similar to: Re: Help with USB-to-serial cable

I am trying to use software to program a scanner radio (BCD396t and UASD software). The software installs and seems to run properly, reading and writing database files. But I cannot connect to the scanner, through a USB-to-serial cable. OS: ubuntu-8.10, kubuntu-8.10, debian/lenny (tried them all) lsusb identifies the cable as follows: Bus 002 Device 002: ID 067b:2303 Prolific Technology, Inc.

I have a USB to serial converter attached to my box. pl2303: Prolific PL2303 USB to serial adaptor driver if I login to the box and send/receive serial commands over this unit it works without error EVERY time. however, if I run the same command set from with-in the extensions.conf with System() I get errors in dmesg like "pl2303 ttyUSB0: pl2303_open - failed submitting read urb, error

Hi All, I have an mge pulsar esv 14+ rackmount UPS connected via straight through serial cable to a USB to serial adaptor (My motherboard does not have a native RS232 port). I am running Ubuntu Server 9.04 x64, and nut 2.4.1-2ubuntu4 installed via APT. I am getting the error: Poll UPS [ups1 at localhost] failed - Driver not connected My conf files: (ups.conf) [ups1] driver=mge-utalk

thanks for these info. 2009/3/19 Artyom Mikhailov <artyom.mikhailov at gmail.com> > Hi there, > > Great project you have - NUT, thx for the development! > I just thought it might be usefull to let you know that APC SC1500I ups can > be found supported by NUT. > I used the following settings: > [sc1500i] > driver = apcsmart > port = /dev/ttyUSB0

hi! some time ago i have purchased card reader for scanning sim-card. it have usb inerface. in set was cd with soft (as usual only for windows) soft on cd: usb-driver installer sim max 5.16 & i try to run it on mandriva2008 kernel 2.6.22.9 first i try to install 'usb-driver installer.exe' then install sim max 5.16(it's 2 prog.: sim editor and sim scanner),but that's wrong way!

hello everyone, I've been testing the NUT solution as opposed to the undocumented LanSafe application to control my Eaton UPS. I am on a Slackware 13.37 system with a 2.6.37.6 kernel. NUT version is 2.4.3 . I installed the tarball by compiling it directly on my system (as a slackbuild package). The UPS is an Eaton Powerware 9155, but I don't know how to obtain the manufacturing date. The

Hi I am trying to connect a reliance netconnect data card on my linux box ( cent os ) , i am able to the detect the device /dev/ttyUSB0 these are the following steps I did : Check your card is recognized by the kernel # cat /proc/bus/usb/devices ..... ..... T: Bus=07 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 11 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P:

Hi! I'm having problems with SeaClear II v1.0.0.196. After setting up the symlinks in ~/.wine/dosdevices pointing to my gps-device (GlobalSat BU-353 USB) everything works as expected, but for some reason Wine/SeaClear steals all available CPU-time. 100% all the time. This problem does not exist if I start SeaClear with the GPS disconnected, making me belive there is a problem with

Ubuntu creates /dev/ttyUSB0 for me when I plug in the usb-to-serial-adapter. I have a symbolic-link to /dev/ttyUSB0 from 'dosdevices/com1'. What is new in 10.04 Ubuntu is that I have to sudo chmod o+r and sudo chmod o+w on /dev/ttyUSB0 every time before I start the app which uses that serial line. ttyUSB0 goes away when I unplug the serial adapter from the USB port or shut down the

Hello! I've ran into this annoying issue when setting up a new server. I have an APC SmartUPS hooked up on a USB-serial converter on /dev/ttyUSB0. This works nicely, until: hub 3-0:1.0: port 1 disabled by hub (EMI?), re-enabling... pl2303 ttyUSB0: pl2303 converter now disconnected from ttyUSB0 usb 3-1: pl2303 converter now attached to ttyUSB1 apcsmart gets into an infinite loop of this:

I am far from expert on these matters. But have a couple questions: 1. Are you sure that /dev/ttyUSB0 exists and is the result of the Prolific USB->serial converter? For example, if you yank the Prolific and reboot, is /ttyUSB0 there still? It is possible that there is another /dev/ttyUSBx out there.I doubt this but wonder. 2. I have recently been fuddled due to permission problems of

Hi all again, I found this kernel panic past days, now using the unsuported kernel and comes out again the same error. This time on '2.6.9-22.0.1.106.unsupported' kernel See attached logs, Env is the same with the same box, Hope it helps. TIA. JJ Garcia -------- Original Message -------- Subject: Kernel panic in usbserial. Date: Thu, 15 Dec 2005 12:09:53 +0100 From: J.J.Garcia

I am trying to access my GPS using wine 0.9.24 0n Suse 10.2 and Cxoffice 6.0 Beta 3a . Cxoffice 5.03 does not work at all with my Suse 10.2 installation. The Magellan road mate tools work well enough in both cxoffce beta and wine, however wine seems to handle it better when importing POI ( Points of Interest) files. Overall I think the wine included with Suse 10.2 is doing a better job -

Hi all, Running a Centos 4.2 default config in a P4 1.7 Mhz 512 MB Usb 1.1 (Acer Aspire 1400 XV Laptop) with a usb2serial interface plugged from the system boot, and using that line as console line for a remote device, i had the following kernel panic after few times performing the "reset" command in the gnome-terminal due font corruption, i had this kernel panic: Dec 14 23:58:10

Hello everyone and best wishes for 2023 :) I have an old *Garmin Drive Smart 50 GPS* and I want to be able to attach it when it is in preboot mode to a VM hosted by a *Debian 11 host*. From what I understand, the preboot mode allows us to flash a firmware before the GPS actually starts (used among other things when the GPS is soft bricked). When I connect the GPS to the host it gives:

Hello, I have two SMS PowerVision PV2200 BIFX, that came with a serial port, I used a serial - usb conversor to conect it to my pc it recognized as: lsusb -s 001:005 -vvv Bus 001 Device 005: ID 067b:2303 Prolific Technology, Inc. PL2303 Serial Port Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 0 (Defined at

Hi Charles! Thanks a lot for your response. Now I figure why the isbmex driver was not working. On the other hand I've tried to run the command suggested. But no success. I got this information when running the dmesg command after running the modprobe $ sudo modprobe ftdi_sio vendor=0x0483 product=0x0035 [35816.111760] usbcore: registered new interface driver usbserial [35816.111792]

Hi Users NUT, I want monitor a UPS of brand SMS (Sinus Double 8 KVA) using a raspberry-pi. In compatibility list, is listed to use the blazer_ser driver. I use a USB adapter to RS-232 conected in to the No-Breake. Follow the comands e confs. root at rasp:/home/pi# lsusb *Bus 001 Device 004: ID 067b:2303 Prolific Technology, Inc. PL2303 Serial Port* Bus 001 Device 003: ID 0424:ec00 Standard

Hi everybody, I am installing an Upsilon 2000 UPS via USB adapter on a RedHat 9 and I cant make that the device communicate correctly. Please any help will be welcome dmesg attached Thanks Gonzalo Red Hat 9.0 2.4.34.1 #dmesg usb.c: registered new driver usbdevfs usb.c: registered new driver hub usb.c: new USB bus registered, assigned bus number 1 usb-uhci.c: $Revision: 1.275 $ time 15:28:15

Hello, I have a strong suspicion that something is not working right on my el6 laptop. I have a usb 3g dongle that works fine on windows and ubuntu. It's one of those ZTE dual-personality devices (usb id 19d2:2000). When it's plugged in, it appears as usb storge device, then needs to be ejected, then it appears as usb modem with few serial ports. This is handled properly by udev on