similar to: multipath

hi all We have a rh linux server connected to two HP SAN controllers, one an HSV200 (on the way out), the other an HSV400 (on the way in). (Via a Qlogic HBA). /etc/multipath.conf contains this : device { vendor "(COMPAQ|HP)" product "HSV1[01]1|HSV2[01]0|HSV300|HSV4[05]0" getuid_callout "/sbin/scsi_id -g -u -s /block/%n"

I have worked quite a bit with CentOS 4.x with SAN, multipathing, LVM etc. The way I mount my file systems is using a script that is called during startup that runs fsck, imports the physical volumes, and volume groups, activates the logical volumes, creates the mount point if needed then mounts the volume, I mainly made it for software iSCSI due to the iscsi stack loading after the system mount

Hello, I have installed ocfs2 without problem and use it for a RAC10gR2. Only Clusterware files are ocfs2 type. multipath is also used. When I issue : mounted.ocfs2 -f I have a strange result: Device FS Nodes /dev/sda ocfs2 Unknown: Bad magic number in inode /dev/sda1 ocfs2 pocrhel2, pocrhel1 /dev/sdb ocfs2 Not mounted /dev/sdf

Dear fellow CentOS users, I have never experienced this problem with hard disk management before and cannot explain it to myself on any rational basis. The setup: I have a workstation for testing, running latest CentOS 7.3 AMD64. I am evaluating oVirt and a storage-ha as part of my bachelors thesis. I have already been running a RAID1 (mdraid, lvm2) for the system and some oVirt 4.1 testing.

I am attempting to get multipath working with device-mapper (CentOS 4.2 and 4.3). It works on EVERY install of mine from RH (also v4.2, 4.3), but the same multipath.conf imported to all my installs of CentOS do not work. Note that I have tested a working 4.2 configuration file from RH on CentOS 4.2 and a working 4.3 configuration (it changed slightly) on CentOS 4.3. Neither worked. Our production

Hi there. I have 2 servers with this number of disks in each side: pve01:~# df | grep disco /dev/sdd 1.0T 9.4G 1015G 1% /disco1TB-0 /dev/sdh 1.0T 9.3G 1015G 1% /disco1TB-3 /dev/sde 1.0T 9.5G 1015G 1% /disco1TB-1 /dev/sdf 1.0T 9.4G 1015G 1% /disco1TB-2 /dev/sdg 2.0T 19G 2.0T 1% /disco2TB-1 /dev/sdc 2.0T 19G 2.0T 1%

If it's replica 2, you can loose up to 1 replica per distribution group.For example, if you have a volume TEST with such setup: server1:/brick1 server2:/brick1 server1:/brick2 server2:/brick2 You can loose any brick of the replica "/brick1" and any brick in the replica "/brick2". So if you loose server1:/brick1 and server2:/brick2 -> no data loss will be experienced.

I''m setting Xen3.0.4 with CentOS5.2 I don''t know what exactly needs to add. So I make ramdisk with following command. : mkinitrd -v -f --with libata --with sd_mod --with sg --with ext3 --with scsi_mod --with jbd --with ahci --with dm_mod --with dm_multipath --with dm_snapshot --with dm_zero --with dm_mirror --with pcspkr --with mii --with 8139too --with 8139cp --with i2c_piix4

Hi I have a Dell PE2300 with a Digium TDM400P line card in it (with one module to handle an inbound phone line). This is running on a Fedora 8 system with Asterisk 1.4.21.2-1.fc8 This system has been working nicely for about 12 months. After a recent move of office and relocation of the server Asterisk is back on line, but the TDM line card has stopped working. I have spent half a day

Hello all. I have been running running centos 4.5 final for some time with any problems. Been running great, until today. System was frozen and /var/log/messages showed: Aug 15 23:01:28 mydomain kernel: Unable to handle kernel NULL pointer dereference at virtual address 00000000 Aug 15 23:01:28 mydomain kernel: printing eip: Aug 15 23:01:28 mydomain kernel: c01b2de4 Aug 15 23:01:28 mydomain

