similar to: 2 Ethernet cabling question

> I've never bothered to check to see if cat5 cables use the appropriate > mating twisted pairs or not. Since the pinouts are different for cat5 vs > T1 cables, I'd have to guess a single strand is used from two different > twisted pair groups. That wouldn't be cool, but in short runs it > probably doesn't have much of an impact. > IIRC, standard Ethernet uses

I'm looking to connect a BMC 450 to an asterisk with a Digium Quad E1 card. Am I right in thinking that I'll need a special 'crossover-E1' RJ45 cable? If so, any clues where I might buy one in the UK? The Digium card sellers don't seem to stock such a thing. Thanks. Tim. Tim Panton - Web/VoIP consultant and implementor www.westhawk.co.uk

Dear fellow R users, I would like to draw a "sunflowerplot" because I have data (decade by month) that plots multiple times on the same x-y co-ordinates. Further I would like to colour each of the points/sunflower leaves on the plot according to the group they belong to (i.e. which type of event each represents within that decade and month). I thought that this would be relatively

> I looked at your network diagram. Try checking the configuration of the > Ethernet ports on the firewall and the Asterisk box. Make sure they are > set to auto-negotiate and not set to a fixed speed and fixed duplex. > I have found in the past that if one end of a link is expecting auto- > negotiation (as the switches probably are) and the other end is expecting > a fixed

The "telco guys" probably did something non-industry standard and reversed send and receive in the jack that they plugged the CAT5 into. Sure it works, sure it is easier, sure it is not the correct way of doing things. Thanks, Steve ________________________________ From: asterisk-users-bounces@lists.digium.com on behalf of Lacy Moore - Aspendora Sent: Sat 4/22/2006 2:55 PM To: Paul

Hello, I want to plot 6 line graphs. I have 10 points 0.1, 0.2, 0.3, 0.4, 0.5, 0.6, 0.7, 0.8, 0.9 and 1.0. At each point say 0.1, I have 6 variables A, B, C, D, E and F. The variables all have values between 0 and 1 (and including 0 and 1). I also want to label the x axis from 0.1 to 1.0 and the y axis from 0.1 to 1.0. My goal is to plot a line graph representing the mean of the variables at each

I have the following problem. I want to use pairs function and get a matrix of scatterplots with the correlations in the upper panel and the ordinary scatterplots in the lower panel. Moreover, I want to have points colored in five differet ways in the lower panel, because I have five subgroups. In order to do that I tried to combine examples on pairs function help. I got a colored matrix

Charles and Manuel, Thanks for the help. Charles pointer to the IP address that was 'not listening' gave me the hint. I had assigned the listening interface to the crossover cable connected network cards link between the two nodes. I changed it to the switch connected network cards and bingo. The lack of power in the other node was telling the surviving node on reboot that the

so first off wow works on wine but wines being gay and when i hit maximize it maximizes but the actual wow window is still the same size and i have problems running tf2 on crossover it tells me "Setup file 'gameinfo.txt' doesnt exist in subdirectory 'hl2'. Check your -game paramater or VCONFIG setting.and tf2 works fine if i just switch over to ms home edition by restarting.

I am hoping to replace my Nortel 8x24 switch with Asterisk. Right now my cabling comes from my outside phone box into my office and into a punchdown block and leaves the punchdown block as an amphenol connector which currently plugs into the Nortel swicth. A second amphenol connector them plugs into the switch and extends to another punchdown block that I believe carries the lines throughout the

Say I had a crossover cable that connected a Mitel SX200 to a TE110P and the pinout was done as such: 1 - 4 2 - 5 5 - 1 4 - 2 (the 5 and 4 are transposed on the left side) Instead of the proper way of: 1 - 4 2 - 5 4 - 1 5 - 2 What would the results be? We have had the former as our cabling for a few months and the connection has been fine. Slip errors here and there. But we have had major

I have two DELL servers with two Ethernet ports in it. Bith servers have CENTOS 4.5 installed. First Ethernet port connect to public Ethernet line and work correctly. Second Ethernet port I connect point-to-point as private Ethernet (cable direct connect without router or switch). Private Ethernet use IP asddress 1.1.1.1 and 1.1.1.2. I check "ifconfig -a" and both eth0 and eth1 are

On 02/13/2017 04:39 PM, Charles Lepple wrote: > On Feb 13, 2017, at 8:08 AM, Tim Richards <tims_tank at hotmail.com> wrote: >> Feb 13 23:11:42 systemd[1] Starting LSB: UPS monitoring software (deprecated, remote/local)... >> Feb 13 23:11:43 usbhid-ups[2093] Startup successful >> Feb 13 23:11:43 upsd[1 932] Starting NUT UPS drivers ..done >> Feb 13 23:11:43 upsd[21

Greetings list, I've been asked to provide a system for 200 extensions, most of which will be existing analogue POTS handsets, not IP handsets. I've not really had any experience with large channel banks in the past (since most of our deployments are strictly IP-only to the desk), so I'm at a loss as to which ones are worth looking at. If anyone's had experience using channel

Calling all Definity admins, Got a few questions about Definity -> Asterisk interoperability. 1) What are the options for integration? Can I hand off extensions from the Definity and vice versa? 2) Anybody have any working configs they would like to post? I've found and read the legacy integration on the wiki about the two systems. I've also googled and found a few threads that were

I am trying to connect two machines to each other with an T1 crossover cable. The first machine has two TE120P cards - one connecting to the telco on an ISDN PRI. The second to a crossover T1 cable to a second machine which has one TE120P card. Telco <-cA-> Machine1 <-cB-> Machine2 Machine1: Two TE120P cards Machine2: One TE120P card cA: Standard T1 Cable cB: Crossover T1

> Close. 10/100mbps Ethernet uses wires 1,2,3,6 but that is pair 2 & 3. > Pair > one is the pair up the dead center (pins 4&5), pair 2 is pins 1&2, pair 3 > is > 3&6 and pair 4 is 7&8. A T1 uses pairs 1&2, which is why you can't use a > regular crossover cable for a T1 crossover, but you can use a regular > ethernet patch cable as a T1 patch

I'm connecting a T1 PCI card to a Nortel Option 61 switch T1 card. My Sangoma A102D shipped with 2 T1 cables - which I assume are straight through. Do I need to make crossover cables for this scenario? Thanks -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20071026/9cea5e74/attachment.htm

Hi all, I have the following problem. A Linux box configured as a bridge. One interface connects to the router via a crossover cable, the other connects to a switch via the cable that used to go to the router. Now I get the following: [root@localhost net]# ifconfig eth3 eth3 Link encap:Ethernet HWaddr 00:03:2D:07:61:5D UP BROADCAST MULTICAST MTU:1500 Metric:1 RX

Does anyone have any experience getting a Mitel SX-200 EL/ML PBX system to work with *? I'm not getting inbound or outbound calls to work. (Inbound caller gets line busy tone.) SETTINGS FROM MITEL: I built a Crossover cable and connected it like this: PSTN--T1--ASTRISK--T1--OLD MITEL -Crossover Cable Pin-out: 1 - 4 2 - 5