similar to: still can't print to samba printer from winxp

I am install Samba on a New RS/6000 M 80. I am installing Samba 2.0.7. I have the services and inedt.conf files with the needed entries and have add a program check my entry. I get the following error in the log file and can not figure out what is wrong. [2001/01/17 12:31:59, 0] lib/util_sock.c:open_socket_in(863) bind failed on port 139 socket_addr=0.0.0.0 (Address already in use)

I did a complete installation of Red Hat 7.2 on my Dell Inspiron 5000 laptop from RH6.2. I had SAMBA running on it fine until I wiped my hard drive and installed RH 7.2. So now I have to learn how to set up SAMBA with xinetd. I saw a newer version of SAMBA on the SAMBA.org web site so I downloaded it. After reading the INSTAll file and following the instructions it created an RPM in:

Hi, I installed Samba on Solaris to enable me print from the solaris workstation to a windows print server. When I start smbd and nmbd , smbd does not run but nmbd runs

Hi, I've just upgraded an old samba 3.0.23 on an old Fedora Core 5 to samba 3.5.4 using an rpm built from the source. Everything works fine, but when i start the server i get some error messages(see below). Before i start the server there is no connection (tested with lsof and fuser) on the 139 and 445 ports, smbd or nmbd aren't running. With the old version i never had this

Greetings All: I'm a newbie at Samba and have been attempting to get Samba to run on a BSD box with little success. Looking at hte /var/log/log.smbd file I get some wierd error message: [2003/07/28 13:18:36, 0] lib/util_sock.c:open_socket_in(804) bind failed on port 139 socket_addr = 0.0.0.0. Error = Address already in use Also, in the nmbd: [2003/07/28 13:18:41, 0]

SAMBA newbie here........New 2.2.8 install on 5.1 AIX, nmbd will not start. Here is my error: [2004/06/29 14:05:29, 0] lib/util_sock.c:open_socket_in(804) bind failed on port 137 socket_addr = 0.0.0.0. Error = Address already in use Any ideas? Thanks !!! Larry S. Singleton lars@thornwood.com Systems Analyst E-Mail Administrator/Webmaster/"Guru in Training" Thornwood Furniture

As soon as I start up the daemons using the following commands, nmbd dies. /usr/local/samba/bin/smbd -D /usr/local/samba/bin/nmbd -D When I view the nmbd.log it gives the following. We're trying to set up Samba to work over 2 subnets. Smbd is ok and we can still mount our shares. Does anyone have any suggestions? Thanks for any help. [2002/10/22 10:37:55, 0]

Samba was working well but I changed the host allow section of smb.conf and it stopped. I changed it back and restarted and got this error message in log.smbd [2003/08/17 12:15:26, 0] lib/util_sock.c:open_socket_in(789) bind failed on port 139 socket_addr = 0.0.0.0. Error = Address already in use I have a really simple smb.conf: # Samba config file created using SWAT # from localhost

Hello I'm a biginner on samba and mailinglists. But I desperate need same help. After updating my samba 2.2.1a to 2.2.2 I can't logon to the domain again. The log.nmdb gives out this information: [2001/11/02 01:22:28, 0] nmbd/asyncdns.c:start_async_dns(150) started asyncdns process 184 [2001/11/02 01:22:28, 0] lib/util_sock.c:open_socket_in(820) bind failed on port 137

I can't figure out what is causing the error message of [1999/10/13 11:39:42, 0] lib/util_sock.c:open_socket_in(671) bind failed on port 139 socket_addr=0.0.0.0 (Address already in use) in my logs and thus preventing smbd from serving up connections. How can I track down what is causing this? Samba has been working great and now I must have done something but I don't know what. The

I installed Samba 2.0.0 on a P100 running SlackWare Linux 96 (Kernel 2.0.0). After running configure, make, make install, and testparm, I thought I was all ready to start up the smbd daemon. So I typed in smbd -D -d 50 Got back a failure listing in the error log. [1999/02/01 16:27:06, 0] lib/util_sock.c:open_socket_in(663 Brian Lee Bowers | Division of Government Research Computer Aide I

Help please. I am in the process of configuring Samba 3.0.14a onto 4 AIX 5.3 systems. It seems to be working OK on 3 of the 4, but on the last one, I cannot start smbd. nmbd seems to start fine. The smb.conf file matches the other servers except that the server name is changed. Here's the error showing up on the log.smbd file. [2007/05/02 15:19:47, 0] smbd/server.c:main(835) standard

Help me ! I cannot start smbd, it immediatly stops, I've got in my log.smb [1999/05/19 14:53:43, 0] lib/util_sock.c:open_socket_in(709) bind failed on port 139 socket_addr=0.0.0.0 (Adresse déja utilisée.) And then It stops, I cannot launch smbd. I my /etc/services, I've got the two lines : netbios-ssn 139/tcp netbios-ns 137/upd and in /etc/inetd.conf netbios-ssn stream tcp

HI, I am running Red Hat 7.2 on a PC. Until today I have been able to start smb. Now I am no longer able to start smb. When I start it with /etc/rc.d/init.d/smb start it say OK. However, when I execute /etc/rc.d/init.d/smb status it says that smbd is stopped, but nmbd is running. If I execute smbstatus it says "Failed to open byte range locking database, Can't initialize locking module -

I get the following log when trying to run nmbd -D Netbios nameserver version 2.2.3a started. Copyright Andrew Tridgell and the Samba Team 1994-2002 [2003/05/20 15:02:44, 0] lib/util_sock.c:open_socket_in(789) bind failed on port 137 socket_addr = 10.10.50.4. Error = Cannot assign requested address [2003/05/20 15:02:44, 0] nmbd/nmbd_subnetdb.c:make_subnet(140) nmbd_subnetdb:make_subnet()

Freebsd 12.0-RELEASE-p10 samba 4.8.12 Recently, my machine has started going into an endless loop with the following message rolling off the screen continuously: nmbd_subnetdb:make_subnet() Failed to open nmb bcast socket on interface 0.255.255.255 for port 137. Error was Can't assign requested address

Hi. Today I upgraded samba from 3.0.34 to 3.4.4 without changing anything in smb.conf but with changing local and domain sid: old samba 1) net getdomainsid and getlocalsid new samba 2) net setdomainsid and setlocalsid to ones (both the same) from 1) after restarting samba I can't log into domain: XP says : domain controller unavailable ... I tried to rejoin domain - and I can ;) however

Bonjour, I have some problem to configure a printing server with samba. I have a private network with a linux box as a gateway to the internet and several machine on this network some under windows, others under linux. One of the linux machine (which is not the gateway) has a printer which I want to be shared by the windows machines. The gateway has 192.168.0.1 as private IP number and the linux

Hi, I am trying to install samba on the RHEL. The installation completes but after that I get the smbd dead message upon checking the status: [root@usps-dc1-pc12 share]# [root@usps-dc1-pc12 share]# service smb status smbd dead but pid file exists nmbd (pid 8078) is running... [root@usps-dc1-pc12 share]# The version of RHEL and samba are as follows:

On Fri, 16 Dec 2016 13:46:24 +0100 Artur Moor via samba <samba at lists.samba.org> wrote: > If I remove 'nmbd bind explicit broadcast = no' in 'smb4.conf', then > nmbd wan't start and I get following in the log: > > [2016/12/16 12:37:35.075428, 0] > ../source3/lib/util_sock.c:396(open_socket_in) > bind failed on port 137 socket_addr = 10.0.140.255.