similar to: APC SmartUPS 750 (SUA750) missing ambient data with usbhid-ups

Hi, Can't get newhidups (2.0.5) or usbhid-ups (SVN trunk) to work 2.0.5 hidups seems to work, but I was hoping for more information... like temperature, etc. Tried newhidups and usbhid-ups, but they don't seem to detect my UPS... should I switch back to serial? Will I get more information? (trying not to move back to apcupsd, since i have a mixed environment) Here is some debug

I sent this to the NUT users list and no response so I thought I'd send it here next.. It's a pretty easy issue really: > Hey all, > > I have a measure-UPS card and the external cabled module. > > They're supposed to operate the same... does NUT auto detect them when using the apcsmart driver or are there config parms required? > > The the smart-slot unit is

I'm trying to setup a server controlling 8 ups, 6 APC Smartups 1500 and two 1000. Because of the number of ups, i connected them using usb cables. I'm using Debian Etch AMD64 and nut 2.2.0 from testing (already tried 2.0 from stable, but had problems reading the ups serials and all the following problems of 2.2). This is my ups.conf: [ups2] driver = usbhid-ups port =

Perhaps someone else could confirm this, I have an APC UPS with a built-in network management card with environmental sensor for temp/humidity. The OID index for the sensors appears to be .1 (the last component for each of the OIDs listed below). The original source code has them at .0 drivers/apccmib.h #define APCC_OID_IEM_TEMP ".1.3.6.1.4.1.318.1.1.10.2.3.2.1.4.1" #define

Fellows, I've had this stagging for too long: For some writable (RW) variables, that support ranges of values, ENUM and STRING are too limited and not adapted. So it's worth adding a new RANGE type, with the needed driver function (dstate_addrange()) and server / client support. Thus, I'm intending to do the following network protocol addition: * new RANGE type, for the "GET

We are configuring a server with a Tripplite SmartUPS, Web SNMP Card, and Envirosense Probe. The configuration is good using usbhid driver and we can get it to shutdown clean by producing a "power event" (pull the power cable). It is not very clear how to add or see the values associated with the external probe. We need to be able to shutdown based on the input from the probe as well as

We recently had to replace an old APC SmartUPS 3000 with a newer 3000VA (the 2U one). It has both serial and USB in the back (with an RJ-45 on the end of the serial cable). I can't get the apcsmart driver to connect. I figured it should work the exact same as the old UPS, with /dev/ttyS0 as the port (I'm using the same port on the server that the last one was plugged into). I even

On Tue, 8 Oct 2013, Philip Tait wrote: > Here is the upsc output: > > # /usr/local/ups/bin/snmp-ups -DD -a irs2-ups1 > Network UPS Tools - Generic SNMP UPS driver 0.68 (2.6.5) > 0.000000 debug level is '2' > 0.000327 SNMP UPS driver : entering upsdrv_initups() [snip] > 4.457750 No supported device detected I'm using a APC smart ups with a

Bonjour, Je fais suite au message que vous avez post? en 2015 : http://lists.alioth.debian.org/pipermail/nut-upsuser/2015-February/009568.html J'ai le m?me probl?me et ne trouve pas la solution. Comment vous en ?tes-vous sorti ? D'avance, merci pour votre aide. -- Cordialement Herv? BASTET Nouveau num?ro non surtax? 01 69 42 87 94 Ce message est prot?g? par les r?gles relatives au

OS: CentOS 7 NUT Version: 2.7 Installed NUT through: yum install nut UPS: APC smart UPS srt3000 with NMC I am trying to set up NUT with snmp for my apc ups. Heres the config; [ups6]                 Driver = snmp-ups                 Port: ups6.domain.name (also tried 192.168.24.9)                 Snmp_version = v3                 secLevel = authPriv                 secName = ups6

Hello One our customer has two Linux HP-branded servers powered from "clasic" APC Smart-UPS 2200 RM 2U (p/n SUA2200RMI2U). It is connected to first server via RS232c port with APC-branded cable. We have installed NUT 2.6.4 with apcsmart driver. This setup works fine for months. Two weeks ago all the hardware powered from the UPS started to switch off occasionally while on line

Hej! Hope nut-upsuser is an appropriate place to post additional info about the smartups protocol, please tell me if not. I got an APC Smartups 2200 (5U Rack Mount, European/230V version, 48V batteries) a couple of days ago, was very happy to find the protocol description at http://www.networkupstools.org/protocols/apcsmart.html, and started to play. At the point when everything was working

Hey guys, I built my own 940-0024C cable as described here: http://www.networkupstools.org/cables/940-0024C.jpg My problem is that I can't receive anything. Sending (e.g. through minicom or my own application) works fine. Nut itself is not able to detect My UPS or anything else. <snip> [myups] driver = apcsmart port = /dev/ttyS0 cable = 940?0024C # also tested without cable option

Hi, I have the following system configuration (probably does not matter, but anyway): Ubuntu Linux x86 VM running under ESXi bare metal hypervisor. UPS is connected to the ESXi host, and VM communicates to the UPS using USB pass through option. Details of elaborated shutdown sequence are out of topic, so I skip them. NUT was installed from the package, I believe it is recent enough. NUT was set

I need direction. I don't know what to google for anymore. I am unable to get my SmartUPS 2200XL to be recognized. My suspicions are that it's UDEV or Kernel related. I've updated the kernel to the highest version I feel comfortable with due to other things that run on the server, and I've updated UDEV a bit too. When I plug in the USB cable from the UPS into the server, I

(Note that I mentioned this *was* previously working with an older version of Nut). [irs2-ups1] driver = snmp-ups port = irs2-ups1.sum.naoj.org mibs = auto community = private irs2-ups1.sum.naoj.org responds to pings. On Tue, Oct 8, 2013 at 3:55 PM, Tim Rice <tim at multitalents.net> wrote: > On Tue, 8 Oct 2013, Philip Tait wrote: > > > Here is the upsc

2009/5/3 Thomas Juerges > -----BEGIN PGP SIGNED MESSAGE----- > Hash: SHA1 > > Hi Arnaud, > Hi Thomas, > I just checked the 2.4.1 version of nut and found that you forgot to add > my old UPS model (APC Smart-UPS 900). I guess it is because you were > busy at the time when I sent you the patch. So here it goes again. :) > uh, right sorry. I was pretty sure I applied

Here is the upsc output: # /usr/local/ups/bin/snmp-ups -DD -a irs2-ups1 Network UPS Tools - Generic SNMP UPS driver 0.68 (2.6.5) 0.000000 debug level is '2' 0.000327 SNMP UPS driver : entering upsdrv_initups() 0.000341 SNMP UPS driver : entering nut_snmp_init(snmp-ups) 0.056112 SNMP UPS driver : entering load_mib2nut(auto) 0.056126 trying the new

Here are the results from the output of upsc under different conditions from my Debian Test system with NUT 2.7.2 : Normal: ups.status: OL No wall power: ups.status: OB Runtime calibration (started from AP9630 web interface): ups.status: OB CAL So at this stage there is a difference! I then connected to my QNAP and set the UPS settings on the web interface to "Shutdown server if power

Hello, I can get nut to work with this UPS using the apcsmart driver, but only with limited functionality. It is only reporting the OL/OB status and that's about it. None of the other useful variables such as run time, load etc are reported and initiating battery tests does not work either. Has anyone managed to get nut to report more than these variables with a Matrix type UPS? I see