similar to: Starting Udev

Hi I have had a Centos 5 installed with asterisk and zaptel for a couple of weeks, I had to reboot eh machine today, and when it rebooted it got stuck at "Starting udev" if I remove thew tdm400 it boots OK, but no zaptel has anyone seen this , and can offer any advice? Thanks Robb

I have a TDM400 with 2 FXS cards, and a Samsung 6100 DECT base station connected to one of the ports. The base station appears to only support UK (BT) style CLIP Caller ID signalling. Does anyone know if it is possible to configure the ZAP channel to send in this format, or alternatively can you recommend a GAP compatible base station which will handle both BT and Bellcore signalling? A search

Hi I have looked through the wiki and search the mailing list, but I cannot find a way to intrude on a call, can asterisk do this feature? if so how? Thanks for your help Robb

Hi All I'm having problems posting to this list, no bounces the mails just dont show any advice how to get the postings through is there filtering? robb

Hi All I cannot seem to find a way to stop atserisk inercepting DTMF tones and regenerating them even on a zap to zap bridged call is this possible? Thanks Robb

Hi, can anyone recommend a Linux based TFTP server to go on an asterisk box? Thanks in advance Robb

Hi I have a requirement to bridge Digital ISDN call through an asterisk box but no matter what I setup in the dial plan the second leg of the zap bridge is always set to Transfer Capability of SPEECH, I wondered if any one has come across this and managed to fix it? Thanks in advance for your help Robb

Hi List I'm trying to update to the lastest kernel but I have a dirver that is not inculded in the distrubution, and I had to use the driver disk when installing centos 4.4 in the first place, The driver megasr .ko works fine with the installed kernel but I cannot find on for the updated kernel, any adive would be appreciated. without the updated driver there is a kernel panic on boot due to

Hi I have a problem with a new DECT phone I have bought The key pad works like a Mobile phone where you dial first then pick up the line, but it seems to dail too fast or spuriously, ie 012826736464 show on thew Asterisk console as 0012282677, could any one offer advice how to fix? Also when doing a ZAP bridge to this phone from an outside line the call is very echoy, but not an internal

2008/10/5 robert.boardman at gmail.com <robert.boardman at gmail.com> > Kevin P. Fleming wrote: > > Olivier wrote: > > > > > >> 2. R Hook-flash key is now available to transfer calls. > >> In s450IP web management server, its defaults settings are : > >> Application-type: dtmf-relay > >> Application-signal: 16 > >> >

Hi All Just been looking at stats for one of my sites, and I'm conserned about the number of error cause codes being returned from the telco for example 12000 calls processed 131 are cause code 31* normal. unspecified.* 139 are cause code 28 * invalid number format (address incomplete).* 112 are cause code 1 *Unallocated (unassigned) number. *this adds up to about 3% of calls not

Hi, all I have installed TDM400 card. I can see it is there (lspci). But Asterisk does not find it. phonebox2*CLI> zap show status No Zaptel interface found. I assume that driver is not loaded, but I am sure I have installed it (I compiled zaptel and then re-build asterisk and did make install for both zaptel and asterisk). When asterisk is started I get: Jan 2 06:28:08 WARNING[3473]:

Don't you just hate it when something was working and when you come to use it in anger it's broken :-( Something in the, fairly, recent series of Asterisk updates has broken DIGITAL call passthrough. I've an ISDN PBX behind my Asterisk Box (PRI ISDN comes into port 1 of a Digium Wildcard and the PBX it connected to port 2 via an ISDN crossover cable). This PBX used to be able to

Hello List, I have been beating my head against the wall for a little while now trying to get my TDM400 card to work with Fedora Core 4. Not a great deal of success even after successful builds of zaptel and the other required componentry. The machine doesn't even recognize the card. Using Debian it was recognised but as a newbie to Asterisk most of the documentation I can find and

I have two questions about incomming ring and extension ringing 1) When an incoming call is detected by asterisk it takes 2 or three rings before the internal phone ring does anyone know how I can fix this? 2) All internal phone ring on an incoming pstn call but after the call is answer all the other phone ring for a couple of tinkles how can I stop this from happening? Thanks for your

Hi guys, I'm hoping I've made a silly mistake here, but I've been staring at the screen for the past few hours and I can't work it out. I upgraded to 1.2.16 recently, and am having problems with zaptel. The card is detected, I get a reasonable output from ztcfg -vv, and zttool shows the installed module (TDM400) with one FXS module. But when I start asterisk, I get

Hi, all Did anyone tried TDM400 card on old main board (Intel 440LX chipset -- PII)? The reason I am asking is because TDM400 needs PCI2.2 and main board is PCI2.1 I do not want to upgrade yet. Thanks, Rudolf

Hello everybody: This could be a stupid question, or may be not; I'm not sure 'cause I have not a very wide experience working with Asterisk, actually I just started last week. I need to make an IVR system work and I choose working with AGIs, written in Perl. The available documentation I've found show it as a very simple proccess, but it doesn't work for me... and I

Hi all, We have tested both tdm400 and BRI 1 port HFC based with mISDN driver and with both cards we have the same problem... so probably it's due to our misconfiguration, but we couldn't find anything useful on google. With TDM400 we can place and receive calls, but if we receive a call from TDM400 and we reject it from a sip phone , asterisk send the hangup but the line continue to

I have a TDM400 in the server. I want to press **1XX to pickup a call. It is ok if I pickup a call dialled from 1XX to 1YY (internal network call). However, it is failed to pick up a call from PSTN thro' TDM400 card. It seems I can't guess the correct context of it. How can I know the context of the call using CLI? The default context of the TDM400 is from-pstn but pickup still