Ok! I got it about how many disks I can lose and so on. But regard the arbiter isse, I always set this parameters in the gluster volume, in order to avoid split-brain and I might add that work pretty well to me. I already have a Proxmox VE cluster with 2 nodes and about 50 vms, running different Linux distro - and Windows as well - with Cpanel and other stuff, in production. Anyway here the

Dear list, we have a relatively new Sun Storage 7310, where we connect CentOS 5.5 Servers (IBM LS21/LS41 Blades) via Brocade Switches, 4GBit FC. The Blades boot from SAN via qla2xxx, and have no harddisks at all. We want them to use multipathing from the very beginning, so /boot and / are already seen by multipathd. Problem is, that the Sun 7310 has two storage heads which run in

Hello, this is my scenario: 1)I've created a Pacemaker cluster with the following ocfs package on opensuse 11.3 64bit ocfs2console-1.8.0-2.1.x86_64 ocfs2-tools-o2cb-1.8.0-2.1.x86_64 ocfs2-tools-1.8.0-2.1.x86_64 2)I've configured the cluster as usual : <resources> <clone id="dlm-clone"> <meta_attributes id="dlm-clone-meta_attributes">

Hi. I'm having problems with chan_mISDN configuration. Line "echotraining=yes" causes warning, when Asterisk is parsing misdn.conf and I'm confused why the PBX doesn't accept the setting. No matter which section I try to offer it, it is always invalid or out of range. The setting itself is supposed to be valid, it is in the sample configuration file of chan_mISDN 0.3.1.

Hello, I have a CentOS 7.3 + updates server where my configuration arises from the need to connect via iSCSI to a Dell PS Series storage array and Dell not supporting bonding. So that I need to use 2 nics on the same vlan to connect to iSCSI portal IP and then use multipath. Also, the iSCSI lan is on a dedicated vlan I have only these 2 x 10Gbit adapters and I also need to put other vlans on them

I have not installed the madwifi specific kernel stuff (kdml and hal-kdml) from atrpms. I have installed with wpa rpms. And my Atheros card is working with almost no work on my part (other than runing wpa_supplicant as a deamon). Nice!

Hi, everybody! My pxelinux.0/default file is: LABEL linux KERNEL vmlinuz-2.6.16 APPEND initrd=initrd-2.6.16.img root=192.168.4.110:/clients/192.168.4.100/root When mounting I get: switchroot: mount failed: 22 Kernel panic - not syncing: Attempted tp kill init! Before it I get some messages about: Can't find /dev/console. /clients/192.168.4.100/root/dev was empty. I've copied my

On Fri, 2013-06-28 at 12:17 +0800, Joe Jin wrote: > Find a similar issue http://www.gossamer-threads.com/lists/xen/devel/265611 > So copied to Xen developer as well. > > On 06/27/13 13:31, Eric Dumazet wrote: > > On Thu, 2013-06-27 at 10:58 +0800, Joe Jin wrote: > >> Hi, > >> > >> When we do fail over test with iscsi + multipath by reset the switches

Dear Xen users! In case you were struggling with recent version of th gplpv drivers, I''ve possibly found an LVM related bug in it, and reported to James Harper. Thats''s the point: I''ve tested the mentioned version of your driver on top of 32bit xen-3.2.1 32bit xen-3.3.0 and 64bit xen xen-3.3.0 hypervisors, dom0 was always an appropriate version of a 32bit PAE kernel,

I have tried sending this before, but it did not appear to get through. Hello, When using gfs2 with quotas on a SAN that is providing storage to two clustered systems running CentOS6.5, one of the systems can crash. This crash appears to be caused when a user tries to add something to a SAN disk when they have exceeded their quota on that disk. Sometimes a stack trace is produced in