similar to: link-dest storage saving on backup server not on usb hard drive

Long story short, my cat jumped on my server at my house crashing two drives at the same time. It was a 7 drive raidz (next time ill do raidz2). The server crashed complaining about a drive failure, so i rebooted into single user mode not realizing that two drives failed. I put in a new 500g replacement and had zfs start a replace operation which failed at about 2% because there was two broken

Hi, Can anyone explain the following to me? Two zpool devices points at the same data, I was installing osol 2008.11 in xVM when I saw that there already was a partition on the installation disk. An old dataset that I deleted since i gave it a slightly different name than I intended is not removed under /dev. I should not have used that name, but two device links should perhaps not

Hi and hello, I have a problem confusing me. I hope someone can help me with it. I followed a "best practise" - I think - using dedicated zfs filesystems for my virtual machines. Commands (for completion): [i]zfs create rpool/vms[/i] [i]zfs create rpool/vms/vm1[/i] [i] zfs create -V 10G rpool/vms/vm1/vm1-dsk[/i] This command creates the file system [i]/rpool/vms/vm1/vm1-dsk[/i] and the

Hi, im trying to attach another volume aka disk to win HVM, however it doesn''t seem to work: + xm block-attach win2008ss phy:/dev/zvol/dsk/pool1/win2008ss.dsk2 \ hdd:disk w 0 results in: elkner.sol ~ > + xm block-list win2008ss --long (0 (vbd (uuid 7cb8fadf-619d-dde6-bda9-dcc18023c7d5) (bootable 1) (devid 768) (driver paravirtualised)

Hello, I am trying to configure ZFS with IBM sdd. IBM sdd is like powerpath, MPXIO or VxDMP. Here is the error message when I try to create my pool: bash-3.00# zpool create tank /dev/dsk/vpath1a warning: device in use checking failed: No such device internal error: unexpected error 22 at line 446 of ../common/libzfs_pool.c bash-3.00# zpool create tank /dev/dsk/vpath1c cannot open

On Thu, Jan 08, 2015 at 01:44:58PM -0600, Gary R Hook wrote: > On 12/24/14 4:42 AM, Kashyap Chamarthy wrote: > >On Tue, Dec 23, 2014 at 12:38:57PM -0600, Gary R Hook wrote: > > > >[. . .] > > > >In my case, the block device is a QCOW2 disk image file. If I boot > >without using the disk image file which has the operating system, the > >domain will fail

I''ve just pushed vdiskadm import/export/convert to the 3.3 vdisk and vbox repos. You can now import a disk image from a block device or file to a vdisk, convert (in place) to a different type of vdisk and export from a vdisk to a block device or file. I''ve also pushed the full vhd support (sparse and fixed) and the ability to import a vmdk 1.1 optimized stream file. An

On 01/08/2015 12:44 PM, Gary R Hook wrote: > I've learned how to use the blockcopy command to create a local copy in > a simple disk file: > > virsh dumpxml my_domain > my_domain.xml > virsh undefine my_domain > virsh blockcopy --domain my_domain vda $PWD/dsk.copy.qcow2 --wait > --verbose --finish > virsh define my_domain.xml > > and the resulting copy in

Hello, I have a dual boot with Windows 7 64 bit enterprise edition and Opensolaris build 134. This is on Sun Ultra 40 M1 workstation. Three hard drives, 2 in ZFS mirror, 1 is shared with Windows. Last 2 days I was working in Windows. I didn''t touch the hard drives in any way except I once opened Disk Management to figure out why a external USB hard drive is not being listed.

I am trying to copy an 8 gig file. After first copying it over I try and rsync it again. There are no changes so why is it copying the file over again? Here is the output of what I am trying to do. And what does speedup mean? [root@VMWARE Storage]# rsync --verbose --recursive -t --stats -- progress ntapps.dsk vmware2::home/ [root@VMWARE Storage]# rsync --verbose --recursive -t --stats --

I''m attempting to expand a root pool for a VMware VM that is on an 8GB virtual disk. I mirrored it to a 20GB disk and detached the 8GB disk. I did "installgrub" to install grub onto the second virtual disk, but I get a kernel panic when booting. Is there an extra step I need to perform to get this working? Basically I did this: 1. Created a new 20GB virtual disk. 2. Booted

Hello, I?m using ZFS to export some iscsi targets for the virtual box iscsi initiator. It works ok if I try to install the guest OS manually. However, I?d like to be able to import my already prepared guest os vdi images into the iscsi devices but I can?t figure out how to do it. Each time I tried, I cannot boot. It only works if I save the manually installed guest os and re-instate the same

Hi, As I was experimenting with snv101, I discovers that every attempt to create a zpool gives this error: #zpool create pool1 c1d1s0 invalid vdev specification use ''-f'' to override the following errors: /dev/dsk/c1d1s0 overlaps with /dev/dsk/c1d1s2 I am testing with vmware, so I used the same virtual disk in a snv77 install, and I don''t get any error.

somehow I have issue replacing my disk. [20:09:29] root at adas: /root > zpool status mypooladas pool: mypooladas state: DEGRADED status: One or more devices could not be opened. Sufficient replicas exist for the pool to continue functioning in a degraded state. action: Attach the missing device and online it using ''zpool online''. see:

One of our Solaris 10 update 3 servers paniced today with the following error: Sep 18 00:34:53 m2000ef savecore: [ID 570001 auth.error] reboot after panic: assertion failed: ss != NULL, file: ../../common/fs/zfs/space_map.c, line: 125 The server saved a core file, and the resulting backtrace is listed below: $ mdb unix.0 vmcore.0 > $c vpanic() 0xfffffffffb9b49f3() space_map_remove+0x239()

- mkdiskimage -d image.dsk 2 64 32 - load it in dosemu and make it bootable with sys - isolinux: label 999 kernel memdisk append initrd=image.dsk harddisk c=2 h=63 s=32 results: memdisk 2.11 -> boots memdisk > 2.11 (up to 3.07) -> hangs The following message is printed in the boot messages > 2.11: MEMDISK: image has a fractional end sector The complete error message

(for some reason I cannot find my original thread..so I''m reposting it) I am trying to move my data off of a 40gb 3.5" drive to a 40gb 2.5" drive. This is in a Netra running Solaris 10. Originally what I did was: zpool attach -f rpool c0t0d0 c0t2d0. Then I did an installboot on c0t2d0s0. Didnt work. I was not able to boot from my second drive (c0t2d0). I cannot remember

Hi All: Using the following line, I am trying to install Scientific Linux (a RHEL derivative like CentOS), but the installer never sees my kickstart file : virt-install -n test-dev1 --ram=1024 --vcpus=2 --file=/dev/zvol/dsk/zfs_pool/xen/lss-kickstart1/root \ --file=/dev/zvol/dsk/zfs_pool/xen/lss-kickstart1/swap \ --file=/dev/zvol/dsk/zfs_pool/xen/lss-kickstart1/nfs \ --accelerate

Hi, when installing windows server 2008 Std hvm I get always a blue screen telling me: ''a clock interrupt was not received on a secondary processor within the allocated time interval'' I googled around and found, that this occured with vista as well: http://lists.xensource.com/archives/html/xen-changelog/2007-01/msg00170.html Config is: + virt-install --name=win2008ss

Team, **Please respond to me and my coworker listed in the Cc, since neither one of us are on this alias** QUICK PROBLEM DESCRIPTION: Cu created a dataset which contains all the zvols for a particular zone. The zone is then given access to all the zvols in the dataset using a match statement in the zoneconfig (see long problem description for details). After the initial boot of the zone