similar to: Cut and paste

(REPOST, sorry if you get this more than once.) Hello all, (Not sure if this is more appropriate for user or dev list) Does asterisk have any sort of "standards based" api that can enable an application to do call control on the switch ? For example, if I am developing a call center application using asterisk, I would like to be notified of inbound calls and then be able to route

Hi everyone Firstly, apologies for the cross post, I am not sure which list is most appropriate for this question. I should also point out, that I did not install OCFS2 and I am not the person that normally looks after these kind of things, so please can you bear that in mind when you make any suggestions (I will need a lot of detail!) The problem: accessing certain directories within the

Hi everyone Firstly, apologies for the cross post, I am not sure which list is most appropriate for this question. I should also point out, that I did not install OCFS2 and I am not the person that normally looks after these kind of things, so please can you bear that in mind when you make any suggestions (I will need a lot of detail!) The problem: accessing certain directories within the

Can I somehow configure Linux so that it automatically detects win32 binaries and executes them using Wine? Thanks, David

Greetings: Ouch, that's not good. I can tap into the stream just fine with 'xmms http://64.108.112.135:8000/shouter.ogg' but not by clicking on the same address as a link. More debugging ahead... ;) Btw, I've restarted the stream. Thanks for the report ! Best regards, == Dave Phillips The Book Of Linux Music & Sound at http://www.nostarch.com/lms.htm

Greetings: Ouch, that's not good. I can tap into the stream just fine with 'xmms http://64.108.112.135:8000/shouter.ogg' but not by clicking on the same address as a link. More debugging ahead... ;) Btw, I've restarted the stream. Thanks for the report ! Best regards, == Dave Phillips The Book Of Linux Music & Sound at http://www.nostarch.com/lms.htm

Dear All, I have a data sets as shown below A (Patient ID ), B and C are the Concentration of drug in blood on day 1 and day 4, D is the difference in conc. To do this in R I have written a code as follows, identified the number of patients who have more concentration on day 4 . Here I want to identify specifically the patient ID (is he patient 1 or 2 or 5 and 7), whose concentration is more. How

Is there a way to get Wine to use Render extension in XFree86 4.0.3 to allow it to have antialiased fonts? David

In bits.c\speex_bits_pack there is logic to reallocate the bits buffer. In that section there is a call to speex_memset_bytes which appears to wipe out all the old bytes. I found when I encoded a multi-frame message that needed less than the default 2000 bytes for bits->chars, everything worked fine. However, when I encoded a longer message that triggered the realloc code in speex_bits_pack,

I have been using the Speex NB mode with an 11025 kHz signal, without adjusting the framesize, and it's been sounding just fine to me. However I was wondering what the best way to make 11025kHz would be. I also have an audio driver that uses 2kB buffers, and the NB framesize of 160 doesn't divide evenly into that so I end up having to shovel tails of buffers around which isn't too

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Is there a lot of overhead in sending and ogg container stream(containing video and audio) via RTP, or would it be better to just send the two streams separately via RTP? Thanks, David - -- If you give someone a program, you will frustrate them for a day. If you teach them how to program, you will frustrate them for a lifetime. -----BEGIN PGP

I must set up a backup server for failover and have used tdbbackup to create backup files from the functioning primary server. I then copied the files to the backup server and used tdbbackup to restore all the databases, along with copying the smb.conf and other text files from /etc/samba. This does not seem to work and I was hoping someone could assist. Primary server is RHEL 5.4 with Samba

I am using R version 2.6.2 (2008-02-08) on an XP Pro (version 2002 SP2). When I try to load the R library 'gtools', I get the following error: >library(gtools) Error in .Call("R_lazyLoadDBfetch", key, file, compressed, hook, PACKAGE = "base") : C symbol name "R_lazyLoadDBfetch" not in DLL for package "base" Any help or suggestions would be

I wish Speex could come with instructions on how to build libspeex_armce.lib. ________________________________ From: speex-dev-bounces@xiph.org on behalf of speex-dev-request@xiph.org Sent: Mon 11/13/2006 3:01 PM To: speex-dev@xiph.org Subject: Speex-dev Digest, Vol 30, Issue 15 Send Speex-dev mailing list submissions to speex-dev@xiph.org To subscribe or unsubscribe via the World

Kirk, Speex was designed for 8kHz, 16kHz, and 32kHz sample rates. If you don't use one of these sample rates, you'll be messing up important assumptions deep within the codec. Why these sample rates? It's telecommunications tradition, rather than PC audio tradition. If you want an efficient and high quality format for voice chat, try 16kHz with VBR quality 6. You should see

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Is it possible to add "bookmarks" to an ogg file? I've got a project we're I'd like to be able to set bookmarks at specific times in a file and identify them by id's like "part 1.1" etc. Anyone know if it's possible? Also would it be possible with Ogg speex? Thanks, David - -- If you give someone a