similar to: CPU temperature in an PowerEdge 860, LM85 chip

Hi! My son successfully played demo of the Bus Driver game and thus asked me to buy him the full version, which I did. Version 1.5 of the game was then downloaded, which is not referenced in AppDb yet, and AppDb entry itself seems outdated. The game cannot complete the registration process, it ask us to connect the machine to the internet, and when we answer, that it's connected, it just

Tyan has posted a lm_sensors config file for the Thunder K8SE S2892 at ftp://ftp.tyan.com/software/lms/lms_s2892.conf However when I ran the sensors command on my S2892 I was getting a readout for an adt7463 chip that wasn't referenced in the config file. I emailed Raphael Deng at Tyan asking him to confirm the manual edit needed to get sensors.conf to refer to the adt7463 chip. His

Hello, I'm having problems with lm_sensors on the motherboard Supermicro X6DH8-G2+ sensors-detect gives me the output attached in the textfile sensors-detect-output.txt As soon as I execute the recommended 'modprobe smbus-arp' I receive the following message: FATAL: Module smbus_arp not found. When I execute sensors, I receive the following:

Hi, A couple of our important servers, both running FC4 but one i386 and one x86_64, have been crashing recently. They both are running ext3 data=journal with large external journals and high commit intervals. Both machines use the gdth driver for their hardware RAID sets, if that's of any use. I think the hardware is good in both cases. I hope someone finds this data useful enough to be

I believe that ch7006 is the only external encoder that's supposed to work, so you're in luck. It sounds like it passes the nv04_tv_identify stage of nv04_tv_create -- perhaps it fails later? Although based on the prints, it's even doing dpms stuff (but it hits _detect a second time... odd). Try booting with nouveau.debug=debug drm.debug=0xe That should provide a bunch more output as

I have a Dell Inspiron 8100 laptop (or I8K) with a NVidia Geforce2 Go (or NV11) with an embedded CH7007A chip, and am seeing the following after getting ch7006 kernel driver/module loaded: # dmesg |grep ch7006 -i --- Snip --- [ 21.191147] nouveau [ I2C][0000:01:00.0] detected TV encoder: ch7006 [ 21.404731] ch7006 1-0075: ch7006_probe: [ 21.411672] ch7006 1-0075: Detected version

Hi guys and gals, I'm working on improving nouveau's support for MXM (Mobile PCI Express Module) chips and need some more data to check my implementation. To see if you can help, the first thing to do is jump over to /sys/firmware/acpi/tables and run "grep MXMS *". [root at nisroch tables]# grep MXMS * Binary file DSDT matches [root at nisroch tables]# If this isn't

fallthrough to a separate case/default label break; isn't very readable. Convert pseudo-keyword fallthrough; statements to a simple break; when the next label is case or default and the only statement in the next label block is break; Found using: $ grep-2.5.4 -rP --include=*.[ch] -n "fallthrough;(\s*(case\s+\w+|default)\s*:\s*){1,7}break;" * Miscellanea: o Move or coalesce a

On Wed, Apr 2, 2014 at 5:24 PM, Roger <rogerx.oss at gmail.com> wrote: > After analyzing verbose nouveau & drm dmesg, I have found seemingly no more > useful details pertaining to having no TV-1 device. The TV-1 device might be > getting lost within DRM, by setting the TV-1 (SVIDEO, Composite) device into > DPMS mode or Full Power Down mode, and the ch7006 datasheet does say

I have a user who wants to have 4 monitors attached to his CentOS 6.4 system. I know that you can't use both on-board video and a PCI video card at the same time, but what about two PCI video cards? The system seems to recognize them as shown by the lspci -v output below, but I can't get Xorg to use the second card. Has anyone done this? If so, what is the trick to get it to work?

Hi, I just want to know if somebody use 2.6.31.4 xenified kernel (aka OpenSUSE) in production? We have been testing it on new Nehalem Xeon server for few weeks w/o any problem. But as soon we tried it on production machine - after several production domUs started - hard OS failure. We had to switch back to 2.6.18.8 - xen stock kernel. Peter _______________________________________________

Hello, I have an issue with my XEN system. I suspect that it might be a bug, but I''m no linux expert, so I don''t know. Here is my problem: I have an ASUS P7P55D-E Premium motherboard, and a Western Digital Caviar Black SATA-III 1TB hdd. I am trying to use AHCI. The dom0 is an Arch Linux. The dom0 boots fine until Intel VT-d is enabled in the BIOS. When I enable it Arch

Hi Ben, I was looking into some of the LUT-related modesetting issues. I've noticed the following... after I load nouveau, one of my secondary GPUs shows this on first modeset (with drm.debug=4): [ 2368.081307] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:44:DVI-I-1] [ 2368.113148] [drm:drm_add_display_info [drm]] non_desktop set to 0 [ 2368.113183]

Giuseppe, One more question about your driver: should we put a recommendation for the "port" name in the man page? Looking at the code, it seems like it should be "/dev/i2c-0" or similar. Thanks, -- Charles Lepple clepple at gmail

https://bugzilla.mindrot.org/show_bug.cgi?id=860 Kevin Brott <kevin.brott at gmail.com> changed: What |Removed |Added ---------------------------------------------------------------------------- See Also| |https://bugzilla.mindrot.or | |g/show_bug.cgi?id=2404 -- You are

https://bugzilla.mindrot.org/show_bug.cgi?id=860 Kevin Brott <kevin.brott at gmail.com> changed: What |Removed |Added ---------------------------------------------------------------------------- See Also|https://bugzilla.mindrot.or | |g/show_bug.cgi?id=2404 | -- You are receiving this mail because: You are the assignee

Hi All, I'm having some troubles with my Dell 860 and TE110P card. Using Asterisk 1.2.14, Zaptel 1.2.12 and Libpri 1.2.4. I'm getting digital noise, like a half ring almost and other jitter. Here's the kicker it's only on the outside part of the call. Ie. if I rang you, you would here it but I don't and the opposite if you rang me you would hear it but I wouldn't. I have

Hi, Is this server silent enough to be installed beside users in office environment ? http://www.dell.com/content/products/productdetails.aspx/pedge_860?c=us&cs=04&l=en&s=bsd Regards -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070316/e657ef4d/attachment.htm

Hello everyone, I'm considering getting me a quad-core Dell PowerEdge 860 to run Asterisk. Anyone else using this model? Any tales of woe and sorrow I should know about? Then, in a couple of weeks, I'm thinking of getting a Sangoma A108 and giving that a try. Same question with that one - any quirks I should be aware of? Girts -------------- next part -------------- An HTML

R 1.2.2, Solaris and Linux: f <- function(x, ...) { g <- function(x, ...) x rbind(numeric(), g(x, ...)) } > f(1:3) Error in rbind(numeric(), g(x, ...)) : ... used in an incorrect context S-PLUS 3.4 gives [,1] [,2] [,3] [1,] 1 2 3 as I would expect. f <- function(x, ...) { g <- function(x, ...) x tmp <- g(x, ...) rbind(numeric(), tmp) } >