similar to: rsync without reverse dns lookup

Well FWbuilder is NOT easy. The documentation does not match the current GUI. Now the box is locked up. I will have to pull it again, hook it up to a kybd/VGA and reset iptables.... Maybe Shoreline with webmin.... Problem is I want a REAL router/firewall with little work. Both public and private nets have routable addresses. No NATing for me! I just help write the RFC ;) And all the

Well I think this system is back on 3.5. How do I tell? Have not used it in a while... I need a NAT for some quick testing and this box was available. Only a 6gb drive, so I can't install Astaro (which I have licenses for). So is there a simple way to turn on NATing? Should I upgrade to 4.2? This box is behind a firewall, so security risks are not the issue. This time.

I need a decent, easy, firewall on Centos. This is for test systems, so I do not need a lot. For 'a lot', I use and Astaro firewall. I had used Firestarter once, but found out that it cannot handle routing between a public and private network. Basically saying this is impossible. Of course, if your private network is addressed per RFC 1918 (that I co-authored), I can understand

Hi folks, I read quite some posts about "Destination host unreachable" problems before, but none could help me to solve my issue. So here we go: This is what I am using: SUSE Linux Enterprise Desktop 10 SP1 - Current with all updates Network configuration of my dom0: foobar:~ # ip a 1: lo: <LOOPBACK,UP> mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd

I have a broadcom bcm5722 and a dual intel pro/1000 pt nic in a dell t110. The setup sees the cards and i put them into automatic mode. After the install no cards are detected at all. Astaro 8.01 detects and utilizes all of these cards just fine. I have also tried ubuntu server 10.04 lts and they work fine. I'm curious if this is a bug with Centos 6?

What is everyone using for a firewall? I'm currently using www.astaro.com but their recent releases have soured me on ASL as a practical solution on my hardware (1.2MHz Athlon, 30G, and 256M). I only have 4 computers going through the firewall wall but it's consistently at 50% cpu load. There is very little network traffic (<10k bits per second on the wan connection, < 40k

Hi we bought an astaro firewall and are quite happy with it, now we need to buy a commercially supported LVS (linux virtual server) appliance. Does anyone have any good experience using any commercial LVS devices with web based GUI. --

CC init/version.o LD init/built-in.o LD .tmp_vmlinux1 drivers/built-in.o: In function `vmcoreinfo_show'': /usr/src/linux-2.6.18-xen.hg/drivers/xen/core/xen_sysfs.c:340: undefined reference to `vmcoreinfo_size_xen'' /usr/src/linux-2.6.18-xen.hg/drivers/xen/core/xen_sysfs.c:340: undefined reference to `paddr_vmcoreinfo_xen'' make[4]: ** [.tmp_vmlinux1]

Hi, Did anyone successfully installed and setup Astaro Security Linux V6 SIP Proxy with Asterisk behind the Astaro and clients bedinde another NAT? Regards ____________________________________________________ Start your day with Yahoo! - make it your home page http://www.yahoo.com/r/hs

Looks like globalize (1.2) is not compatible with rails 2.2.2. I am getting: '' => Booting Mongrel (use ''script/server webrick'' to force WEBrick) => Rails 2.2.2 application starting on http://0.0.0.0:3003 => Call with -d to detach => Ctrl-C to shutdown server ** Starting Mongrel listening at 0.0.0.0:3003 ** Starting Rails with development environment...

Hi, I made the switch from KDE4->XFCE, and because gdm takes more time than xfce to start I would like to replace it with lightdm. I installed lightdm, set it as default display manager and configured the gtk greeter. However, when I start I only get a black screen (x running) and nothing else happens. When I start it as root with the --test-mode argument, I get the following message: lightdm

Hi all, I would like to discuss a design idea I have in mind with you, in order to get critical feedback. ActiveRecord supports single table inheritance(STI) "per se", BUT you must add all possible instance variables(properties) of all subclasses to the "base table"(as columns). I would like to circumvent this restriction. Say we have a class AbstractGenericThing <

Dear all at the R-project help list. I have run into a problem when it comes to getting values for "total inertia" and "R-squared" for my DCA using "decorana" in the package "vegan". I have tried the "goodness" function, but the reply indicates that it does not work with "decorana" class objects. In Canoco one gets the Total inertia in

Dear people at the R-help-list. I have run into a problem in the package "vegan", while using the function "vegan", and would greatly appreciate any advice how to solve the problem. I have put in my data R, using the "decorana" function in the package "vegan" and received nice coordinates for the DCA of sites and species, as well as the Eigenvalues for the

Dear R Fundation, I am a post-doc researcher at the University of Pisa, Italy. I apologize for my english and I have to tell you in advance that I am a very beginner with R. I used R for fitting dose-response curves (drc package) and for an ordinary ANOVA (one, two or three factors), including the post-hoc mean comparison (I used the LSD test...). Now I have to process some simple data on

Hi! Following the three successful netfilter developer workshops 2001 (Enschede, NL), 2003 (Budapest, HU) and 2004 (Erlangen, GE), we are happy to announce the next event in this series. The workshop will be held in Seville, Spain. This year the workshop covers two sections: - Users conference from 3th to 4th Oct. - Developers workshop from 5th to 6th Oct, plus two extra days of hacking on

Is it possible to stream the content of a file using rsync to stdout instead of placing it into a file?

Hi, we are using Tinc in our Freifunk Network in Oldenburg for internode connections over the internet. So Tinc is running on OpenWrt 10.03 on Dlink Dir-300 Routers. We all have enough internet bandwith (1,6 MB/sec and more) but we only get a maximum speed of ~350KB/sec between two tinc nodes because then tinc uses 99% of the cpu. Is it possible to get more Speed with tinc on this machines?

http://bugs.freedesktop.org/show_bug.cgi?id=25795 Summary: windows not redrawn after resize Product: xorg Version: 7.4 Platform: x86-64 (AMD64) OS/Version: Linux (All) Status: NEW Severity: normal Priority: medium Component: Driver/nouveau AssignedTo: nouveau at lists.freedesktop.org

Dear list, is there anyone who successfully compiled a Samba 3.0.X on a Solaris 9 box? I tried severl versions of Samba 3.0.* on five rather differently configured Solaris 9 boxes (Sparc) and ALWAYS get a build error on dynconfig.c Sometimes it seems to be a missing ldap-preprocessor define (which is protested by the compiler although I configured --with-ldap=NO), sometimes it is a header file