similar to: usbhid-ups driver

Hi, I have a Liebert PowerSure Personal XT that I have connected via its USB interface. lsusb shows that it is there and when I plugged in I got the kernel messages: Jul 3 11:25:37 mint kernel: usb 2-2.2: new low speed USB device using address 4 Jul 3 11:25:38 mint kernel: hiddev96: USB HID v1.11 Device [LIEBERT PowerSure Personal XT] on usb-0000:00:10.0-2.2 The documentation suggests that

Hello everyone, Charles suggested (about a week ago) that I repost to this list. I took a moment to run some additional tests ... The basics: -- UPS: Liebert PowerSure PSA 500 (from the 230 VAC / 50 Hz line) -- Kernel: 2.6.11.5 (from sources), USB support (down to and including CONFIG_USB_HIDDEV) compiled in statically (not as a module) -- Rest of OS: Basically still from the original SuSE

[FAQ on USB-connected UPSes] > Remember: this is brand new *experimental* software and is probably > very broken. Do us a favor and report successes or failures to > the mailing lists. No problem ... : UPS: Liebert PowerSure PSA 500 NUT: Version 2.0.2 Kernel: 2.6.11.5, with CONFIG_USB_HID, CONFIG_USB_HIDINPUT, and CONFIG_USB_HIDDEV compiled in (statically)

Hi, I have a Liebert Powersure Personal XT 700 and have followed the installation instructions from here http://www.networkupstools.org/doc/2.0.0/INSTALL.html. I'm pretty sure I've got the ups.conf, upsd.conf and ups.users correct. I have setup upsmon.conf as suggested in the installtion guide with the exception of FINALDELAY which I set to 0 when I found things weren't working

Hi all, I?ve a UPS Liebert GXT3 500-3000VA with USB port. I?ve install NUT version 2.2.2 from repository packages for Debian Lenny. Linux kernel 2.6.26 I?ve try to use usbhid-ups driver in ups.conf [liebert] driver=usbhid-ups port=/dev/usb/hiddev0 Debian get the usb: # lsusb -v Bus 001 Device 002: ID 10af:0008 Liebert Corp. PowerSure Interactive UPS Device Descriptor: bLength

This patch adds support for the following ups to liebert-hid.c: $ lsusb | grep Liebert Bus 007 Device 005: ID 10af:0001 Liebert Corp. PowerSure PSA UPS Using this patch, I'm able to obtain information about the ups via upsc: $ upsc upsname battery.charge: 100 battery.runtime: 1012 battery.type: PbAc battery.voltage: 1172 battery.voltage.nominal: 12 driver.name: usbhid-ups

Hello, I (now) own an Emerson Liebert GXT3 6000VA conected via USB. I've searched the web trying to configure nut (nut-2.6.5-1.el6.x86_64 epel rpm on CentOS 6.3) to monitor the UPS, but couldn't find a successful configuration. I'm running kernel 2.6.32-279.14.1.el6.x86_64. The UPS is connected with an USB cable: Bus 004 Device 002: ID 10af:0008 Liebert Corp. PowerSure Interactive

Replaced ups with a new Liebert UPS and it seems the device may not be known to nut. Below is output of lsusb: ID 10af:0002 Liebert Corp. PowerSure PST UPS Sent from Outlook<http://aka.ms/weboutlook> -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://alioth-lists.debian.net/pipermail/nut-upsuser/attachments/20231204/7c08a727/attachment.htm>

Hello, I need help configuring my USB connected UPS "Emerson Power Liebert PowerSure PSI 1440" to my freebsd machine, using NUT. here's the manufacturer's product page http://www.emersonnetworkpower.com/en-US/Products/ACPower/Pages/LiebertPowerSurePSILineInteractiveUPS10003000VA.aspx I'm not a BSD expert, so please ask me for any information you need. regards Daniele

please reply to the list. thanks! See below. On Apr 3, 2014, at 3:10 AM, Daniele Borghesi wrote: > thanks for your reply. I'm running the latest version of FreeNAS based on 9.2 with NUT 2.7.1 > > [root at archivio ~]# uname -a > FreeBSD archivio.dannyb78.home 9.2-RELEASE-p3 FreeBSD 9.2-RELEASE-p3 #0 r262572+ > 38751c8: Thu

