similar to: Powerware UPS slots ports and protocols information

I'm not sure about one thing: you assign stack slot to each new register you replace the spilled one with. And then you need to allocate physical registers to them. Is it possible to assign physical register to the virtual one which has a stack slot already? On 8/21/06, Fernando Magno Quintao Pereira <fernando at cs.ucla.edu> wrote: > > > > So what addIntervalsToSpills

Someone might want to add this to the docs - cable list and compatibility list - took me way to long to find. I was trying to find information on my UPS and came up with the following names for the same UPS series. Powerware 5119 Exide name was NetUPS SE Deltec name was PowerRite Pro II (1000VA-3000VA) What I have: The Exide NETUPS SE model PRC2400a p/n 05144038-3904 OUTPUT 2400VA 1600 WATTS

Hi, I'm having trouble with nut running on feisty. I have a powerware 5110 connected using USB i did an "sudo lsusb -a" before and after i plugged in the powerware usb cable and did a diff on the results of the two which was: -- 322c322 < Port 2: 0000.0100 power --- > Port 2: 0001.0301 C_CONNECT lowspeed power connect -- current ups.conf is: -- [pw5110] driver =

Is there support for powerware 3110 yet?

Hello, I am attempting to monitor my two Powerware 3110 UPS from Gentoo Linux using nut-2.2.0, kernel-2.6.22.1 via USB. From what I can gather around the net (circa 2005) things with USB on this UPS just didn't work. Has this changed and is there anything I can do to help? My ups.conf contains the following... [ups-router] driver = usbhid-ups port = auto desc =

Hi! I'm using nut to control a ups powerware 9135. All are working, but, in the shutdown, the ups don't poweroff. I did check with upsc, and I can't see a ups.delay.shutdown variable to set the time of automatic poweroff, when I did complete the shutdown of machines. Before, I did use a propietary program to work with this ups, and the daemon did poweroff the ups without problems. But,

(I saw this flipping through the archives for something else.) Marek, did the bcmxcp driver work for you or is your UPS too old? John

Has anyone gotten the newhidups driver to work w/ the Powerware 9120 series? Here's what I get for debug info (It's the Phoenixtec device): $ sudo lsusb Bus 002 Device 002: ID 0846:1040 NetGear, Inc. Bus 002 Device 001: ID 0000:0000 Bus 001 Device 002: ID 06da:0002 Phoenixtec Power Co., Ltd Bus 001 Device 001: ID 0000:0000 $sudo /lib/nut/newhidups -DDDDD auto Network UPS Tools: New

Hello All, Sorry for the long post, I'm just trying to give as much info as I have about the problem(s) ... Recently I've tried to port NUT to the hardware router Asus WL-500g Deluxe (http://wiki.openwrt.org/OpenWrtDocs/Hardware/Asus/WL500GD), that runs OpenWRT Linux distribution (http://www.openwrt.org) based on Linux 2.4.30 kernel, in order to support my Powerware 5110 UPS (through USB

> It is a pleasure for me to help NUT Project and I will order a SNMP Web > card 66102 to following address [ address information removed ] > Is it OK ? (if yes, the order could be issued on next Monday) That would be a great help, I appreciate that. It's just too bad that you CC'ed the NUT development mailinglist with my full (private) address information. I'd rather keep

Hi I have PW 5115 500 UPS which has both RS232 and USB connectors. bcmxcp driver works fine with serial connection but bcmxcp_usb does not with USB one. After some USB sniffing on windows box I've found that PW5115 communicates in other way than supposed in driver. Applying attached patch makes driver to work properly. System: FreeBSD 6.2 but ugen driver needs patching in order to respect

Earlier this year, I added a patch to my local NUT tree to additionally print the value of usb_strerror() if usb_clear_halt() failed. (Ignore the commented-out goto.) Since these messages are at the LOG_ERR level, should we add usb_strerror() to all of the calls in nut_usb.c? diff --git a/drivers/nut_usb.c b/drivers/nut_usb.c index 494a1fa..4ca2691 100644 --- a/drivers/nut_usb.c +++

During the last month, I've been integrating a Powerware 5115 into an embedded system by writing a custom NUT daemon. This work has gone quite well and NUT has been very helpful, but it sure would be nice to have some additional instcmds for the 5115. The bcmxcp driver comments mention "manuals for the BCM/XCP". I'm wondering if I could get a copy of those so that I might

Hello, does NUT support Powerware Prestige EXT 1000VA / PowerWorks A30 models in smart mode? I don't see them mentioned in the compatibility list (only Powerware 3115 and 5119 are there, listed as supported only by the "genericups" driver). Is the protocol known to be compatible with any other, supported UPS types? Thanks, Marek

Help please on Powerware 3105 serial (aka SOLA 305 here in Australia). Is it best configured as a contact-closure device or do I try and persist to get bcmxcp to work - which it won't so far? Running on SUSE 10.1 Thanks,

Hello, I have a Powerware 5125 UPS and I don't know which driver I should use. In the compatibility list for the stable branch I see 2 sections for this model: 5119, 5125 - genericups upstype=15 PW5125 - bcmxcp Why are there 2 and which should I use? Thank you.

Here is my ups.conf... [ups-router] driver = usbhid-ups port = auto desc = "Powerware 3110 - Router" [ups-server] driver = usbhid-ups port = auto desc = "Powerware 3110 - Server" Here is the output from upsdrvctl start... Network UPS Tools - UPS driver controller 2.2.0 Network UPS Tools: 0.28 USB communication driver 0.28 -

Hi, I have an UPS Powerware 5110 ( usb connection ), on Linux OS is Debian 4.0 The /etc/ups.conf file setting is: [myups] driver = bcmxcp_usb port = auto desc = "UPS Powerware 5110 1500 VA" When the daemon starts it displays the following message: "Starting Network UPS Tools: (upsdrvctl failed)." Looking at /var/log/syslog I found the following line

Hi all We're considering getting some Powerware 9355-30-M-0 UPSes to replace some older ones, so I wonder if it would be possible to use NUT for this. It seems 9315 is supported, but AFAICS that's the top model. Thanks roy -- Roy Sigurd Karlsbakk (+47) 97542685 roy at karlsbakk.net http://blogg.karlsbakk.net/ -- I all pedagogikk er det essensielt at pensum presenteres intelligibelt. Det

I'm running Solaris 11 Express (snv_151a X86) with NUT 2.6.0 compliled from the source tarball and a Powerware 5115. I was seeing the driver hang, so gave it some '-D's (23 apparently ;-) and found that it seems to be getting into an infinite loop when reading data from the UPS. The debug output is attached and I would be very grateful for some help or advice on what to try next.