similar to: Copy from Samba to XP Very Slow

greetings list. am serving SMB using the samba-3.0.24 package on an openbsd 4.1-release machine and am seeing really low throughput from the server, even when both the server and client are on gigabit ethernet. the maximum throughput i've been able to attain is ~6 MBps, which is pretty slow, both on 100 Mbps and 1 Gbps segments. this top speed is identical on both 100 Mbps and 1 Gbps.

I have some questions about what needs tuned on a high traffic syslog box. I seem to be dropping quite a few syslog packets. This is a syslog server for a high usage Firewall btw. Nic is a Compaq tl0 4.8-P13 netstat -s -p udp | grep buf 19,762,079 dropped due to full socket buffers uptime 5:28PM up 7 days, 18:30, 2 users, load averages: 0.21, 0.23, 0.23 I though maybe syslogd was the

If someone has some free time, can you go over my ipfw config. See if I have any problems, or things i should add. Im not an ipfw expert or anything. Here is the config. add 100 allow all from any to any via lo0 add 110 deny log all from any to 127.0.0.0/8 add 120 deny log ip from 127.0.0.0/8 to any add 00200 check-state add 00250 deny all from any to any frag in via bge0 add 00260 deny

Hi, Was wondering if there are any plans to update either the kernel structures and/or netstat to show more than 4GB of traffic stats. For example, on a 4.8-STABLE machine: $ netstat -bI sis0 Name Mtu Network Address Ipkts Ierrs Ibytes ... sis0 1500 <Link#2> <mac-addr-hidden> 8789598 0 4103727771 ... <non-relevant parts removed> This shows that

Hi, I'm having lots of difficulties with BCM5719, which is the default network card of HP Proliant DL 360 G8 servers. I can get a few ping replies before I get a couple of these: bge0: watchdog timeout -- resetting bge0: watchdog timeout -- resetting Then everything hangs. Can not log in using ssh.

I'm experiencing similar problems with a 3C996-T under 4.8-REL. In particular, connecting a 4.8-REL machine to a 5.1-REL machine leads to some interesting situations: I can do simple pings across the link, but ssh fails, and heavy pings crash the 4.8 machine. Similarly changing the interface configuration with ifconfig tends to crash the 4.8 machine (mtu, link0, up/down, etc). The

Hi. I got this on today's RELENG_6 with Broadcom BCM5722 A0, ASIC rev. 0xa200. >From dmesg (bge related): bge0: <Broadcom BCM5722 A0, ASIC rev. 0xa200> mem 0xe8400000-0xe840ffff irq 16 at device 0.0 on pci2 bge0: firmware handshake timed out, found 0x4b657654 bge0: firmware handshake timed out, found 0x4b657654 bge0: EEPROM read timed out bge0: failed to read EEPROM device_attach:

Hi all, I installed 2009.06, xVM and happily installed a domU with no issues. I just did this through the virt-manager GUI, and kept it as simple as possible. Later I installed and booted a zone with very simple and standard configuration. My existing xVM virtual machine did not immediately stop working, or have any interruption at all. But, I can no longer create new virtual machines, or even

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hello All, I have had a problem detecting the network card on my notebook when ACPI is enabled for a year. The problem still exists in 7.1-RELEASE. with ACPI: ... bge0: <Broadcom NetLink Gigabit Ethernet Controller, ASIC rev. 0xb002> irq 17 at device 0.0 on pci8 bge0: 0x10000 bytes of rid 0x10 res 3 failed (0, 0xffffffff). bge0: couldn't

Hi, Can you tell why my vnic built on top of an aggregation of 2 NICs of 1 Gbit/s doesn''t report a speed of 2 GBit/s ? [root at nazgul /]# dladm show-dev bge0 link: up speed: 1000Mb duplex: full bge1 link: down speed: 0Mb duplex: unknown bge2 link: down speed: 0Mb duplex: unknown bge3 link: down speed: 0Mb

On 2020-04-01 15:12, Greg Troxel wrote: > D'Arcy Cain <darcy at VybeNetworks.com> writes: > But yet, new packets from that IP address reach asterisk. It seems > almost entirely clear to me that you have a firewall problem, not an > asterisk problem. This could well be but Asterisk is the only thing that continues to communicate. > I would test this out with a remote

Hi, I have a system with a 4.11 Kernel. Unless I'm doing something very wrong, there seems to be something odd with ipfw. Take the following rules: ipfw add 00280 allow tcp from any to any 22 out via bge0 setup keep- state ipfw add 00299 deny log all from any to any out via bge0 ipfw add 0430 allow log tcp from any to me 22 in via bge0 setup limit src-addr 2 ipfw add 00499 deny log

Hi, this server, a Dell R720 has 4 bge on board, Broadcom NetXtreme Gigabit Ethernet, ASIC rev. 0x5720000 bge0: APE FW version: NCSI v1.1.7.0 bge0: CHIP ID 0x05720000; ASIC REV 0x5720; CHIP REV 0x57200; PCI-E miibus0: <MII bus> on bge0 ... I have connected the ethernet to port labeled 0, but it appears as bge2, how can this be corrected? thanks, danny

Hi, I have a system with a 4.11 Kernel. Unless I'm doing something very wrong, there seems to be something odd with ipfw. Take the following rules: ipfw add 00280 allow tcp from any to any 22 out via bge0 setup keep- state ipfw add 00299 deny log all from any to any out via bge0 ipfw add 0430 allow log tcp from any to me 22 in via bge0 setup limit src-addr 2 ipfw add 00499 deny log

D'Arcy Cain <darcy at VybeNetworks.com> writes: > Here is the first four lines from "pfctl -sr": > > pass in quick on bge0 from <FRIENDS> to any flags S/SA keep state > block drop in log quick on bge0 from <ENEMIES> to any > block drop in log quick on bge0 from <AUTOBLOCK> to any > block drop out log quick on bge0 from any to

On OpenSolaris 2009.06 I created a flow, half a dozen VNICs, and I set some properties, and everything was working, then I rebooted my system and everything disappeared from show-vnic, show-flow, and show-prop. When I tried to re-create the objects, dladm said they already existed. While I could not see the objects, I could delete them. Example: # dladm show-vnic # dladm create-vnic -l bge0

Howdy, I just finished reading through the Crossbow presentation: http://blogs.sun.com/sunay/resource/crossbow.pdf And have one question. If you create a virtual NIC with dladm: $ dladm create-vnic -d bge0 -m 0:1:2:3:4:5 -b 10000 1 Can you then add vnic1 directly to the zone? e.g.: zonecfg -z zone1 zonecfg:zone1> create zonecfg:zone1> set zonepath=/zones/zone1 zonecfg:zone1> add net

http://bugzilla.mindrot.org/show_bug.cgi?id=1014 Summary: SCP slow bandwidth with Solaris8 on n240 Product: Portable OpenSSH Version: 3.7.1p2 Platform: ix86 OS/Version: SunOS Status: NEW Severity: normal Priority: P2 Component: scp AssignedTo: openssh-bugs at mindrot.org ReportedBy:

All I got my samba server to join my win2k domain without any problems. But if I change the config to read security=domain it prompts the user for a username and password. If I change it to security=server it does not prompt for user names. I did some searching in the list came up with a few emails and this website http://www.sugoi.org/bits/index.php?bit_id=10 but still no change. In the /etc/host

Hello Samba List, I'm running a Samba 3.0.22 PDC on Solaris 9. Things got a bit peculiar when I added a 2nd network interface. The two subnets are a primary network that carries all the client traffic and a tape-backup/admin network that is not accessible to any clients, ie. aaa.bbb.ccc.241 - bge0 - primary network (address suppressed) 192.168.254.254 - bge1 - admin/backup network