similar to: New Mustek UPS model working

Arnaud Quette wrote: > Anyhow, I would more see this as a merge of all these drivers, with > some autodetection or flag/param to switch the mfr/model and maybe > capabilities... Whatever the driver name is, a good thing would be the > name of the protocol or something generic enough, though powermust is > fine. Ok, I made some minor changes to powermust, to make it less

Disclaimer: I've setup APC UPS monitoring and it works... ... but when it comes to mustek powermust 600usb (connected via com-port), I can't make it work. Got NUT installed via aptitude in ubuntu feisty and a basic setup, exactly the same as for the apc, except for the name of the ups and the corresponding section of ups.conf -- [mustek] driver = megatec port = /dev/ttyS1

Hi, I'm having a hard time configuring a Mustek Powermust 600VA ups to work via USB with nut. I read somewhere that nut works OK via the rs232 cable, but unfortunately I don't have a COM port in my computer. The kernel detects the ups as an Xbox pad :) and loads the xpad module. I tried running /lib/nut/megatec with different /dev/ttySx but it displays megatec protocol UPS was not

Hi all, I'm thinking buying a UPS Mustek PowerMust 600 USB to shutdown a Linux box on case of power failure. Can I use nut with this UPS without problems? I checked the page http://www.vamos-wentworth.org/upsinfo.html and was only something (incomplete) about Powermust 400 (information from November 2005). Could this be already changed? Thanks in advance.

Hi, a few days ago, I bought some of those Mustek UPSes that have both a serial and a USB connector. Currently only the serial port is supported by the megatec driver. This works fine so far. Now I have seen there is a megatec_usb driver, which currently only supports 2 other UPSes. How can I help to find out whether the PowerMust might actually work with the megatec_usb driver? -- Regards,

Hello, We are using the equipment "MUSTEK PowerMust 3000 NetGuard RM". That is using Megatec protocol. But unfortunately not all the data can be viewed correctly when dumping from utility "upsc". For example: upsbox# upsc mustek at localhost battery.voltage: 108.00 battery.voltage.nominal: 96.0 driver.name: megatec driver.parameter.pollinterval: 2 driver.parameter.port:

Hi all, Currently, the "megatec" driver only supports UPSes which have a serial (RS232) interface. However, I'm under the impression that most of the models that speak the megatec protocol, and have an USB interface, just have a standard serial-to-USB converter inside. This being the case, there should be a "/dev/ttyUSBx" device which the megatec driver could use just as

Hi all, Currently, the "megatec" driver only supports UPSes which have a serial (RS232) interface. However, I'm under the impression that most of the models that speak the megatec protocol, and have an USB interface, just have a standard serial-to-USB converter inside. This being the case, there should be a "/dev/ttyUSBx" device which the megatec driver could use just as

"mustek" is all but deprecated, so the effort should be to get powermust/megatec working. Since you have the latest development code installed, can you please run "/path/to/megatec -DDDD -a the_name_for_your_ups" (this without starting NUT normally - i.e. without upsd, upsmon, etc) and send me the output? The output should help me figure out why you are getting data stale

Hello, fisrt, you should subscribe to the NUT user mailing list to get a good support, since I've personaly no knowledges about such units: http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser Next, you should try the latest nut release (2.0.5 currently, but 2.2.0 soon) and most of all the new megatec driver. 2007/6/10, esva2 at inbox.lv <esva2 at inbox.lv>: > Dear

On Feb 11, 2008 5:30 PM, Marcio Gomes <mpg at microlink.com.br> wrote: > I change the if in [OFF] detect state to, in original way, if you send a > reset.watchdog, the UPS goes > to OFF state in clients, but it is not correct, because UPS is OL and > Shutdown are in progress, but > the power is not OFF First of all, thanks for the patch. But I have a few comments: Are you

Hi folks, has anyone been successful in getting a Mustek PowerMust 500 to talk to nut? All my attempts (tried "mustek" and "powermust" as drivers) have been unsuccessful so far. Thanks for any clues. Sascha -- http://yoyodyne.ath.cx

Hi! I am trying to install subj, on my Bubba miniserver, that runs Debian. I am stoped now with driver test: upsdrvctl start Network UPS Tools - UPS driver controller 2.0.4 Network UPS Tools - Megatec protocol driver 1.4 (2.0.4) Carlos Rodrigues (c) 2003-2006 Unable to open : No such file or directory Things to try: - Check 'port=' in ups.conf - Check owner/permissions of all

Hello ! first off, thank you all for making this piece of software. from what i have seen so far this seems to be a really mature and advanced tool for all sorts of UPS models ! I`d like to tell that I own a UPS which isn`t listed on the compatibility list, but seems to be compatible. It is a PowerWalker - see this at

Hello ! first off, thank you all for making this piece of software. from what i have seen so far this seems to be a really mature and advanced tool for all sorts of UPS models ! I`d like to tell that I own a UPS which isn`t listed on the compatibility list, but seems to be compatible. It is a PowerWalker - see this at

Hi, I'm not the maintainter for the "megatec_usb" driver (in fact, I'm no longer maintainer for the base "megatec" either), so I don't really know the status for that particular UPS. I'm forwarding this to the NUT mailing-list though. Regards, -- Carlos Rodrigues On Fri, Dec 5, 2008 at 10:30 AM, Adrian Czerniak <adrian.czerniak at becomo.com> wrote:

Hi, I'm not the maintainter for the "megatec_usb" driver (in fact, I'm no longer maintainer for the base "megatec" either), so I don't really know the status for that particular UPS. I'm forwarding this to the NUT mailing-list though. Regards, -- Carlos Rodrigues On Fri, Dec 5, 2008 at 10:30 AM, Adrian Czerniak <adrian.czerniak at becomo.com> wrote:

System: Cenots Linux 6.9 Application: nut-2.7.5-0.20170613gitb1314c6 [with usb 0.1 from distro] Device: Mustek PowerMust 1060 LCD Comunication log file: dump.txt We are looking at the possibility of successful communicating with this device UPS Mustek PowerMust 1060 LCD. PS: wolfy on the list gives me assistance and i can install any new compiled nut version from sources. Thanks, Catalin.

On Wed, Feb 11, 2009 at 11:30 AM, Fr3ddie <fr3ddie at fr3ddie.it> wrote: > Charles Lepple wrote: >> When something gets updated, you would then run 'svn update' to pull >> the latest changes in. > > Ok. > >> The dependencies are set up such that if only one driver is changed >> during the SVN update, running 'make' on that directory should

I Carlos I'm troubleshooting this problem with the driver you wrote: My Ups is Powermust 800 The OB-LB status cames too late to shutdown my Suse 10 system, I searched to find out how to change the state to LB when battery is at almost 30%. Only in this way I'll be sure the pc will shutdown correctly Please tell me how to do so Thank You so much I'll be waiting Best Regards