similar to: megatec_usb.c modification for UPSONIC PROFFICE 650 USB

Hi, I recently installed a Upsonic PrOffice 650 UPS, which is a cheap model[1] available in Australia. It has a serial and USB port, and comes with a note saying WinPower software can be downloaded from [2]. Investigation of the software shows it to be Java with native libraries for serial and USB. Disassembling various classes reveals it talks at 2400 baud, and has a protocol similar to

Greetings Gentlemen, I have Mustek NetGuard 1000 UPS which is equivalent to Ippon SmartWinner 1000. I have tried to run several latest builds of NUT, but run megatec_usb driver still failed with my device. I hope the information below might help. Regards, Oleg Here is the information which may help: lsusb -v Bus 002 Device 002: ID 06da:0003 Phoenixtec Power Co., Ltd Device Descriptor:

Hi all, I've bought myself a Upsonic Power Proffice 650 (Pro Office on the compliance sticker :-/) and can't work our which nut ups driver it requires. Product Brouchure: http://upsonic.com.au/pdf/proffice.pdf George

I am working with a number of our customers to ensure that NUT works with different UPS's on Freebsd 9.1. The current one I am looking is support for: *Upsonic Commercial UPS CXR 2000 - 2000VA/1200W - Rack/Tower* What seems to be supported in Freebsd is: CXR1000 blazer_ser LAN Saver 600 genericups upstype=0 Power Guardian genericups upstype=7 PrOffice 650 USB blazer_usb DS-800 USB

On Jan 31, 2014, at 3:14 PM, Chris Duffy wrote: > The current one I am looking is support for: > > Upsonic Commercial UPS CXR 2000 - 2000VA/1200W - Rack/Tower > > What seems to be supported in Freebsd is: Small clarification: the hardware compatibility list isn't broken down by operating system (theoretically, the drivers should work on any POSIX system, with additional

Thx for the info Charles. Here is what I am seeing from 'usbconfig list' ugen0.1: <EHCI root HUB Intel> at usbus0, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE ugen1.1: <EHCI root HUB Intel> at usbus1, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE ugen0.2: <product 0x0024 vendor 0x8087> at usbus0, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE ugen1.2: <product 0x0024 vendor

Hello. I've been experimenting with the USB connection of an Ippon BackComfoPro 800. This is the device "06da:0003 Phoenixtec Power Co., Ltd". The current SVN version of NUT does not work with this device. The megatec_usb driver can't get a proper reply to a Q1 request, failing with an error message about "short read (14 bytes)" instead. I have found the reason for

On Feb 3, 2014, at 9:05 PM, Chris Duffy wrote: > Thx for the info Charles. > > Here is what I am seeing from > 'usbconfig list' [...] > ugen1.3: <USB UPS PPC> at usbus1, cfg=0 md=HOST spd=LOW (1.5Mbps) pwr=ON > > > The last line I guess is key. Unfortunately, it is not very unique: the vendor can pick the string "USB UPS PPC", but the drivers

Charles, Here is the output: ugen1.3: <USB UPS PPC> at usbus1, cfg=0 md=HOST spd=LOW (1.5Mbps) pwr=ON bLength = 0x0012 bDescriptorType = 0x0001 bcdUSB = 0x0200 bDeviceClass = 0x0000 bDeviceSubClass = 0x0000 bDeviceProtocol = 0x0000 bMaxPacketSize0 = 0x0008 idVendor = 0x06da idProduct = 0x0005 bcdDevice = 0x0003 iManufacturer = 0x0003 <PPC>

Hi all! Maybe possible adds something in megatec_usb driver for normal working with ippon 2000? This is output for drivers megatec_usb and blazer_usb: =========================================================== gate# /usr/local/libexec/nut/megatec_usb -DDDD -a IPPON Network UPS Tools - Megatec protocol driver 1.6 (2.4.1) Serial-over-USB transport layer 0.10 debug level is '4' Checking

