similar to: ups nut-2.4.x bug. driver megatec forceshutdown may dont work.

2010/3/14 IT Department ULQS <it at quality.ua>: > > I try send this email to 'carlos.efr at mail.telepac.pt' but: > Fri 2010-03-12 19:26:13: <-- 550-The account has been suspended > Fri 2010-03-12 19:26:13: <-- 550 A conta do destinatario encontra-se > suspensa (#5.1.1) right, Carlos is retired from the NUT team. moreover the megatec and megatec_usb driver are

Hi, I've being using nut 2.2.2 (Debian Lenny) via megatec_usb driver for IPPON Back UPS 600. Then I upgraded to nut 2.4.3 (Debian Squeeze) with broken megatec_usb. I moved to blazer_usb, it connected IPPON. [myups] driver = blazer_usb port = /dev/usb/hiddev0 desc = "Local UPS" #from megatec.c: batteries[] = {{ 12.0, 9.0, 16.0, 9.7, 13.7, 0.0 },

Hi, a few days ago, I bought some of those Mustek UPSes that have both a serial and a USB connector. Currently only the serial port is supported by the megatec driver. This works fine so far. Now I have seen there is a megatec_usb driver, which currently only supports 2 other UPSes. How can I help to find out whether the PowerMust might actually work with the megatec_usb driver? -- Regards,

Hi, I am not sure if you are the list to hit with this, but NUT's megatec driver support ours "Numeric Digital 3000 sw" UPS - at least that's what it claims on front- at the Watcher telescope at Boyden Observatory / RSA. I wasn't able to find manufacturer, but it looks Numeric is some existing UPS factory. I did not receive any informations from manufacturer, so I believ

The REDi Blazer 600VA (BLAZER600c) UPS found here [ro_RO]: http://www.emag.ro/ups-redi-blazer-600va-blazer600c/pd/EX5X2BBBM/ which is actually a Centralion Blazer 600VA [en_TW]: http://www.centralion.com/html/product/back-Product-ups-blazer400.htm works with the blazer_ser driver ----------shell output---------- # upsrw ups # upscmd -l ups Instant commands supported on UPS [ups]: beeper.toggle -

Hello, i've a problem, this is my configuration: - Atlantis Land UPS with serial port - a generic RS232 to USB cable adapter (QinHeng Electronics HL-340 USB-Serial adapter for linux). The problem is in the syslog file where i find: [...] Aug 19 09:07:25 ProLiant megatec[1126]: Communications with UPS lost: No status from UPS. Aug 19 09:07:26 ProLiant megatec[1126]: Communications with UPS

On 1/23/07, Henning Brauer <hb-nut@bsws.de> wrote: > good new first: the megatec driverin 2.0.5 now works with the Online > Xanto S3000R here - well, for the very basics. > > the UPS has NO way ofidentifying itself. It also does not respond to > the power ratings query ("F"). I previously used a hacked up fentonups > driver. This means the driver cannot figure out

I had some free time this weekend, and made some long overdue changes to "megatec". The thing is, these changes lead to a couple of questions that I must ask before I go on and "svn commit" them: 1) The blazer, fentonups, esupssmart, ippon, sms and mustek drivers are now completely covered and all of their functionality should now be present in megatec, and also every model

I'm running NUT 2.6.3 on Debian wheezy [ with a 3.3.0 i686 kernel ] I've installed NUT via Debian APT [ package nut version 2.6.3-1 ] I have a REDi Blazer 600VA (BLAZER600c) UPS and I want to detect power failures. I have tried the following drivers: * gamatronic: Can't talk to UPS on port /dev/ttyS1! * bestups: Unable to detect a Best/SOLA or Phoenix protocol UPS * blazer_ser: No

In my opinion, there might be just one problem: the blzr driver doesn't provide anymore two splitted drivers (serial and usb), so this isn't going to be a 'silent update' for those using these drivers (should we provide symlinks or the like?). If this doesn't sound like a problem to you, I'll take care of the rename. Plus, if you could take a look to the blazer-fix pull

Hi! This is the weirdest problem I have found for a long time! Using nut-2.0.5 and a Gentoo powered HP Proliant ML350 I setup the config files just the same as I always do and tried to get the megatec driver chatting to the UPS. It worked fine on a Windoze server with Upsilon2000 so I have a bit of confidence in cable etc! When I ran upsc after starting upsd to complained about stale data! Most

Hello list, we've got a PowerWalker VI 1000E/RT LCD UPS and like to use it with NUT using the blazer_ser driver. For the blazer_ser driver to display percentage, one has to add battery.voltage.high and battery.voltage.low voltages to the ups config. Here's what I received from the powerwalker customer service: Battery-Low Voltage: 21.6VDC Battery Shutdown: 19.2VDC Now my questions: 1.

Hi, thanks for the reply. On 2014-05-29 05:21, Charles Lepple wrote: >> Now my questions: >> 1. should the blazer_ser's high voltage be the voltage during charging >> or right after I've unplugged it from the mains? > sounds like during charging (or more accurately, during float charging at the end of the cycle): > >

Hi, I would like to report that Tuncmatik Newtech Pro 1 KVA (http://www.tuncmatik.com/en-US/productDetail.asp?RecID=290) works with nut(2.4.1) blazer_usb, blazer_ser and megatec drivers. The UPS came with an usb cable and a java based software for both linux and windows, named ViewPower (http://www-power-software-download.com). This UPS has double interface a USB interface and a serial

Hello, today I'm fighting with a Online Zinto 1000 (lsusb.txt) produced by Phoenixtec/Eaton ;-) http://www.eaton.com/EatonCom/OurCompany/NewsandEvents/NewsList/CT_141334 I have tested different drivers without success (please see attachments usbhid-ups.txt, bcmxcp_usb.txt, blazer_usb.txt) The help got unfortunately time outs (explore.txt)

Hello, the code below the failing part mentions this flavor of protocol, drivers/blazer_ser.c:463 /* * If a command is invalid, it will be echoed back. * As an exception, Best UPS units will report "ACK" in case of success! */ I prepared a patch, it adds a similar check and also checks (in both occurencies) for blazer_command()<0, the latter

Hi Mutlu, 2009/8/7 Mutlu T. <cmtunc at gmail.com> > Redirecting to debian.org domain due to being rejected as spam by free.fr > > > ------- Forwarded message ------- > From: "Mutlu T." <cmtunc at gmail.com> > To: arnaud.quette at free.fr > Cc: > Subject: New NUT HCL entry / (brand)Inform (series)Informer Compact > Date: Fri, 07 Aug 2009 15:31:04

On Aug 11, 2013, at 2:12 PM, ????????? ???????? wrote: > I see no problem with how the device communicates the Blazer/Megatec protocol. > I must have found a bug in the driver. It is possible that the shutdown was tested with a different implementation of the protocol. What do you get from the "I" command? On Aug 11, 2013, at 11:25 AM, ????????? ???????? wrote: > So I

Daniele, Thanks again for your work on both the voltronic and blzr drivers. To get the most exposure to new drivers, what we have typically done in the past is to rename the existing driver as *-old, so that users get the new driver by default when they upgrade (but the old driver is still available if there are regressions). This is how we are incorporating Michal's apcsmart updates. On

Hi, I am trying to setup a CentOS staging server as part of my development/testing setup. CentOS is working fine and I'm able to connect via SSH and HTTP without isssue. I want directly edit code on the CentOS server from my main tower running Windows 7 Ultimate 64bit but I'm struggling to authenticate a connection. I'm at a point where Windows knows there is a share available but