similar to: rebuilding the kernel.

Good day everyone, Hope someone can help me with a spandsp/app_rxfax problem. I've compiled spandsp 0.0.2pre26, and app_rxfax.c from soft-switch.org Both went just fine, and i've checked my libtiff and libxml (along with the devel-s) versions - they're fine. Machine is fedora core 3, x86_64. Asterisk is 1.2.17, zaptel 1.2.15 Dialing in on a zap channel. T1 PRI, esf,b8zs TE110P

Hello, Is anyone successfully using spandsp 0.0.2pre25 with either asterisk 1.0.x or 1.2.4? I've built a Gentoo ebuild for this version of spandsp and app_rtxfax, and it builds, but I'm not having any luck getting it working. 99% of my test faxes fail. Reverting to 0.0.2pre20 yields a much higher success rate. I've bumped the console debugging level in logger.conf to include debug

I receive this error on the asterisk console and it is pretty much ALWAYS coming up. Sometimes there will be a break where it does not display. We had our PRI provider test the lines and they claim that there is no signalling problem. It doesn't matter if there are no calls or if there are 10 calls in progress the error is still displayed. I also get an annoying popping or clicking sound

Hello list, We're currently facing some issues concerning T.38 gateway faxing. This is a device used almost exclusively for receiving faxes. Calls are incoming to asterisk on a SIP trunk (sangoma netborder) using G711A. Gateway mode is activated in the asterisk dialplan towards a Cisco SPA 112 running firmware 1.3.5. We are using asterisk 1.8.13.0 with the T.38 gateway patch applied (I know I

Hi fellow asterisk users, I am running Asterisk 1.4.29 with an Digium TE121 card (wcte12xp kernel module) an approx. 100 snom320. The whole installation is running without issues since 5 months. Without having changed anything on the asterisk server for at least 2 months, i noticed "clicking sounds" at external calls over the PRI. Asterisk constantly throws the following messages: ...

Hi all, Last night I went to replace an Asterisk 1.4 + mISDN + b410p box with Asterisk 1.6.2 and DAHDI BRI - to no avail. I had two servers so copied network setting etc from the working one, moved the card across, ran dahdi_genconf etc and it didn't work. Here's the console output with notices disabled: lucas*CLI> pri intense debug span 1 Enabled debugging on span 1 [Dec 16

Hi, I am getting this message on the * console on my first pri span. Pri show span show it is down, and I can't make any calls from the span. Apr 27 07:40:23 NOTICE[23988]: chan_zap.c:8202 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Apr 27 07:40:23 NOTICE[23988]: chan_zap.c:8202 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Apr 27

Hi all, as good? I am trying to go up a board TE110P with link E1 ISDN PRI to establish connection with a central office Siemens HiPath 4000. But I am having the following errors: Server1:~ # asterisk -r Asterisk 1.2.10, Copyright (C) 1999 - 2006 Digium, Inc. and others. Created by Mark Spencer <markster@digium.com> Asterisk comes with ABSOLUTELY NO WARRANTY; type 'show warranty'

Hi, we are trying to install Junghann's quadBRI into Dell PowerEdge 2800 system without success. I don't know if the issue can be that Junghann's card fits 32-bit slot and Dell PE 2800 has only 3 PCI-X 64-bit slots. Can this be an issue? We get "CRC errors for HDLC frame" when the card is initialized. Any idea what can be wrong? 1/ We use latest bristuff packages. 2/

All, I am trying to configure hdlc support on T100P Digium card - everything seems ok... but it just does not work at all. I was able to compile all drivers, the light on the card becomes green when I plug T1 link.... but I even can't ping default router IP... there is no data coming back to me, so I am confused completely now. Also I tried both protocols - raw hdlc and cisco hdlc. The

Hello, I contacted Krzysztof Halasa, the maintainer of the current sethdlc code. This is the response he gave me. Of course, I have this working now. Still some minor configuration to do, but It does work, and the connections to the internet are _much_ faster than when I went through the adtran... I would highly recommend to anyone with a fractionated T1, with data and voice channels to

Hi All I have a Junghanns BRI 4 port installed where only the first channel of each line is working i.e. channels 1 and 4 work but 2 and 5 don't. Our config is the same on this box as 15 other similar installations where all works well. the only error I see is in /var/log/messages: Jun 28 15:49:31 pbxct kernel: qozap: CRC error for HDLC frame on card 1 (cardID 0) S/T port 2 Jun 28 15:51:27

Hi There. I have the following setup : Asterisk 1.2.4 , freePBX 2.0.1, spandsp-0.0.2pre24 My problem is as follows : If I set up a very simple extensions.conf. when I dial from a fax machine, it seems as if no fax is being recognised. If I answer the call, I can hear the fax machine beeping. extensions.conf :

I have a pair of sites tied together with a T1 line running zaptel PPP on either end. The system works, but I keep getting these messages in the kernel logs, and users are reporting connection problems (TCP timeouts, and hangs) especially under high usage. --snip-- HDLC Receiver overrun on channel WCT1/0/1 (master=WCT1/0/1) HDLC Receiver overrun on channel WCT1/0/1 (master=WCT1/0/1) HDLC

---------- Forwarded message ---------- From: Jan Prunk <janprunk at gmail.com> Date: Sep 13, 2007 3:35 PM Subject: Bad FCS error To: asterisk-users at lists.digium.com Hello ! I am getting the following error in asterisk logs: Sep 11 17:33:30 NOTICE[2187] chan_zap.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1 Sep 11 21:45:08 NOTICE[2187] chan_zap.c: PRI got event:

Hi Last friday I have upgraded to Asterisk 1.2.7.1 (bristuff-0.3.0-PRE-1p.tar.gz). Since that I have a problem with my Asterisk box. I am receiving these messages: May 24 09:30:11 asterisk kernel: zaphfc: empty HDLC frame or bad CRC received (framelen = 6, stat = 0xff, card = 2). May 24 09:30:12 asterisk kernel: zaphfc: empty HDLC frame or bad CRC received (framelen = 6, stat = 0xff, card = 2).

Hi!, this issue makes me crazy. I read a lot of docs, also * mailling list and I try a lot of things without success. Any help will be appreciated. Here is the info: Hardware: -------------------------------------------- Supermicro Server with motherboard X7DB8, chipset Intel 5000P, Xeon 5050 Digium TE110P Software --------------------------------------------- Asterisk version 1.2.12.1

I've read as much as I can on this error and still can't seem to figure out what's causing this error: Jun 23 20:54:58 NOTICE[7483]: chan_zap.c:7395 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Jun 23 20:55:03 NOTICE[7483]: chan_zap.c:7395 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Jun 23 20:55:03 NOTICE[7483]:

Hi, I'm trying to connect quadbri between powered ISDN phone and ISDN line: ISDN <---1---> TE - * - NT <--2--> Phone I use quadbri, suse 9.2 and latest 0.2.0-RC7k bristuff. I've used sample settings provided with package, but do get strange error (I think that I have wrong setting for P2P or P2MP setting and cables 1 and 2). If I connect phone to ISDN with straight cable

Hi everyone, I have been having some problems lately with our PRI and Asterisk, or maybe it is just me. It happens once maybe twice a day, but when some of our customers are calling in, the phone just drops on them. I pulled the information below from the log from one that happened. I notice why it is happening, but I can't seem to figure out a way to stop it from happening. I also