Hi Bj?rn, 2009/10/9 Bj?rn Torkelsson > Public bug reported: > > Binary package hint: nut > > I have recently upgraded from hardy to intrepid to jaunty. After > upgrading to Intrepid the megatec_usb stopped recognizing my Trust PW- > 4130M ups, it still does not work on Jaunty. It worked without any > problems in hardy. > > I tried the megatec_usb driver from hardy

Hi. My Belkin UPS F6C1100-UNV works fine with megatec_usb version 1.6 (2.4.1). However, it doesn't work with 2.4.2 nor 2.4.3. # /lib/nut/megatec_usb_old -D -a belkin Network UPS Tools - Megatec protocol driver 1.6 (2.4.1) Serial-over-USB transport layer 0.10 debug level is '1' Starting UPS detection process... 0 out of 5 detection attempts failed (minimum failures: 2). Cancelling

Hi, I'm not the maintainter for the "megatec_usb" driver (in fact, I'm no longer maintainer for the base "megatec" either), so I don't really know the status for that particular UPS. I'm forwarding this to the NUT mailing-list though. Regards, -- Carlos Rodrigues On Fri, Dec 5, 2008 at 10:30 AM, Adrian Czerniak <adrian.czerniak at becomo.com> wrote:

Hi, I'm not the maintainter for the "megatec_usb" driver (in fact, I'm no longer maintainer for the base "megatec" either), so I don't really know the status for that particular UPS. I'm forwarding this to the NUT mailing-list though. Regards, -- Carlos Rodrigues On Fri, Dec 5, 2008 at 10:30 AM, Adrian Czerniak <adrian.czerniak at becomo.com> wrote:

Hi Alexey, Please post the output of 'lsusb' and 'megatec_usb -a sven_625 -u nut -DDDDD'. On Monday 15 June 2009 14:32:16 you wrote: > Package: nut > Version: 2.4.1-3 > Severity: normal > > I have a SVEN Pro+ 625 ups that uses megatec_usb driver. > In ups.conf I describe it like: > [sven_625] > driver = megatec_usb > port = auto > desc =

Hi, i recently bought an UPS from Integra Tech (http://www.integra-ups.com/eu/es/main.htm), the ePlus 450-850va model (http://www.integra-ups.com/eu/es/eplus1.htm), sorry i didn't find it in english, and i'd like to know if there will be support on this brand and model. When i reconnect it, i get this: [739610.568073] usb 1-1: USB disconnect, address 2

Hello all! Some days ago we received new UPS?Powercom BNT-2000AP with USB interface to replace an old staff and I've spent four last days trying to connect it with NUT. I have a FreeBSD 8.4 box with NUT 2.7.2. # dmesg|grep -i powercom ugen0.3: <POWERCOM Co.,LTD> at usbus0 uhid0: <POWERCOM Co.,LTD HID UPS Battery, class 0/0, rev 1.10/0.01, addr 3> on usbus0 uhid0: <POWERCOM

-----Original Message----- >From: Charles Lepple [mailto:clepple at gmail.com] >Sent: Thursday, 13 November 2014 12:12 AM > >I am surprised that the blazer_usb configuration didn't work. If you leave off >the matching options, does this find the UPS? > >[upsonicRT1000] > driver=blazer_usb ## or nutdrv_qx > port=auto > desc="UPSonic RT1000"

On Nov 12, 2014, at 2:49 AM, Klint Gore <kgore4 at une.edu.au> wrote: > Can someone give me a push in the right direction with this? I?m trying to get an upsonic IRT1000 to work on ubuntu 14.04lts using the usb connection. The most likely drivers (blazer_usb and usbhid-ups) don?t seem to recognize it or I?ve got the configuration parameters wrong. I?ve got no idea what driver it

Hi, Has anyone had success with the Dynamix 650VA, that uses the USB cable? I can't get megatec_usb to recognize it, I have tried both stable and development versions. Regards Glen Ogilvie