Hi David As per the link http://www.llondel.org/ups.shtml & the final testing paragraph. I have set up a Lantech UPS similiar to your write up for your Powersure Proactive and Powersure Personal UPS's On LOW BATT it shuts down OK. BUT as with other many UPS's during the wait period from low batt to start of shutdown ... IE [SHUTDOWNCMD "/sbin/shutdown -h +20"]

Problems getting reading from UPS with nut 2.0.2 Debian Sid I know that the server starts running and accepts incoming connections, it can verify the username and password but refutes that the UPS lives at localhost, what am I doing wrong ? I have read and reread both the official documentation and various guides around the net I am unsure where to go now. If the UPS itself is at fault (not

I'd like to submit a patch to the 'hidups' driver. I'm a bit new to open-source development model, so I hope I'm not committing a faux paus by just posting it here. I did verify that the problem still exists (by source code inspection) in the latest dev snapshot, which is nut-2.0.3-pre2. I'm using nut-2.0.2 myself. The problem is when I'm connecting to my APC

Hi, I have a Liebert POWERSURE PSP connected via USB. Cleanly built and installed from source nut-2.4.3.tar.gz using kernel 2.6.30.5 #cat /proc/bus/usb T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=1.5 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=10af ProdID=0003 Rev= 0.00 S: Manufacturer=Liebert S: Product=Liebert PSP 350 FW: 02 S:

Hi Arjen 2007/7/28, Arjen de Korte <adkorte-guest at alioth.debian.org>: > Author: adkorte-guest > Date: Sat Jul 28 16:45:04 2007 > New Revision: 1029 > > Log: > Add Belkin F6C1200-UNV (older model) to supported devices. > > Apparently this is (internally) identical to the F6C1100-UNV. Not surprisingly, they also share the same productid (1100). It also seems to come

I have a 64 bit Gentoo, with a Liebert UPS. The last NUT working version was sys-power/nut-2.4.1-r1 (I also tried sys-power/nut-2.4.3-r2 but downgraded, don't remember the reason). Anyway with the upgrade to sys-power/nut-2.6.0 I started to see this error message when I try to start upsdrv: [root at aemaeth:/etc/nut]$ /etc/init.d/upsdrv start * Starting UPS drivers ... Network UPS Tools -

Jochen Bern wrote: > > Peter Selinger wrote: > > have you been able to get your Liebert UPS to work? If I am correct, > > it should work with the newhidups Belkin subdriver. Could you please > > post your results? I am curious to know if this works or doesn't - and > > if yes, we should add permanent support for Liebert into NUT. > > I'm sorry, but

Hi, I got a Belkin F6C550-AVR UPS today and was trying to get it working with NUT, I used the "hidups" driver and got some data out of it, mainly the following: battery.charge: 100 battery.runtime: 120 driver.name: hidups driver.parameter.port: /dev/usb/hiddev0 driver.version: 2.0.0 ups.mfr: Unknown ups.model: Unknown ups.serial: Unknown ups.status: OL the versions of NUT that I tried

Hi, I got a Belkin F6C550-AVR UPS today and was trying to get it working with NUT, I used the "hidups" driver and got some data out of it, mainly the following: battery.charge: 100 battery.runtime: 120 driver.name: hidups driver.parameter.port: /dev/usb/hiddev0 driver.version: 2.0.0 ups.mfr: Unknown ups.model: Unknown ups.serial: Unknown ups.status: OL the versions of NUT that I tried

Hello, I have encountered problems trying to set up nut to work with APC BackUps Pro CS connected over USB to an AMD64 machine running Debian. While apcupsd works fine with that device, whenever I start upsd I get the following messages in syslog: hidups[23159]: Startup successful upsd[23160]: Connected to UPS [apc1]: hidups-hiddev0 upsd[23161]: Startup successful hidups[23159]: Unhandled event: