similar to: Promise TX2 and ATARAID....... kjouirnald and kupdated seem to fight it out for reasourses

Hello, In some weeks I'm going to reinstall some old RedHat9 based servers with Promise FastTrak TX2000 "semi-hardware" RAID1 controllers. I just tried to install CentOS 4.0 on a computer with a spare card and as usual both HDD attached to the RAID1 controller are seen separately by the installer because the specific driver for the TX2000 wasn't loaded. Nothing new here, it

(Sent to linux-raid, linux-kernel and ext3-users since I'm not sure what type of issue this is) I've got a test system here running Redhat 7.1 + stock 2.4.9 with these patches: http://www.fys.uio.no/~trondmy/src/2.4.9/linux-2.4.9-NFS_ALL.dif http://www.zip.com.au/~akpm/ext3-2.4-0.9.6-249.gz http://domsch.com/linux/aacraid/linux-2.4.9-aacraid-20010816.patch All three patches applied

> Did you ever find out what was wrong? Nope, and personally I think there's a bug in 2.4.19. Since I sent the email below I did a make oldconfig and went thru the new options very carefully - no luck. I'm still running on 2.4.18, and I can compile a kernel, install, and it works fine. Randy Barton Hodges wrote: > Hi Randy > > Please pardon the intrusion, but I found your

Hi Everyone, Has anyone had any experience of using the Promise FastTrak SX4000 or SuperTrak SX6000 IDE RAID Controllers under Centos (if it matters I'm using version 4). I've seen it listed on linuxcompatible.org as working but would prefer to find out any first-hand experince before I buy. I'm looking to build a new mini server based on Mini-ITX and have found a great 1U case

I'm trying to install CentOS 4 on an A8V on the PATA/Raid drives on the Promise controller. The Promise controller is recognized (sata_promise), but the PATA drives are not recognized. Base on this thread https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=147303 it seems that there is a patch which was merged in 2.6.11 to get pata working. Any ideas how to proceed? Thanks in advance

anyone have experiences installing SATA raid card with CentOS/RHEL? I am considering Promise FastTrak S150 Tx2 plus, FastTrack 2200 or FastTrack S150 Sx4 Which one of these ( or any othe brand) can ensure smooth install of CentOS without problems, thanks. :)Harris LIU

Today our server had seriuos problems, we had to reinitiate it and run fsck manually. Dou you think it's an ext3, kernel (vanilla 2.4.19) or hardware bug? The errors were (from syslog): -------------------------------- Oct 6 16:10:25 nou kernel: attempt to access beyond end of device Oct 6 16:10:25 nou kernel: 72:02: rw=0, want=230266240, limit=4882432 Oct 6 16:10:25 nou kernel: attempt

Trying to install FastTrak TX2000 in box with CentOS 3.3 install. Just downloaded Redhat 8/9 driver from Promise but install says correct driver not found. Any suggestions? Is there a command to scroll --help files by the page... like DOS has /p -------------- next part -------------- An HTML attachment was scrubbed... URL:

Greetings - I'm looking to put some cheap storage into my server, which is running centos 3. I'm looking at the Maxtor SATA/150 PCI Card and a big maxtor sata drive. I would like to make sure that CentOS has driver for this controller. I looked in Red Hat's hardware database and did some google'ing but I couldn't find any info to confirm that this card is compatible.

Ive had two of them in the last two weeks.. The most recent kernel output is kernel: Unable to handle kernel NULL pointer dereference at virtual address 0000009c kernel: printing eip: kernel: c88132b4 kernel: *pde = 00000000 kernel: Oops: 0000 kernel: ppp_async ppp_generic slhc 3c509 8139too mii ipt_state ipt_LOG ipt_REJECT ipt_ kernel: CPU: 0 kernel: EIP: 0010:[<c88132b4>] Not

Hello CentOS, Does anyone know if there's a driver out there that'll enable CentOS 4.x to use the Intel Matrix SATA RAID settings on the 915 chipsets? -- Best regards, Mickael mailto:mike at kamloopsbc.com www.MickaelMaddison.com

I have a North American BRI configured as National ISDN (NI-1) on an SBC (Nortel?) switch. SBC calls this "FastTrak ISDN", and it's surprisingly inexpensive -- less than two POTS lines. I've been trying to find an inexpensive PCI interface solution to connect this to Asterisk as voice lines. I prefer ISDN BRI over POTS lines because of the improved signalling, fast dialing,

What kind of implementation software or hardware is recommended for ide Raid 1 with ext3? Some controllers from Promise like their new FastTrak TX2000 look nice. But won't I be tied into the kernel version that is only supported under their drivers? Is ide software Raid stable and fast with ext3 for a production system? Thanks in advance. Aaron Lopez

Trying to install FastTrak TX2000 in box with CentOS 3.3 (kernal 2.4.21-20.EL.c0) install. Just downloaded Redhat 8/9 driver from Promise. But "sh install" says correct driver not found on diskette. Any suggestions? Thaks -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, I'm using linux 2.4.25 and I'm trying to change the wakeup interval of kupdate daemon. Is there a way to change that ? I once used 'update' tool for that. But that is not there in 2.4.25. Has it been removed ? I appreciate any help regarding this. thanks, Vijayan

My system is RH7.2 with custom 2.4.18 or 2.4.19 kernel(s), downloaded from kernel.org. My root filesystem is ext3 on ataraid. I'm using initrd. My system comes up fine with 2.4.18 kernel, but when trying to boot a new 2.4.19 kernel I get the following sequence:

Hello! Has anyone gotten 4.9R to recognize the "ServerWorks CSB6" ATA controller on a Dell 600SC? How about installing 5.2R on a 600SC? 5.2R recognizes the said controller, but it corrupts data. -- eof

Hi, This morning I had some failed calls. On the console (and in the log) I saw the error "Unable to allocate channel structure". Before I restarted the process, I checked it's memory usage in ps and glanced at my free memory in top. Asterisk was using a normal ammount of memory, about 40M. I don't think this was a system limit. This was running Asterisk v1.0.2. Below is

I upgraded from 6.2 to 6.3 p5 last night. Upon rebooting, the second disk in the mirror is missing. # atacontrol status ar0 ar0: ATA RAID1 status: DEGRADED subdisks: 0 ad0 ONLINE 1 ---- MISSING # grep ata /var/run/dmesg.boot ad0: 238475MB <WDC WD2500AVJB-63UDA0 00.02C01> at ata0-master UDMA100 ad1: 238475MB <WDC WD2500AVJB-63UDA0 00.02C01> at ata0-slave UDMA100 ar0: disk0

Hello everybody! As I wrote in my mail the previous week ("BUG: 2.4.19pre1 & journal_thread & open filehandles") I followed the problem a little bit further. Here's my patch; I beg the ext3-maintainers (Stephen, Andreas, Andrew) to have a look at it and submit it to Marcelo and Linux for inclusion. (2.4 is for now for me more important than 2.5). Patch ----- On every