similar to: 5.2 driver for Marvell Yukon 88E8042 PCI-E Fast Ethernet controller

Greetings list- I''ve got a server ''in the mail'' and I see now on the specsheet that it has Marvell Yukon 8056 NICs onboard. Since I cannot seem to find a HCL for Centos 5 or RHEL5 to help verify, I''d like to know if it works ''out of the box'' on CentOS 5.x or is there additional work to make it function (properly)? My searching has revealed

I'm new to the lists so sorry about any faux pas I may have made. Also I apologize for the length, but I wanted to be sure I covered most of the details. I'm trying to do a PXE install on an Intel 1435VP2 server machine. The PXE install has worked on all the older machines in the cluster, so I know PXE is working. However, these new Intel server machines only support PXE booting from

Hello, Marvel Yukon Gigabit Ethernet is supported by CentOS ? -- -- Devel in Precio http://www.pas-world.com

He Everyone, We found out that till version 3.02 the Yukon nic is supported after it gives code errors, i'm working a lot with ehtherboot via drbl / clonezilla, and together with Steven Shiau we ask you guys if you can arrange that the Yukon can be supported again. Our thanx in advance. Dave & Steven

Me again. The ASUS P5N32-SLI motherboard in my new machine has dual NICs but CentOS has only detected one of them. I've tried rebooting with the network plugged in only to the second one, but kudzu still doesn't find it. Any suggestions?

I am trying to connect two workstations (CentOS 3&4) directly using a straight through cat 5e cable with a crossover adapter on one of the ends. Both hosts have gigabit-capable ethernet card. According to lspci host 1 has: 03:0e.0 Ethernet controller: Intel Corporation 82545EM Gigabit Ethernet Controller (Copper) (rev 01) and host 2 has: 05:00.0 Ethernet controller: Marvell Technology Group

Is anyone using sk98lin Gigabit Ethernet adapters under CentOS 4.x? The version of the driver that ships with CentOS 4.x kernels was too old to support the onboard NICs on some Intel server boards that we recently got, so we installed a newer driver using DKMS. However, we're having problems finding a stable driver to use: the first version that we tried (7.09) gave a kernel panic when I ran

Hello. I have the same problem as many others, PXELINUX (or rather menu.c32) does not work with Marvell Yukon 88E8055 cards. I have two machines, Fujitsu LIFEBOOK S7110 and P7230 that have the same problem; menu.c32 will not load. The version of Marvell's base code is 1.10.1.3 (20060516), Yukon PXE v5.14.1.3 (20060704), in the machines I have tested. I have tried downgrading the BIOS on the

My dd (sk98lin v7.09) supports 3c940 (Marvel/Syskonnect) which the stock v6.x drivers doesn't . Successfull tested on a Asus A-7N8X Deluxe with Marvell Gigabit Lan the dd is available at http://slackpkg.ath.cx/centos/disk/sk98lin/

Hello all, I've been on a real roller coaster ride getting a large virtual host up and running. One troublesome thing I've discovered (the hard way) is that the drivers for Marvell SAS/SATA chips still have a few problems. After Googling around quite a bit, I see a significant number of others have had similar issues, especially evident in the Ubuntu forums but also for a few

Hi, guys. I''ve been trying to use the pci-phantom command line options to xen so as to work around the hardware issue with the Marvell 88SE91xx SATA controllers in IOMMU ([Intel:] VT-d) mode, but I cannot seem to get my head around it. From having had a glance here: http://xenbits.xen.org/docs/unstable/misc/xen-command-line.html and in particular the syntax described as such:

I have a hardware here with 9 NICs (8 of them on-board) and I want to set up 8 NICs as real network interfaces, one for each xen domain. The 9th NIC should be Domain-0 which is working well. Currently I have only set up one domain which is running in bridged mode at the moment. I am currently trying to set up a second domain which uses eth2 but I didn''t succeed. I want to get the

I am trying to build a file server with 1 x 80 GB main drive and 4 x 500 GB SATA drives in RAID in a Supermicro 3U server. I found out the hard way that Centos 4.2 does not have a driver for the onboard Marvell H2 controller the drives are connected to. Supermicro techs sent me aar81xx.rhel4qu2.i686.img as an img file. I used dd to copy to a floppy and dd confirmed successful write. I booted

on an ASUS P5K-E wifi (wifi disabled in bios) board with: 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8056 PCI-E Gigabit Ethernet Controller (rev 12) centos 5.1 did not configure the device. Anyone else see this or have a solution? Tried forcing sky2 module, but init just says device does not seem to be present even tho lspci shows it on the bus. Is there another kernel

Dear Xen folk, I''m trying to use xen as shipped with debian 7.0. The system has 13 disks over 3 controllers. When I boot normal linux, I get this (condensed output from lshw): product: MV64460/64461/64462 System Controller, Revision B disk:0 disk:1 disk:2 disk:3 disk:4 disk:5 product: 88SE9172 SATA 6Gb/s Controller disk:0 disk:1

Hi All, I have bfu''ed to net-virt_xb-21_snv_81_021308. The dladm command on my machine does not have create-etherstub option. Please let me know what could be the issue. Thanks Khushal

Hi, Yesterday i tried to install centOS 8 on my little router and server, but there's no ethernet listed there. I'm using Compaq pressario V3737TU which come with Marvell PCI-e ethernet 100Mbps. It's an old laptop. Could anyone here help?

Hi, I noticed that one of out "Centos 5" servers with an onboard "Marvell 88E8001" was showing some packet overruns. # ifconfig -a eth0 | grep "RX p" RX packets:1629537 errors:0 dropped:0 overruns:3694 frame:0 So I thought about using a driver from "elrepo" the lspci id's suggest to install the "kmod-sk98lin" driver. I yum installed

Hi all, i have a question. I''m going to setup a Xen server for a client. It''s going to serve about 25 clients. It''s a Athlon 64 3200+, which currently runs Debian i386-stable and xen 2.0.7 until Xen 3.0 is stable enough, and then i''m gonna replace it with Debian amd64-stable and Xen 3.0. The Xen dom''s consists of: Samba , file printer sharing most

Hi Everyone, What kind of specific info do i have to give for support for Yukon Nic. ------ Dave Haakenhout wrote: > HPA > What do you want to know exactly hpa? Dave