similar to: lm_sensors on Sun (x86) Hardware

Hey guys and gals, Anyone have any experience with getting lm-sensors to run on Sun hardware? In particular Sunfire x2250 and x4170 I was running 5.3 on these boxes and sensors-detect would not find anything. I did a bit of research and as I recall thanks to this list discovered some bugs that were affecting me, so upgraded to 5.7. CPU temp sensors were then detected, but no fan sensors. At

Sorry if this has been around many times before, but I've done quite a bit of reading and searching for some type of human readable guide for setting up the lm_sensors for hardware monitoring. I've dorked around with the stuff in the system here, but after looking at the /etc/sensors.conf, I don't think I want to delve into that and try to pull out the right group of settings.

Problem and solution, not sure if correct After upgrading to 5.1 and restarting, lm_sensors complained "General Parse Error." Google pointed here: http://www.lm-sensors.org/wiki/Devices Where I found this under "SENSOR CHIP DRIVERS - STATUS" AMD --> "Since Kernel 2.6.19" Latest AMD K8 processors have integrated sensors which can be read directly without any

On Wed, Apr 1, 2020 at 12:33 PM Peter Kjellstr?m <cap at nsc.liu.se> wrote: > On Wed, 1 Apr 2020 10:01:04 +0530 > Thomas Stephen Lee <lee.iitb at gmail.com> wrote: > ... > > Thanks for the information ?. > > Rented a new EPYC Rome Server from Hetzner, but sensors does not show > > status of all cores in list, which is why I asked. > > Curious what

hello, I have problem to install lm_sensors on CentOS 4.5 (Linux 2.6.9-42.ELsmp). I am getting error message "FATAL: Module bmcsensors not found." after I enter "modprobe bmcsensors". I got advice to install http://bmcsensors-26.sourceforge.net/ into my kernel, but I don't know how to do it. Does somebody has experience how to get lm-sensors working on CentOS 4.5 ?

Hey folks, I have 1 system ( Sunfire x2250 running 5.7 ) that is having issues with RAM, but I'm not sure how to debug it. And unfortunately it is not under support anymore. I started the job about 4 months ago and when I came aboard the guy who handed stuff over to me told me this issue was on his list of things he was unable to get to yet. He told me he'd seen errors in the past in

Hi, Is there a way to make use of hardware monitoring on Intel 945GCLF (with Atom 230 cpu)? It is relatively new child of Intel, but maybe someone figured it out yet. pciconf -lv shows this: ichsmb0@pci0:0:31:3: class=0x0c0500 card=0x464c8086 chip=0x27da8086 rev=0x01 hdr=0x00 vendor = 'Intel Corporation' device = '82801G (ICH7 Family) SMBus

Hey folks, I have a Sun J4400 SAS1 disk array with 24 x 1T drives in it connected to a Sunfire x2250 running 5.8 ( 64 bit ) I used 'arcconf' to create a big RAID60 out of (see below). But then I mount it and it is way too small This should be about 20TB : [root at solexa1 StorMan]# df -h /dev/sdb1 Filesystem Size Used Avail Use% Mounted on /dev/sdb1 186G 60M

Hi all :) Using lm_sensors, I can see few temperature indicator. M/B Temp: +39?C (low = +15?C, high = +40?C) sensor = thermistor CPU Temp: +33?C (low = +15?C, high = +45?C) sensor = thermistor Temp3: +53?C (low = +15?C, high = +45?C) sensor = diode What is that Temp3? It's the hottest. Which one is the best to use if I want to use lm_sensor as a general

I don't think this is off topic since I want to use JBOD mode so that Linux can do the RAID. I'm going to hopefully run this in CentOS 5 and Ubuntu 12.04 on a Sunfire x2250 Hard to get answers I can trust out of vendors :-) I have a Sun RAID card which I am pretty sure is LSI OEM. It is a 3G/s SAS1 with 2 external connectors like the one on the right here :

Last week I upgraded my box to CentOS 6 and I'm very impressed so far with it. The only small issue so far is that it doesn't seem to recognize the new Sandy Bridge Core i5 CPU that I have and you can't monitor its temperature. I recompiled the latest coretemp module from the latest 2.6.39 kernel and the latest lm_sensors version however this still wasn't enough as the new module

Hi All, I'm trying to get lm_sensors to work on a Shuttle with an AMD K10. The version of lm_sensors in the main CentOS repo is 2.10.7, which is two years old now. Support for the K10 was added about a year ago. So, does anyone know if there are binaries available for more recent versions of lm_sensors? Also, if anyone has knowledge of the sensors layout for recent Shuttle AMD motherboards,

On Monday 12 December 2016 11:01:52 Nicolas Kovacs wrote: (first thing I'm going to do it buy a new keyboard, or employ a proof reader. Sorry for all the errors folks) > > First thing I would do is check the temperature. In my experience, > excessive heat is the main reason for unexpected shutdown operations. I have had this in the past where either the CPU or PSU fan had died.

On Monday 12 December 2016 12:15:10 David Both wrote: > The lm_sensors package is required for the sensors module of glances to > work. After installing lm_sensors, run sensors-detect. The sensors > command will show the sensors detected and their current values. glances > should then display the sensor readings. Somewhere tucked in the back of my mind a memory is screaming no.

hi all, I am trying to get lm_sensors to work. did the yum install lm_sensors service lm_sensors start sensor -s and it says no sensors found. did lsmod | grep it87 and it87 57061 0 hwmon_vid 35905 1 it87 hwmon 36553 1 it87 i2c_isa 39105 1 it87 i2c_core 56129 5 it87,i2c_isa,i2c_dev,i2c_ec,i2c_piix4 Seems like

Hello folks, I'm having a difficult time trying to figure out why the CPU cooling fans run at full speed on my Supermicro X8DAL-3 motherboard. There doesn't seem to be any variable speed (the fans are PWM compatible) ... they either idle at almost nothing, or suddenly burst into a high-pitched scream that gets my ears bleeding after a few seconds. Once they jump to warp-10, they

Dumb question: how do you start lm_sensors' fan control at boot time? Centos 6 here

Hi! I have an vb8001 and i try to make the lm_sensors to work .. i upgraded to latest version and in the end doesn't find the vt1211 driver ... is it packaged somewhere? (maybe elrepo but it doesn't find any vt1211 nor 1211 related packages) (of course this is on an Centos 5.4) Thanks, Adrian P.S. i tried to post to lm_sensors mail list but it seem that it is not working (nor

Hi all, New to the list and (mostly) new to CentOS. We have just moved from running RHEL to CentOS on our main production servers. Anyway, I am configuring a couple of new SunFire v20z servers here at the moment and trying to get the systems' management interfaces to work fully under CentOS. First issue was trying to install the openipmi RPM from the CD that came with the SunFires, this RPM

I found that lm_sensors got installed because of a dependency on my first Xen VM that I updated to 5.3. lm_sensors doesn't make sense in a VM. I thought, ok let's check after the update who wants it. However: rpm -q --whatrequires lm_sensors no package requires lm_sensors (same for --triggeredby with lm_sensors or the packages below) Trying to remove lm_sensors reveals these packages: