head, and I wanted to know if it''s possible. Perhaps not possible right now, but possible in a theoretical sense. Is it possible that puppet could be modified to be used to manage switches that have a command line based interface? When I manage our Allied Telesis switches (which have a CLI similar to cisco IOS) I wonder if I could

Hello, I've got a very strange problem. Lately I've been setting up my linux servers for network (layer2) redundancy with a bridge interface containing two ethernet interfaces connecting to two switches. So far I didn't have any problems with it, but now a very strange thing happens with a new server I'm installing. The server is an ibm x346 having two onboard BCM5721 cards, the

http://pastebin.com/raw.php?i=MwDnhknf $ ls -Sl total 461252 -rw-rw-r--. 1 g g 111709730 Jan 22 11:06 linux-2.6.37.zip -rw-rw-r--. 1 g g 93174605 Jan 22 11:03 linux-2.6.37.tar.gz -rw-rw-r--. 1 g g 73552510 Jan 22 11:10 linux-2.6.37.tar.bz2 -rw-rw-r--. 1 g g 66333786 Jan 22 11:16 linux-2.6.37.7z -rw-rw-r--. 1 g g 64035788 Jan 22 11:16 linux-2.6.37.tar.7z -rw-rw-r--. 1 g g 63480808 Jan 22

Hello, Does anyone have bonding working under CentOS on a modern Proliant? What driver do you use? My setup: Centos x86_64 4.3 fully patched on a Proliant DL380 G4. 2 built-in NICs: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet (rev 10) Using the tg3 driver that came with the OS. I'm trying to set up bonding between the 2 built-in Broadcom NICs in active-backup mode with each NIC

Reading a flat text file 138 Mbyte large into R with a combination of scan (to get the header) and read.table. After conversion of text time stamps to POSIXct and conversion of integer codes to factors I convert everything into one data frame and release the old structures containing the data by using rm(). Strangely, the rm() does not appear to reduce the used memory. I checked using