similar to: Gnome mouse configuration.

Hi Gang. I installed CentOS last night and the sound card detection failled to detect the sound card. I have a Asrock K8NF6G-VSTA mother board, with a nVidia NF6100-405 chip set. I have tried various live distro's and I ran Fedora 7 on it for just over 2 weeks and none of them detected the sound card. I'm a newbie to Red Hat based distributions but have been using Mandriva for

Hi Gang. I installed CentOS last night and the sound card detection failled to detect the sound card. I have a Asrock K8NF6G-VSTA mother board, with a nVidia NF6100-405 chip set. I have tried various live distro's and I ran Fedora 7 on it for just over 2 weeks and none of them detected the sound card. I'm a newbie to Red Hat based distributions but have been using Mandriva for

Hi, I am new to this list, so I apologize if I make any mistakes in posting. I am trying to set up nut with my Tripp Lite SMART 1200LCD. I looked on the compatability page, and some Tripp Lite models were supported, so I decided to try out mine. I have tried both USB and serial connections, and neither have worked. I am just wondering if this is a problem with nut supporting my model, or

I have experienced the problems with trying to use USB in VMWare Server 2.0. I have read in various places that it involves the settings of some permissions in the /proc file system, but most of the information has been of the "check your permissions on /proc/bus/usb", but nothing to tell what they should be, or what the ownership of the "file" should be, or how to keep

Hello. It is update of my previous message. I''ve checked that I can passthrough discrete graphic card, but when I try use in IGP (without discrete card in the slot) linux come to desktop without usage in inteldmr driver indeed. Dmesg show that I have some problem with ioremap. Is someone tried do pci/vga passthrough of integrated graphic or know way to solve that problem? Best regards.

I have a new system which includes a Plextor PX-740a DVD+-R/RW CD-R/RW drive attached to an Asus A8V-MX motherboard. When I try to use burncd to burn a cd, it writes all of the data, says "fixating CD, please wait.." and then reports burncd: ioctl(CDRIOCFIXATE): Input/output error Oddly enough, the CD seems to be usable. I can successfully burn the same file if I use cdrecord. The

To all, I attempted to configure the UPS tools for the Tripp-Lite SmartOnline 1500VA 2U rackmount UPS. I followed the instructions from the 'upsdrvctl start' output and posted the diagnostic information below. Is my UPS using an unknown product ID as reported? From the mailing list archive, I have found another posting for the same UPS with device model '09AE/4003', whereas

<message resent - email address not valid, I apalogize if you received it twice> I have the same problem than Volker Stolz a month ago! If I boot with the hub attached, it stops at : ohci0: <AcerLabs M5237 (Aladdin-V) USB controller> mem0xdf000000-0xdf000fff irq 9 at device 2.0 on pci0 usb0: OHCI version 1.0, legacy support usb0: <AcerLabs M5237 (Aladdin-V) USB

I have a Belkin F6H500ukUNV ups that I am attempting to get working under nut, however it does not appear to be detected by nut, I'm assuming that I need to feed some information back to you guys to get it included in the database somwhere. I've included (what I can think might be) the relivant outputs. Please let me know if you require anything else. dmesg output /sbin/newhidsups

I have an Asus A8V-MX motherboard with an AMD Athlong 64 X2 3800+ CPU and I'm trying to run powerd to keep it cooler/quieter/greener. I'm running -STABLE (6.1-RC) cvsup'ed a couple of days ago, with a kernel config that consists of the SMP sample plus an atapicam device. I'm loading the cpufreq.ko module in /boot/loader.conf. I've attached my dmesg output and sysctl -a

Hi, I am trying to attach a Palm Z22 via USB to my fully virtualized Win XP. Dom0-System: CentOS 5.3 x86_64 (Kernel 2.6.18.128.1.10.el5xen) XEN: 3.0.3-80.el5_3.2 XP: 32-Bit Professional lsusb shows: USB Palm: Bus 002 Device 007: ID 0830:0061 Palm, Inc. Lifedrive / Treo 650/680 / Tunsten E2/T5/TX / Zire 21/31/72 / Z22 I found some hints that I have to put usb = 1 and usbdevice =

Aloha! Concisely, I''ve been trying for several days to get VGA/PCI passthrough working. Regarding VGA vs PCI passthrough, I''m not entirely certain of the difference? Does Xen perform a different set of operations when passing through a VGA card versus any PCIe card? I''ve read the wiki and it seems the answer is "yes;" however, when passing through a

Hello Sir, Copid cmdcons and cmldr to O:(my usb drive) as follows (1) Microsoft(R) Windows 98 (C)Copyright Microsoft Corp 1981-1999. C:\WINDOWS>format o: /s C:\WINDOWS>format o: /s WARNING, ALL DATA ON DISK DRIVE O: WILL BE LOST! Proceed with Format (Y/N)?y Checking existing disk format. Formatting 967.98M Format complete. System transferred Volume label (11 characters,

I'm trying to run Palm Desktop, following James Littett's HOWTO. Step 1 is "Start Hotsync on WINE. Enable network syncing" I get [les@bilbo ~]$ wine "/home/les/.wine/drive_c/Program Files/palmOne/HotSync.exe" fixme:shell:DllCanUnloadNow stub err:module:import_dll Library USBPort.dll (which is needed by L"C:\\Program Files\\palmOne\\USBTransport.dll") not